13 KiB

Czysty Wina Historia

High priority

Items to complete soon (next couple of alpha releases).

stay awake while charging
check gps battery voltage
The following three items are all the same: Have state machine properly enter deep sleep based on loss of mesh and phone comms. Default to enter deep sleep if no LORA received for two hours (indicates user has probably left the mesh). If the phone doesn't read fromradio mailbox within X seconds, assume the phone is gone and we can stop queing location msgs for it (because it will redownload the nodedb when it comes back)
lower wait_bluetooth_secs to 30 seconds once we have the GPS power on (but GPS in sleep mode) across light sleep. For the time being I have it set at 2 minutes to ensure enough time for a GPS lock from scratch.
retest BLE software update for both board types
send note about Adafruit Clue
report on wikifactory
send note to the guy who designed the cases
remeasure wake time power draws now that we run CPU down at 80MHz

Medium priority

Items to complete before the first beta release.

make mesh aware network timing state machine (sync wake windows to gps time)
turn light sleep on aggressively (while lora is on but BLE off)
research and implement better mesh algorithm
the BLE stack is leaking about 200 bytes each time we go to light sleep
use gps sleep mode instead of killing its power (to allow fast position when we wake)
rx signal measurements -3 marginal, -9 bad, 10 great, -10 means almost unusable. So scale this into % signal strength. preferably as a graph, with an X indicating loss of comms.
assign every "channel" a random shared 8 bit sync word (per 4.2.13.6 of datasheet) - use that word to filter packets before even checking CRC. This will ensure our CPU will only wake for packets on our "channel"
Note: we do not do address filtering at the chip level, because we might need to route for the mesh
Use the Periodic class for both position and user periodic broadcasts
make debug info screen show real data (including battery level & charging)
don't forward redundant pings or ping responses to the phone, it just wastes phone battery
don't treat north as up, instead adjust shown bearings for our guess at the users heading (i.e. subtract one from the other)
answer to pings (because some other user is looking at our nodeinfo) with our latest location
show radio and gps signal strength as an image
only BLE advertise for a short time after the screen is on and button pressed - to save power and prevent people for sniffing for our BT app.
use https://platformio.org/lib/show/1260/OneButton if necessary
make an about to sleep screen
don't send location packets if we haven't moved
scrub default radio config settings for bandwidth/range/speed
add basic crypto - http://rweather.github.io/arduinolibs/crypto.html with speck https://www.airspayce.com/mikem/arduino/RadioHead/rf95_encrypted_client_8pde-example.html
override peekAtMessage so we can see any messages that pass through our node (even if not broadcast)? would that be useful?
sendToMesh can currently block for a long time, instead have it just queue a packet for a radio freertos thread
How do avalanche beacons work? Could this do that as well? possibly by using beacon mode feature of the RF95?
use std::map<NodeInfo*, std::string> in node db
make a HAM build: yep - that's a great idea. I'll add it to the TODO. should be pretty painless - just a new frequency list, a bool to say 'never do encryption' and use hte callsign as that node's unique id. -from Girts
add frequency hopping, dependent on the gps time, make the switch moment far from the time anyone is going to be transmitting
publish update articles on the web

Pre-beta priority

During the beta timeframe the following improvements 'would be nice' (and yeah - I guess some of these items count as features, but it is a hobby project ;-) )

Figure out why the RF95 ISR is never seeing RH_RF95_VALID_HEADER, so it is not protecting our rx packets from getting stomped on by sends
use BLEDevice::setPower to lower our BLE transmit power - extra range doesn't help us, it costs amps and it increases snoopability
make an install script to let novices install software on their boards
fix the frequency error reading in the RF95 RX code (can't do floating point math in an ISR ;-)
See CustomRF95::send and fix the problem of dropping partially received packets if we want to start sending
swap out speck for hw-accelerated full AES https://github.com/espressif/arduino-esp32/blob/master/tools/sdk/include/esp32/hwcrypto/aes.h
use variable length arduino Strings in protobufs (instead of current fixed buffers)
don't even power on bluetooth until we have some data to send to the android phone. Most of the time we should be sleeping in a lowpower "listening for lora" only mode. Once we have some packets for the phone, then power on bluetooth until the phone pulls those packets. Ever so often power on bluetooth just so we can see if the phone wants to send some packets. Possibly might need ULP processor to help with this wake process.
do hibernation mode to get power draw down to 2.5uA https://lastminuteengineers.com/esp32-sleep-modes-power-consumption/
make sure main cpu is not woken for packets with bad crc or not addressed to this node - do that in the radio hw
enable fast init inside the gps chip
triple check fcc compliance
pick channel center frequency based on name? "dolphin" would hash to 900Mhz, "cat" to 905MHz etc? Or is that too opaque?
scan to find channels with low background noise?
share channel settings over Signal (or qr code) by embedding an an URL which is handled by the MeshUtil app.

Low priority

Items after the first final candidate release.

Use CAD mode of the RF95 to automatically find low noise channels
read the PMU battery fault indicators and blink/led/warn user on screen
make a no bluetooth configured yet screen - include this screen in the loop if the user hasn't yet paired
the AXP debug output says it is trying to charge at 700mA, but the max I've seen is 180mA, so AXP registers probably need to be set to tell them the circuit can only provide 300mAish max. So that the low charge rate kicks in faster and we don't wear out batteries.
increase the max charging rate a bit for 18650s, currently it limits to 180mA (at 4V). Work backwards from the 500mA USB limit (at 5V) and let the AXP charge at that rate.
if radio params change fundamentally, discard the nodedb
discard very old nodedb records (> 1wk)
using the genpartitions based table doesn't work on TTGO so for now I stay with my old memory map
We let anyone BLE scan for us (FIXME, perhaps only allow that until we are paired with a phone and configured)
use two different buildenv flags for ttgo vs lora32. https://docs.platformio.org/en/latest/ide/vscode.html#key-bindings
sim gps data for testing nodes that don't have hardware
have android provide position data for nodes that don't have gps
do debug serial logging to android over bluetooth
break out my bluetooth OTA software as a seperate library so others can use it
Heltec LoRa32 has 8MB flash, use a bigger partition table if needed - TTGO is 4MB but has PSRAM
add a watchdog timer
fix GPS.zeroOffset calculation it is wrong
handle millis() rollover in GPS.getTime - otherwise we will break after 50 days
reneable the bluetooth battery level service on the T-BEAM, because we can read battery level there
report esp32 device code bugs back to the mothership via android

Done

change the partition table to take advantage of the 4MB flash on the wroom: http://docs.platformio.org/en/latest/platforms/espressif32.html#partition-tables
wrap in nice MeshRadio class
add mesh send & rx
make message send from android go to service, then to mesh radio
make message receive from radio go through to android
test loopback tx/rx path code without using radio
notify phone when rx packets arrive, currently the phone polls at startup only
figure out if we can use PA_BOOST - yes, it seems to be on both boards
implement new ble characteristics
have MeshService keep a node DB by sniffing user messages
have a state machine return the correct FromRadio packet to the phone, it isn't always going to be a MeshPacket. Do a notify on fromnum to force the radio to read our state machine generated packets
send my_node_num when phone sends WantsNodes
have meshservice periodically send location data on mesh (if device has a GPS)
implement getCurrentTime() - set based off gps but then updated locally
make default owner record have valid usernames
message loop between node 0x28 and 0x7c
check in my radiolib fixes
figure out what is busted with rx
send our owner info at boot, reply if we see anyone send theirs
add manager layers
confirm second device receives that gps message and updates device db
send correct hw vendor in the bluetooth info - needed so the android app can update different radio models
correctly map nodeids to nodenums, currently we just do a proof of concept by always doing a broadcast
add interrupt detach/sleep mode config to lora radio so we can enable deepsleep without panicing
make jtag work on second board
implement regen owner and radio prefs
use a better font
make nice screens (boot, about to sleep, debug info (gps signal, #people), latest text, person info - one frame per person on network)
turn framerate from ui->state.frameState to 1 fps (or less) unless in transition
switch to my gui layout manager
make basic gui. different screens: debug, one page for each user in the user db, last received text message
make button press cycle between screens
save our node db on entry to sleep
fix the logo
sent/received packets (especially if a node was just reset) have variant of zero sometimes - I think there is a bug (race-condtion?) in the radio send/rx path.
DONE dynamic nodenum assignment tasks
make jtag debugger id stable: https://askubuntu.com/questions/49910/how-to-distinguish-between-identical-usb-to-serial-adapters
reported altitude is crap
good tips on which bands might be more free https://github.com/TheThingsNetwork/ttn/issues/119
finish power measurements (GPS on during sleep vs LCD on during sleep vs LORA on during sleep) and est battery life
make screen sleep behavior work
make screen advance only when a new node update arrives, a new text arrives or the user presses a button, turn off screen after a while
after reboot, channel number is getting reset to zero! fix!
send user and location events much less often
send location (or if not available user) when the user wakes the device from display sleep (both for testing and to improve user experience)
make real implementation of getNumOnlineNodes
very occasionally send our position and user packet based on the schedule in the radio info (if for nothing else so that other nodes update last_seen)
show real text info on the text screen
apply radio settings from android land
cope with nodes that have 0xff or 0x00 as the last byte of their mac
allow setting full radio params from android
add receive timestamps to messages, inserted by esp32 when message is received but then shown on the phone
update build to generate both board types
have node info screen show real info (including distance and heading)
blink the power led less often
have radiohead ISR send messages to RX queue directly, to allow that thread to block until we have something to send
move lora rx/tx to own thread and block on IO
keep our pseudo time moving forward even if we enter deep sleep (use esp32 rtc)
for non GPS equipped devices, set time from phone
GUI on oled hangs for a few seconds occasionally, but comes back
update local GPS position (but do not broadcast) at whatever rate the GPS is giving it
don't send our times to other nodes
don't trust times from other nodes
draw compass rose based off local walking track
add requestResponse optional bool - use for location broadcasts when sending tests
post sample video to signal forum
support non US frequencies
send pr https://github.com/ThingPulse/esp8266-oled-ssd1306 to tell them about this project
document rules for sleep wrt lora/bluetooth/screen/gps. also: if I have text messages (only) for the phone, then give a few seconds in the hopes BLE can get it across before we have to go back to sleep.
wake from light sleep as needed for our next scheduled periodic task (needed for gps position broadcasts etc)
turn bluetooth off based on our sleep policy
blink LED while in LS sleep mode
scrolling between screens based on press is busted
Use Neo-M8M API to put it in sleep mode (on hold until my new boards arrive)
update the prebuilt bins for different regulatory regions
don't enter NB state if we've recently talked to the phone (to prevent breaking syncing or bluetooth sw update)
have sw update prevent BLE sleep
manually delete characteristics/descs
leave lora receiver always on