This is a good board to demonstrate the use of Mboot because it only has a
USB HS port exposed so the native ST DFU mode cannot be used. With Mboot
this port can be used.
The pin alternate function information is derived from ST's datasheet
https://www.st.com/resource/en/datasheet/stm32l432kc.pdf
In the datasheet, the line 2 of AF4 includes I2C2 but actually the chip
does not have I2C2 so it is removed.
The macros are MICROPY_HEAP_START and MICROPY_HEAP_END, and if not defined
by a board then the default values will be used (maximum heap from SRAM as
defined by linker symbols).
As part of this commit the SDRAM initialisation is moved to much earlier in
main() to potentially make it available to other peripherals and avoid
re-initialisation on soft-reboot. On boards with SDRAM enabled the heap
has been set to use that.
MCUs that have a PLLSAI can use it to generate a 48MHz clock for USB, SDIO
and RNG peripherals. In such cases the SYSCLK is not restricted to values
that allow the system PLL to generate 48MHz, but can be any frequency.
This patch allows such configurability for F7 MCUs, allowing the SYSCLK to
be set in 2MHz increments via machine.freq(). PLLSAI will only be enabled
if needed, and consumes about 1mA extra. This fine grained control of
frequency is useful to get accurate SPI baudrates, for example.
Works with pins declared normally in mpconfigboard.h, eg. (pin_XX), as well
as (pyb_pin_XX).
Provides new mp_hal_pin_config_alt_static(pin_obj, mode, pull, fn_type)
function declared in pin_static_af.h to allow configuring pin alternate
functions by name at compile time.
The code was dereferencing 0x800 and loading a value from there, trying to
use a literal value (not address) defined in the linker script
(_ram_fs_cache_block_size) which was 0x800.
Pins with multiple alt-funcs for the same peripheral (eg USART_CTS_NSS)
need to be split into individual alt-funcs for make-pins.py to work
correctly.
This patch changes the following:
- Split `..._CTS_NSS` into `..._CTS/..._NSS`
- Split `..._RTS_DE` into `..._RTS/..._DE`
- Split `JTDO_SWO` into `JTDO/TRACESWO` for consistency
- Fixed `TRACECK` to `TRACECLK` for consistency
This patch allows a given board to configure which pins are used for the
CAN peripherals, in a similar way to all the other bus peripherals (I2C,
UART, SPI). To enable CAN on a board the mpconfigboard.h file should
define (for example):
#define MICROPY_HW_CAN1_TX (pin_B9)
#define MICROPY_HW_CAN1_RX (pin_B8)
#define MICROPY_HW_CAN2_TX (pin_B13)
#define MICROPY_HW_CAN2_RX (pin_B12)
And the board config file should no longer define MICROPY_HW_ENABLE_CAN.
The individual union members (like SPI, I2C) are never used, only the
generic "reg" entry is. And the union names can clash with macro
definitions in the HAL so better to remove them.
Rather than pin objects themselves. The actual object is now pin_X_obj and
defines are provided so that pin_X is &pin_X_obj. This makes it so that
code that uses pin objects doesn't need to know if they are literals or
objects (that need pointers taken) or something else. They are just
entities that can be passed to the map_hal_pin_xxx functions. This mirrors
how the core handles constant objects (eg mp_const_none which is
&mp_const_none_obj) and allows for the possibility of different
implementations of the pin layer.
For example, prior to this patch there was the following:
extern const pin_obj_t pin_A0;
#define pyb_pin_X1 pin_A0
...
mp_hal_pin_high(&pin_A0);
and now there is:
extern const pin_obj_t pin_A0_obj;
#define pin_A0 (&pin_A0_obj)
#define pyb_pin_X1 pin_A0
...
mp_hal_pin_high(pin_A0);
This patch should have minimal effect on board configuration files. The
only change that may be needed is if a board has .c files that configure
pins.
This patch forces a board to explicitly define TEXT1_ADDR in order to
split the firmware into two separate pieces. Otherwise the default is now
to produce only a single continuous firmware image with all ISR, text and
data together.
This patch allows a particular board to independently specify the linker
scripts for 1) the MCU memory layout; 2) how the different firmware
sections are arranged in memory. Right now all boards follow the same
layout with two separate firmware section, one for the ISR and one for the
text and data. This leaves room for storage (filesystem data) to live
between the firmware sections.
The idea with this patch is to accommodate boards that don't have internal
flash storage and only need to have one continuous firmware section. Thus
the common.ld script is renamed to common_ifs.ld to make explicit that it
is used for cases where the board has internal flash storage.
genhdr/pins.h is an internal header file that defines all of the pin
objects and it's cleaner to have pin.h include it (where the struct's for
these objects are defined) rather than an explicit include by every user.
The CMSIS files for the STM32 range provide macros to distinguish between
the different MCU series: STM32F4, STM32F7, STM32H7, STM32L4, etc. Prefer
to use these instead of custom ones.
Newer versions of the HAL use names which are cleaner and more
self-consistent amongst the HAL itself. This patch switches to use those
names in most places so it is easier to update the HAL in the future.
mpconfigboard_common.h now sets the defaults so there is no longer a need
to explicitly list all configuration options in a board's mpconfigboard.h
file.
This is a low-cost evaluation kit board from ST based on the STM32
Nucleo-144 form factor. It uses the STM32F746ZG MCU in the LQFP144
package. The MCU has 1MB of flash and 320kB of System RAM.
Cortex-M7 runs at up to 216MHz.
This is to keep the top-level directory clean, to make it clear what is
core and what is a port, and to allow the repository to grow with new ports
in a sustainable way.
Damien George