meshtastic-firmware

Wykres commitów

Autor	SHA1	Wiadomość	Data
geeksville	5fbeaee0b0	eink kinda builds	2020-09-24 14:36:43 -07:00
geeksville	f1ca1ee3c0	okay basic support for @bigcorvus board is done	2020-08-29 12:46:42 -07:00
geeksville	dffb6c2f06	If display is on on the @BigCorvus board and we xmit the board browns out?	2020-08-28 17:38:23 -07:00
geeksville	7f214ffbb0	TFT kinda correct now - but slow because of bit banging	2020-08-28 15:33:33 -07:00
geeksville	d91ab5480f	begin support for TFT displays	2020-08-17 13:47:05 -07:00
geeksville	781077e799	Turn on buck converter for @BigCorvus board, now radio works	2020-08-17 11:42:19 -07:00
geeksville	22946b5e51	@BigCorvus board now kinda boots ###RTT Client: ----------------------------------------------- ###RTT Client: Connecting to J-Link RTT Server via localhost:19021 ... ###RTT Client: Connected. SEGGER J-Link V6.70c - Real time terminal output SEGGER J-Link ARM V9.6, SN=69663845 Process: JLinkGDBServerCLExe Emitting reboot packet for serial shell I2C device found at address 0x55 done Meshtastic swver=unset, hwver=unset Reset reason: 0x0 FIXME, call randomSeed ERROR: No UBLOX GPS found Hoping that NEMA might work RadioConfig reset! Initial packet id 1481765933, numPacketId 4294967295 No saved preferences found NODENUM=0xB18C3A4E, dbsize=1 Starting meshradio init... Set radio: name=Default, config=3, ch=6, power=17 SX1262 init result 0 sending owner !df5db18c3a4e/Unknown 3a4e/?4E Update DB node 0xB18C3A4E, rx_time=0 old user !df5db18c3a4e/Unknown 3a4e/?4E updating changed=0 user !df5db18c3a4e/Unknown 3a4e/?4E Adding packet record (id=0x5851F430 Fr0x4E To0xFF, WantAck0, HopLim3 Payload:User) enqueuing for send (id=0x5851F430 Fr0x4E To0xFF, WantAck0, HopLim3 encrypted) txGood=0,rxGood=0,rxBad=0 Starting low level send (id=0x5851F430 Fr0x4E To0xFF, WantAck0, HopLim3 encrypted) assert failed src/mesh/SX1262Interface.cpp: 102, virtual void SX1262Interface::setStandby(), test=err == ERR_NONE	2020-08-17 11:29:00 -07:00
geeksville	6b568ab2fb	add powerhold for @bigcorvus board	2020-08-16 14:50:04 -07:00
geeksville	67bad9a689	Add SX1262 to @BigCorvus board	2020-08-16 14:20:05 -07:00
geeksville	559a790286	Add @BigCorvus board support to build	2020-08-16 14:08:31 -07:00
geeksville	08e5bd728b	lorarelay wip	2020-08-16 14:07:01 -07:00
geeksville	0cfeeba2e2	add variant files by @BigCorvus	2020-08-16 13:25:24 -07:00
geeksville	cb1053850d	Oops - I mismerged at somepoint, restore correct PPR variant.h defs	2020-08-03 11:05:24 -07:00
geeksville	acbe8c159b	move rak815 variant to arduino repo	2020-07-10 12:38:11 -07:00
geeksville	5b07d454b1	WIP RAK815 now builds correctly	2020-07-10 11:29:32 -07:00
geeksville	b00a936f41	WIP RAK815 support	2020-07-10 11:02:29 -07:00
geeksville	477c62082d	E22 SX1262 module now works! Thanks mostly to an old github comment by @beegee-tokyo the fix was easy (comment here https://github.com/jgromes/RadioLib/issues/12#issuecomment-520450429) We now set DIO3 to 2.4 volts to power the oscillator inside the E22 module (undocumented in the E22 docs)	2020-06-15 14:38:09 -07:00
geeksville	4b5cfaf9ba	changes from bringing up PPR	2020-06-05 11:00:18 -07:00
geeksville	c12fb69ca2	update protos	2020-05-10 14:17:05 -07:00
geeksville	8b911aba7f	Cleanup build for NRF52 targets	2020-05-10 12:33:17 -07:00
geeksville	814c126e67	ugly WIP on switching to RadioLib, still need to set freq etc...	2020-04-29 14:54:03 -07:00
geeksville	a7d153abcb	CUSTOM GPIOs the SX1262MB2CAS shield when installed on the NRF52840-DK development board	2020-04-29 12:57:34 -07:00
geeksville	b8b503cb0a	Add starting point of PPR variants definition	2020-04-24 12:40:22 -07:00
geeksville	bb885a5110	add a variant based on the nrf52840-dk but with a RC clock. Because I was dumb and accidentally ran some code that configured gpio 0 as an output and that was enough to smoke the xtal that was preinstalled between P0.0 and P0.1.	2020-04-24 12:30:06 -07:00

24 Commity (86d6f887874fb15a39c628dddab13f4a22a725ec)