sp9unb
/
meshtastic-firmware
sforkowany z mirror/meshtastic-firmware
1
0
Forkuj 0
Kod Zgłoszenia Oczekujące zmiany Packages Projekty Wydania Wiki Aktywność
2 786 Commity
8 Gałęzie
195 Tagi
44 MiB
Wykres commitów

21 Commity (28af18389bf5a5dcb775de7d1c350fa2bb7a4e26)

Autor SHA1 Wiadomość Data
Kevin Hester c940d22a98 t-echo: enable nrfupload 2021-04-28 15:25:54 +08:00
Kevin Hester 2a9b2d3b29 official name for t-echo board 2021-04-27 10:21:54 +08:00
Kevin Hester 0a6d88a2d0 add not complete WIP for wizcore4600 2021-04-16 12:23:38 +08:00
Kevin Hester 328b24537f rak4631: builds but WIP 2021-04-11 13:33:27 +08:00
Vadim Furman c62863b1dc Merge from origin 2021-03-14 19:42:57 -07:00
Vadim Furman 98d878cdfe Port to lora_isp4520 board 2021-03-14 19:00:20 -07:00
Kevin Hester 51d0d0d6c5 begin new ttgo eink board 2021-01-16 09:57:55 +08:00
Kevin Hester 047df76373 move rev 0.1 of the ttgo eink board to eink0.1 2021-01-16 09:55:06 +08:00
Kevin Hester bbc36f7b6f switch to my new SD 7.2.0 S113 based bootloader 2020-10-31 12:22:20 +08:00
Kevin Hester 4ad562b9f4 The new 7.2.0 soft device works on nrf52833 2020-10-28 13:01:50 +08:00
Kevin Hester 5f2f3c94b9 PPR1 and allow boards to set lower or higher sx1262 power limits 2020-10-15 13:47:10 +08:00
Kevin Hester 965c2bda8d corvus2 board builds 2020-10-13 13:59:06 +08:00
geeksville 5fbeaee0b0 eink kinda builds 2020-09-24 14:36:43 -07:00
geeksville 22946b5e51 @BigCorvus board now kinda boots 
###RTT Client: -----------------------------------------------
###RTT Client: Connecting to J-Link RTT Server via localhost:19021 ...
###RTT Client: Connected.

SEGGER J-Link V6.70c - Real time terminal output
SEGGER J-Link ARM V9.6, SN=69663845
Process: JLinkGDBServerCLExe
Emitting reboot packet for serial shell
I2C device found at address 0x55
done
Meshtastic swver=unset, hwver=unset
Reset reason: 0x0
FIXME, call randomSeed
ERROR: No UBLOX GPS found
Hoping that NEMA might work
RadioConfig reset!
Initial packet id 1481765933, numPacketId 4294967295
No saved preferences found
NODENUM=0xB18C3A4E, dbsize=1
Starting meshradio init...
Set radio: name=Default, config=3, ch=6, power=17
SX1262 init result 0
sending owner !df5db18c3a4e/Unknown 3a4e/?4E
Update DB node 0xB18C3A4E, rx_time=0
old user !df5db18c3a4e/Unknown 3a4e/?4E
updating changed=0 user !df5db18c3a4e/Unknown 3a4e/?4E
Adding packet record (id=0x5851F430 Fr0x4E To0xFF, WantAck0, HopLim3 Payload:User)
enqueuing for send (id=0x5851F430 Fr0x4E To0xFF, WantAck0, HopLim3 encrypted)
txGood=0,rxGood=0,rxBad=0
Starting low level send (id=0x5851F430 Fr0x4E To0xFF, WantAck0, HopLim3 encrypted)
assert failed src/mesh/SX1262Interface.cpp: 102, virtual void SX1262Interface::setStandby(), test=err == ERR_NONE
 2020-08-17 11:29:00 -07:00
geeksville b00a936f41 WIP RAK815 support 2020-07-10 11:02:29 -07:00
geeksville 311d1a56b4 make a bare nrf52840dk build which will work for everyone 2020-07-09 20:05:39 -07:00
geeksville ed589727d6 Update NRF52 build to work again 2020-07-09 19:57:55 -07:00
geeksville 8b911aba7f Cleanup build for NRF52 targets 2020-05-10 12:33:17 -07:00
geeksville 814c126e67 ugly WIP on switching to RadioLib, still need to set freq etc... 2020-04-29 14:54:03 -07:00
geeksville b8b503cb0a Add starting point of PPR variants definition 2020-04-24 12:40:22 -07:00
geeksville bb885a5110 add a variant based on the nrf52840-dk but with a RC clock. 
Because I was dumb and accidentally ran some code that configured gpio 0
as an output and that was enough to smoke the xtal that was preinstalled
between P0.0 and P0.1.
 2020-04-24 12:30:06 -07:00