Transceiver "Wolf"

DDC-DUC SDR Transceiver project https://ua3reo.ru/tag/transiver-ua3reo/

• Community telegram channel: https://t.me/TRX_Wolf
• На русском https://github.com/XGudron/UA3REO-DDC-Transceiver/blob/master/README.ru-RU.md

Principle of operation

The RF signal is digitized by a high-speed ADC chip and fed to an FPGA processor.
It performs DDC / DUC conversion (digital frequency shift down or up the spectrum) - by analogy with a direct conversion receiver.
The I and Q quadrature signals from the conversions are fed to the STM32 microprocessor.
It filters, (de) modulates and outputs audio to an audio codec / USB. It also handles the entire user interface.
When transmitting, the process occurs in the opposite order, only at the end of the chain there is a DAC, which converts the digital signal back to analog RF.

Specifications TRX Wolf-2

• Receiving frequencies: 0 Mhz - 2700 Mhz, band filters for ham bands (23cm included)
• Transmission frequencies: 0 MHz - 2700 Mhz, amplifiers for ham bands (23cm included)
• TX power: 100W (HF), 50W+ (VHF/UHF), 15W+ (SHF)
• Two antenna inputs on HF, four for VHF/UHF/SHF/Wideband
• Automatic antenna tuner
• Modulation types (TX / RX): CW, LSB, USB, AM, FM, WFM, DIGI
• LNA, Preamplifier
• Adjustable attenuator 0-31dB
• Band pass filters
• ADC dynamic range (16 bit) ~100dB
• Supply voltage: 13.8V

Specifications TRX Wolf-1

• Receiving frequencies: 0 MHz - 750 MHz with fading each 61.44 MHz (above 145 MHz - without input filters)
• Transmission frequencies: 0 MHz - 150 MHz with fading on 110 MHz
• TX power (QRP version): 7W+ (HF), 5W (VHF)
• TX power (QRP++ DB5AT version): 20W (HF), 7W (VHF)
• TX power (RU4PN/WF-100D version): 100W (HF), 50W+ (VHF)
• Two antenna inputs
• Modulation types (TX / RX): CW, LSB, USB, AM, FM, WFM, DIGI
• LNA, Preamplifier
• Adjustable attenuator 0-31dB
• Band pass filters
• ADC dynamic range (16 bit) ~100dB
• Supply voltage: 13.8V (overvoltage and polarity reversal protection)
• Consumption current when receiving: ~0.7А (3'2 QRP), 0.9A (7' BIG)
• Current consumption during transmission: ~2.5А+ (QRP), 15A+ (BIG)
• Support for different displays: RA8875/HX8357B/HX8357C/ST7789/ST7796S/ST7735S/ILI9341/ILI9481/ILI9486/ILI9488

Transceiver Features

• Panorama (spectrum + waterfall) up to 384 kHz wide
• Panorama tweaks and themes
• Dual receiver (mixing A + B or A&B audio in stereo)
• Adjustable bandwidth: HPF from 0Hz to 2700Hz, LPF from 100Hz to 20kHz
• Integrated SWR/power meter (HF)
• Automatic and manual Notch filter
• Switchable AGC (AGC) with adjustable attack rate
• Range map, with the ability to automatically switch modes
• Digital Noise Reduction (DNR), Pulse Noise Reduction (NB)
• CAT virtual COM port (TS-2000 / FT-450 emulation, RTS - PTT, DTR - CW)
• USB operation (audio transmission, IQ, CAT, KEY, PTT)
• RDS/CW/RTTY decoder, self-control, gauss filter
• SWR Graphs
• Spectrum analyzer
• FT8 receiver/transmitter
• Automatic send FT8 qso to log https://allqso.ru/
• WSPR Beacon
• VOX
• Equalizer TX/RX, reverber
• SSB/FM Scanner mode
• Support SDHC/SDSC/SDXC memory cards up to 16Gb
• WAV files radio recording and playback, fast broadcast recorded CQ message
• AGC takes into account the characteristics of human hearing (K-Weighting)
• TCXO frequency stabilization (it is possible to use an external clock source, such as GPS)
• WiFi operation: Time synchronization, external WiFi services
• Tangent support Yaesu MH-36 и MH-48
• Hardware self-testing
• Firmware update over USB, SD, WiFi
• And other.. (see menu)

RF Parameters

Sensitivity at 10 dB SNR, LNA enabled:

• <150 MHz | -131 dBm | 63.0 nV
• 435 MHz | -121 dBm | 0.2 uV

Out-of-band emissions:

• 14 MHz -69 dBc
• 28 MHz -63 dBc
• 145 MHz -48 dBc -55 dBc

Build

I ordered the boards in the Chinese service JLCPCB, they and their schemes are in the Scheme folder.
After assembly, you need to flash FPGA and STM32 chips.
If necessary, calibrate the transceiver through the appropriate menu
WiFi module ESP-01 must have fresh firmware with SDK 3.0.4 and higher, and AT commands 1.7.4 and higher

Management

• AF GAIN - Volume
• RIT / GAIN - When the RIT function is active - smooth offset from the selected transceiver frequency. Inactive - IF gain control
• ENC MAIN - Main encoder for frequency control and menu settings
• ENC 2 - Auxiliary encoder for menu operation. In normal mode, quickly switches the frequency, in CW fast change WPM
• ENC 2[click] - In CW mode, toggles between fast step and WPM selection, in other modes it opens the bandwidth properties.
• BAND - - Switch to the band below
• BAND + - Switch to higher band
• MODE - - Mode group switching SSB-> CW-> DIGI-> FM-> AM
• MODE + - Switching subgroup mode LSB-> USB, CW_L-> CW_U, DIGI_U-> DIGI_L, NFM-> WFM, AM-> IQ-> LOOP
• FAST - Mode of fast x10 rewinding of the frequency by the main encoder (configurable)
• FAST [clamp] - Frequency step settings
• PRE - Turn on the preamplifier (LNA)
• PRE [clamp] - Turn on the driver and / or amplifier ADC
• ATT - Turn on the attenuator
• REC - Save audio to SD card
• CQ - Play recorded CQ-message from SD card
• MUTE - Mute the sound
• MUTE [clamp] - Scanner mode
• AGC - Turn on AGC (automatic gain control)
• AGC [clamp] - AGC settings
• A = B - Setting the second bank of the receiver equal to the current
• BW - Switch to bandwidth selection menu (LPF)
• BW [clamp] - Switch to bandwidth selection menu (HPF)
• TUNE - Turn on the carrier for tuning the antenna
• RF POWER - Transmitter power selection
• RF POWER [clamp] - Squelch setting
• A / B - Switches between VFO-A / VFO-B receiver settings banks
• A / B [clamp] - Enable automatic mode change by bandmap
• DOUBLE - Turn on the dual receiver
• DOUBLE [clamp] - Switching between the modes of the dual receiver A&B (each channel of the headphones has its own path) or A + B (mixing signals of 2 receivers)
• DNR - Enable digital noise reduction
• DNR [clamp] - Turn on the impulse noise suppressor (NB)
• NOTCH - Turn on the automatic Notch filter to eliminate narrowband interference
• NOTCH [clamp] - Turn on the manual Notch filter to eliminate narrowband interference
• SPLIT - Allows you to split transmission and reception to different VFO banks
• RIT [clamp] - Enables RIT control from the front panel
• WPM - Switch to key speed selection menu (WPM)
• WPM [clamp] - Automatic key enable
• MENU - Go to the menu
• MENU [clamp] - Enable key lock LOCK
• MENU [at power on] - Reset transceiver settings
• MENU [at power on+PRE] - Reset transceiver settings and calibration
• RIT - Offset of the receiving frequency relative to the current frequency (TX without offset)
• XIT - Offset of the transmission frequency relative to the current frequency (RX without offset)

Settings

TRX Settings

• Band Map - Band Map, automatically switches mode depending on the frequency
• Beeper - Beep on key press
• Callsign - User callsign
• Channel Mode - Channel frequency mode (for LPD/PMR and etc.)
• Custom Transverter - Enable external transverter on non-ham band (just offset display frequency)
• DEBUG Type - Output of debug and service information to USB / UART ports
• Encoder Accelerate - Accelerate encoder on fast rates
• Fine RIT Tune - Fine or coarse tuning for RIT/XIT (encoder or resistor)
• Freq Step xxx - Frequency step by main encoder in each mode, Hz
• FAST Step Multiplier - Frequency step multiplier for FAST mode
• ENC2 Step Mult - Frequency step multiplier for ENC2 rotation (for CW/SSB)
• Notch Step - Frequency step of manual notch filter
• Full Duplex - Full duplex RX+TX mode
• Locator - User QTH locator
• SPLIT type - In DX mode - the TX frequency is controlled, in the CrossBand mode synchronously for two VFOs, for Free only the RX frequency changes
• RIT Interval - Offset range RIT (+ -)
• XIT Interval - Offset range XIT (+ -)
• Transverter XXcm - Enable external ham band transverter support
• URSI Code - Ionogram URSI Code https://digisonde.com/index.html#stationmap-section
• Tropo Region - Region for tropospheric forecast https://www.dxinfocentre.com/tropo.html
• Wolf Cluster - Display Wolf TRX users on spectrum and send self data

FILTERS Settings

• Adaptive FM Filter - Automatic adjustment of the width of the NFM filter relative to the strength of the received signal (VHF)
• AM/FM/CW/SSB LPF Stages - Adjusting the slopes of the LPF filters in different modes
• CW LPF Pass - LPF cutoff frequency when working in CW
• CW Gauss filter - Use a filter with a Gaussian distribution (for CW), accepts only the peak in the center of the BW
• CW Gauss Q - Quality of Gauss filter
• DIGI LPF Pass - LPF cutoff frequency when working in DIGI
• FM LPF Pass - LPF cutoff frequency when working in FM
• SSB HPF Pass - HPF cutoff frequency when operating in SSB
• SSB LPF Pass - LPF cutoff frequency when operating in SSB
• NOTCH Filter width - Cutting width of Manual Notch filter

RX Settings

• ADC Dither - Enable ADC dither for receiving weak signals
• ADC Driver - Turn on the preamplifier-ADC driver
• ADC Preamp - Turn on the preamplifier built into the ADC
• ADC Randomizer - Enables ADC digital line encryption
• AGC Gain target, LKFS - Maximum AGC gain (Maximum volume with AGC on)
• AGC Threshold - Enabling the AGC opening threshold
• Att step, dB - Attenuator tuning step
• Attenuation, dB - Current attenuation
• Auto Snap - Automatically track and snap to near signal frequency (CW mode)
• AutoGainer - Automatic ATT / PREAMP control depending on the signal level on the ADC
• A/B Balance - Channels balance in dual RX modes A+B and A&B
• CODEC Gain - Adjusting AF gain in audio codec
• DNR xxx - Digital squelch adjustment
• Squelch - Enable SSB/AM/CW/FM Squelch
• FM Squelch level - FM squelch level
• IF Gain, dB - IF gain
• NB Threshold - Threshold of Noise blanker
• Free tune - Allows you to move the reception frequency across the spectrum without changing the center frequency of the spectrum itself
• Center After Idle - Center the spectrum with Free Tune active after 20 seconds of inactivity
• Noise Blanker - Activating the Surge Suppressor
• RX AUDIO Mode - Audio lines control: Stereo\Left\Right
• RX AGC Hold time - Time before release of AGC gain in signal peaks, ms
• RX AGC Hold limit - Burst limit for AGC delay time
• RX AGC Hold step up - AGC Delay Time Step on Peaks
• RX AGC Hold step down - AGC Delay Falloff Step at Peaks
• RX AGC Max gain - Limit of AGC gain, dB
• RX AGC Speed - AGC (automatic signal level control) response speed for reception (more-faster)
• TRX Samplerate - Max FFT/samplerate on SSB/DIGI/etc modes
• FM Samplerate - Max FFT/samplerate on NFM/WFM mode
• CW Samplerate - Max FFT/samplerate on CW mode
• VAD Threshold - VAD voice detector threshold (noise suppressor for SSB mode and SCAN mode)
• Volume step - AF gain step by ENC2 (X1, Lite)
• Volume - AF gain
• WFM Stereo - select WFM stereo or mono decoder
• WFM Stereo Modulation - Stereo FM sub-carrier level

TX Settings

• ADC Shutdown - Turn off the ADC while TX
• ATU Cap - Tuner Capacitance Combination
• ATU Enabled - Turning on the automatic antenna tuner
• ATU Ind - Combination of tuner inductances
• ATU T - Tuner capacitive arm position
• ATU Mem step, kHz - Step of saving tuner values for frequencies into memory
• Auto Input Switch - Auto input switch (PTT - mix, CAT - USB)
• CESSB - Enable controlled-envelope single-sideband modulation
• CESSB Compress, dB - Signal pre-amplification level before compression in CESSB
• DRV Shutdown - Turn off the DAC driver while RX
• TX AGC MaxGain - Maximum AGC gain
• TX AGC Speed - TX compressor response speed for transmission (more-faster)
• CTCSS Frequency - Transmit FM CTCSS sub-tone frequency
• FT8 Auto CQ - Automatic transition to CQ mode after FT8 communication
• Input Type - Select audio input (microphone, line in, USB)
• LINE Gain - Line input codec gain
• MIC Boost - +20db hardware mic amplifier
• MIC Gain - Microphone gain
• MIC DSP Type - Type of DSP processing of the microphone path: None, Downward Expander, Upward/Downward Compressor, Limiter, Noise Gate
• MIC DSP Threshold - Threshold of selected microphone DSP processing
• MIC DSP Ratio - Level of slope for selected microphone DSP processing
• MIC Reverber - Microphone reverberator level
• Power for each band - Save power settings for each band individually
• Power for each mode - Save power settings for each mode individually
• RF Power - Transmission power,%
• Repeater Mode" - Operation mode via repeater
• Repeater offset, kHz" - Transmission frequency offset in repeater mode
• SelfHear CW - Self-control CW Gain
• SelfHear on SSB - Self-monitoring for SSB/AM modes, always active for DIGI/RTTY/LOOPBACK
• SelfHear VOICE - Self Hearing volume at voice modes relative to the overall transceiver volume
• SelfHear DIGI - Self Hearing volume at DIGI modes relative to the overall transceiver volume
• TUNER Enabled - Turning on the antenna tuner
• Tune Type - TUNE operating mode (carrier, two signal tone, multi-tone, white noise)
• TOT, min - Protection of the transmitter from long-term operation, automatic shutdown after time has elapsed
• VOX Threshold, dbFS - VOX Threshold, dbFS
• VOX Timeout, ms - VOX transmission delay after silence, milliseconds
• VOX - TX Voice activation

CW Settings

• Auto CW Mode - Automatic switching to CW mode when pressing the key, or only manipulation during transmission
• DotToDash Rate - Keyer dash to dot length rate
• Edges smooth, ms - Smoothing signal edges
• Iambic Keyer - Enable Iambic mode keyer
• Iambic Type - Type of Iambic keyer (A/B)
• Key Invert - Invert dash/dot on key
• Key timeout - Time before stopping the transmission mode after releasing the key
• Keyer WPM - Key Speed, WPM
• Keyer - Automatic Key
• One symbol memory - Keyer memory for one symbol for transmit
• PTT Type - RX/TX switch type for CW: by key or external PTT (tangent, etc.)
• Pitch - Detuning the receiver generator from the transmit frequency
• Self Hear - Self-control CW (key press is heard)
• Macros x - Setting up macros for CW transmission
• Macros x name - Setting the macro name to be displayed in the interface

Equalizer Settings

• RX EQ xxx - Receiver equalizer levels
• MIC EQ xxx - Microphone equalizer levels

SCREEN Settings

• Bottom navi buttons - Show bottom menu navigation buttons (for 7 inch displays)
• Color Theme - Select colors theme (0 - black, 1 - white, 2 - black with colored frequency)
• Layout Theme - Select interface theme (0 - default)
• DX Cluster Type - Selecting a Data Source for a DX Cluster
• FFT 3D Mode - Enable FFT 3D mode (0 - disabled, 1 - lines, 2 - pixels)
• FFT Automatic - Automatic FFT scale
• FFT Averaging - FFT burst averaging level. Full - automatic selection of upper and lower boundaries, Half - auto lower and manual upper, No - manual setting of the range of spectrum levels. (Remember to select the correct FFT Scale Type so that your range will fit on the screen)
• FFT BW Style - FFT bandwidth style: high opacity, low opacity, lines
• FFT BW Position - Position of the receiving band on FFT/WTF (everywhere \ at the top \ at the top + lines \ top + bottom with time delay)
• FFT Background - Gradient FFT background
• FFT Color - FFT colors: 1(blue -> yellow -> red), 2(black -> yellow -> red), 3(black -> yellow -> green), 4(black -> red), 5(black -> green), 6(black -> blue), 7(black -> white)
• FFT Compressor - Enable FFT peak comressor
• FFT DXCluster Azimuth - Add azimuth data to DX-cluster
• FFT DXCluster Timeout - Timeout of DX-cluster spots in minutes
• FFT DXCluster - Show DXCluster info over FFT
• FFT Enabled - Enable waterfall and FFT
• FFT Freq Grid - FFT and waterfall grids: 1(no grid), 2(fft grid), 3(fft+wtf grids), 4(wtf grid)
• FFT Height - FFT and waterfall proportional height
• FFT Hold Peaks - Show peaks on FFT spectrum
• FFT Lens - Enable FFT lens mode (magnify center of spectrum)
• FFT Manual Bottom, dBm - Bottom FFT threshold in manual mode
• FFT Manual Top, dBm - Top FFT threshold in manual mode
• FFT Scale Type - Y-axis style on FFT between signal amplitude and dBm to fit more dynamic range on screen (Useful when manually adjusting FFT range).
• FFT Sensitivity - Top threshold of FFT sensitivity in automatic mode (30 - scale to strongest signal)
• FFT Speed - FFT and waterfall speed
• FFT Style - FFT style: 1(gradient), 2(fill), 3(dots), 4(contour), 5(gradient + contour)
• FFT Window - Select FFT window (1-Dolph–Chebyshev 2-Blackman-Harris 3-Nutall 4-Blackman-Nutall 5-Hann 6-Hamming 7-No window)
• FFT dBm Grid - FFT signal power grid
• LCD Brightness - Set LCD brightness (not all lcd support)
• LCD Sleep Timeout - Idle time before the screen brightness decreases, sec (0 - disabled)
• S-Meter style - Selecting layout of the analog S-Meter
• Show Sec VFO - Show secondary VFO position on spectrum
• WTF Color - Waterfall colors: 1(blue -> yellow -> red), 2(black -> yellow -> red), 3(black -> yellow -> green), 4(black -> red), 5(black -> green), 6(black -> blue), 7(black -> white)
• WTF Moving - Mowe waterfall with frequency changing

Decoders

• CW Decoder - Software CW receive decoder
• CW Decoder Threshold - CW receive decoder sensivity
• RDS Decoder - Enable RDS Decoder for WFM mode
• RTTY Freq - Central frequency of RTTY decoding
• RTTY InvertBits - RTTY invert 0 and 1 bits
• RTTY Shift - RTTY carrier shifts
• RTTY Speed - Speed of RTTY data
• RTTY StopBits - RTTY Stop bits

WIFI Settings

• WIFI Enabled - Enable WiFi module (need restart after enable)
• WIFI Network - WiFi hotspot selection
• WIFI Network Pass - Set password for WiFi hotspot
• WIFI Timezone - Time zone (for updating the time via the Internet)
• WIFI Update ESP firmware - Start cloud autoupdate firmware for ESP-01 (if present)
• ALLQSO.RU Token/LogId - Token и LogID from https://allqso.ru/ web-log

SD Card

• File Manager - Show SD Card file manager, support WAV playback and deleting files, listening and broadcasting recordings, as well as updating firmware from a memory card
• Record CQ message - Record a short message for quick broadcast
• USB SD Card Reader - Enable USB SD Card reader
• Export Settings - Export settings and calibration data to SD card
• Import Settings - Import settings and calibration data from SD card
• Format SD card - Format media drive

Satellites

• SAT Mode - Enable satellite mode
• Auto Doppler - Automatically shifts the transceiver frequency based on the calculated Doppler effect
• Download TLE - Download current satellite data
• Select SAT - Select a satellite from the downloaded TLE file
• Calc Pass - Calculate future satellite passes over QTH (Local time)
• QTH xxx - Setting the Latitude\Longitude\Altitude of your location

Calibration [appears by long pressing the MENU button in the settings menu]

Calibration Bands

• ENABLE 2200m/60m/6m/4m/FM/2m/AIR/Marine Band/70cm - Enable hidden bands
• NOTX xxx - Disable TX on selected bands

Calibration Control

• CAT Type - Type of CAT subsystem (FT-450 / TS-2000)
• COM CAT DTR/RTS - Configuring the functions of the DTR/RTS control lines of the CAT port
• SEC COM Mode - Select the operating mode of the secondary COM port (debugging, CAT)
• SEC COM DTR/RTS - Configuring the functions of the DTR/RTS control lines of the Debug port
• FAN Full start - Temperature of the PA for starting the fan at full speed
• FAN Medium start - Temperature of the PA for starting the fan at medium speed
• FAN Medium stop - Temperature of the PA for stopping the fan
• FAN MB --- - STM32 Temperature fan enable settings
• FAN Medium PWM - Adjusting the duty cycle of a PWM fan in Medium mode
• FAN Motherboard - Starting the fan not only by the sensor, but also by the temperature of the STM32 processor
• IF Gain MIN/MAX - IF Gain adjusting limits
• OTA Update - Enable OTA firmware update over WiFi

Calibration Hardware

• RF-Unit Type - RF-Unit Type (QRP / BIG)
• ALC Port Enabled - Activation of transceiver power control by an external amplifier via the ALC line: up to 1 volt - ALC is disabled and the power set in the transceiver is used. from 1.0v to 3.0v - power adjustment from 0 to 100%
• ALC Inverted - Invert ALC logic (3.0v - 0%, 1.0v - 100%)
• BPF x - Bandpass filter parameters
• HPF START - HPF filter parameters
• LPF END - LPF filter parameters
• DAC Driver Mode - DAC Driver OPA2673 bias mode (2 = 100% bias, 1 = 75% bias, 0 = 50% bias)
• DAC Interpolation - Using interpolation in the first DAC frequency zone (HF)
• EXT xxx - External port control by band (EXT3, EXT2, EXT1, EXT0) - open drain
• Encoder acceleration - The encoder acceleration on faster rotation speeds
• Encoder debounce - Time of debouncing contacts of the main encoder
• Encoder invert - Invert the rotation of the main encoder
• Encoder on falling - The encoder is triggered only when level A falls
• Encoder slow rate - Deceleration rate of the main encoder
• Encoder2 debounce - Time of debouncing contacts of the additional encoder
• Encoder2 invert - Invert the rotation of the additional encoder
• Encoder2 on fall - Mode of operation of the secondary encoder (some encoders skip a step or make an extra one)
• Flash GT911 - Starting the touchpad update procedure according to LCD screen resolution
• INA226 - Activation and calibration of the INA226 voltage/current sensor on the I2C bus
• KTY81 Calibration - Calibration of the KTY81 sensor (setting the resistance of the divider arm)
• LCD Rotate - Rotate screen at 180 degrees
• MAX ChargePump, kHz - Maximum PWM frequency for ChargePump circuit
• RTC COARSE CALIBR - Very coarse clock crystal calibration
• RTC FINE CALIBR - Clock crystal calibration, one division is 0.954 ppm
• Sequencer support - External sequencer support (output through line EXT_TUNE)
• TCXO Frequency, kHz - Frequency adjustment of the reference oscillator
• VCXO Correction - Correction for main generator frequency offset
• Touchpad flip - Flip the touchpad operation horizontally/vertically
• Touchpad timeout - Minimum time between taps (protection against false trigger), ms
• Touchpad click threshold - Minimum time for triggering a short click, ms
• Touchpad click timeout - Maximum time for triggering a short click, ms
• Touchpad hold timeout - Time before a long press is triggered, ms
• Touchpad swipe threshold - Minimum distance to trigger a swipe, px
• Tangent Type - Select tangent type
• Transverter Offset, MHz - Offset frequency shown on the display (for custom transverters)
• Transverter xxx IF, MHz - Setting the IF frequency of the transverter
• Transverter xxx RF, MHz - Setting the RF frequency of the transceiver to match the IF
• Transv only TX - Use transverter only for TX
• VHF Mixer Board - Enable VHF board with RF mixer support (Wolf-2)
• VHF Mixer IF, MHz - Select IF frequency for VHF board mixer (Wolf-2)
• VHF TCXO, kHz - Select TCXO frequency for VHF board (Wolf-2)
• VHF TCXO Correction - Correction for VHF board TCXO generator frequency offset (Wolf-2)

Calibration RX

• ATT Compensation - Compensates the S-meter value when the ATT is turned on
• LNA Compensation - Compensates the S-meter value when the LNA is turned on, dBm
• CICCOMP Shift - Bit shift after CIC compensator
• S METER - S-meter calibration (LHF 160/80, MHF 40/30/20/17, HHF 15/12/10, 6M, VHF, SHF)
• Swap USB IQ - Swap USB IQ output

Calibration TX

• AM Modulation Index - Set TX AM Modulation Scale
• ATU Averaging - The number of steps of averaging SWR values during measurements in the operation of an automatic tuner
• TX CICCOMP Shift - Bit shift after TX CIC compensator
• DAC Shift - Bit shift of the output to the DAC
• FM Deviation Scale - Set TX FM Deviation Scale
• Linear Pwr Control - Sets a linear way to change the signal amplitude when adjusting the power (if disabled - logarithmic)
• MAX PWR on Meter - Maximum RF power (for indication)
• MAX Power in TUNE - Maximum RF power in Tune mode
• MAX RF Temp - Maximum temperature of the PA before the protection operation
• MAX SWR - Maximum VSWR before protection operation
• Max Current, Amp - Current protection, turns off transmission when the threshold is reached
• RF GAIN xxx - Calibration of the maximum TX output power for each range
• SSB Power addition - Addition of RF power in SSB power, %
• SWR FWD/BWD RATE - Adjustment of the transformation ratio of the SWR meter (forward / return)
• SWR Protector - SWR protection mode selection: Off, low power, transmission off
• TSignal Balance - Sets the power balance between signals in Two signal tune mode
• TX Start Delay - Delay before the RF signal is applied (ms), so that the relay has time to trigger

Calibration Reset

• Settings reset - Reset all settings to defaults
• Calibrate reset - Reset all calibrations to defaults
• WiFi Settings reset - Reset all WiFi setitngs to defaults

Memory Channels

• Changing names for transceiver memory channels

Set Clock Time

• Clock setting

DFU Mode

• Launch STM32 USB firmware update over DFU mode

OTA Update

• Launch FPGA/STM32 firmware update over internet

System info

• Show info about TRX

Services

Spectrum Analyzer

• Spectrum START - Start the spectrum analyzer
• Begin, kHz - Starting frequency of the analyzer with a step of 1 kHz
• End, kHz - End frequency of the analyzer in 1 kHz steps
• Top, dBm - Upper threshold of the graph
• Bottom, dBm - Lower threshold of the graph

WSPR Beacon

• WSPR Beacon START - Start WSPR beacon
• Freq offset - Offset from center of WSPR band
• WSPR Band xxx - Select bands to WSPR beacon

DX Cluster

• Show DX Cluster info by current band (from internet)

WOLF Cluster

Displays information about radio amateurs currently in the current band using "Wolf" transceivers (internet connection required)

Propagation

• Show propagation statistics (from internet)

Tropo

• Show tropospheric forecast

DayNight Map

• Displaying the day/night terminator on the map (from internet)

Ionogram

• Displaying the ionogram for the selected URSI Code (from internet)

foF2 Map

• Displaying the foF2 frequency map (from internet)

SWR Analyzer

• Run SWR analyzer (Band SWR - on current band, HF SWR - on all HF bands, Custom SWR - in selected range)

RDA Statistics

• Print statistics from RDA award (from internet)

FT8

• FT8 Receiver / transmitter

Locator Info

• Calculate distance and azimuth from QTH-locator

Callsign Info

• Show callsign data

Time Beacons

• List of beacons of the exact time (for adjusting the frequency of reception by carrier)

Self Test

• Run hardware self diagnostic

Auto calibration

• Calibrate SWR - Assistant in measuring SWR and power meter
• Calibrate Power - Assistant in adjusting RF Power output