Merge branch 'master' of github.com:projecthorus/wenet into testing

start_docker_testing.sh

@@ -0,0 +1,116 @@
+# /usr/bin/env bash
+#
+# Helper script to start up the Wenet Docker image.
+#
+# This script is intended to be downloaded using wget or otherwise,
+# and modified prior to use.
+#
+
+# Your station callsign, which will be shown on https://ssdv.habhub.org
+# when receiving packets.
+# Make sure there is no space between the = and your callsign.
+MYCALL=CHANGEME
+
+# Receive Frequency (Hz)
+# The normal receive frequency used by Project Horus is 443.5 MHz
+RXFREQ=443500000
+
+# SDR Type. Set this to RTLSDR for RTL-SDR use or KA9Q for KA9Q-Radio use
+SDR_TYPE=RTLSDR
+
+# RTLSDR Device ID. Leave this at 0 if you don't want to use a particular device
+DEVICE=0
+
+# Receiver Gain (RTL-SDR only). Set this to 0 to use automatic gain control, otherwise if running a
+# preamplifier, you may want to experiment with lower gain settings to optimize
+# your receiver setup.
+# You can find what gain range is valid for your RTLSDR by running: rtl_test
+# A very rough figure that may work if you are running a preamp with ~20 dB gain is
+# 32.8 - your performance may vary!
+GAIN=0
+
+# Bias Tee Enable (1) or Disable (0) (RTL-SDR only)
+# Enable this is you are intending on powering a preamplifer via coax from your RTLSDR
+BIAS=0
+
+
+# Baud Rate & FSK Demod Oversampling Settings
+#
+# Default: 115177 baud 8x oversampling (Default using a RPi Zero W's UART)
+# Other parameters which *may* work, but are un-tested:
+# 9600 baud, 100x oversampling
+# 4800 baud, 200x oversampling
+#
+BAUD_RATE=115177
+OVERSAMPLING=8
+
+
+# UDP Payload Summary
+# Default: 0 (disabled)
+# Set this to a valid UDP port (55673 typically) to emit payload summary packets for use
+# with Chasemapper
+UDP_PORT=0
+
+# UDP Port used for Wenet inter-process communication.
+# If you are intenting on running more than one Wenet instance on the same computer
+# (e.g. multiple docker containers), use a different port for each instance.
+IMAGE_PORT=7890
+
+# HTTP server port for Web GUI.
+# If you are intenting on running more than one Wenet instance on the same computer
+# (e.g. multiple docker containers), use a different port for each instance.
+WEB_PORT=5003
+
+# Stop and remove any existing wenet instances
+echo "Stopping/Removing any existing Wenet instances..."
+docker stop wenet || true && docker rm wenet || true
+
+# Start the container!
+echo "Starting new Wenet instance..."
+if [ "$SDR_TYPE" = "RTLSDR" ] ; then
+	docker run -d \
+		--name wenet \
+		-e MYCALL=$MYCALL \
+		-e RXFREQ=$RXFREQ \
+		-e GAIN=$GAIN \
+		-e BIAS=$BIAS \
+		-e BAUD_RATE=$BAUD_RATE \
+		-e OVERSAMPLING=$OVERSAMPLING \
+		-e DEVICE=$DEVICE \
+		-e UDP_PORT=$UDP_PORT \
+		-e IMAGE_PORT=$IMAGE_PORT \
+		-e WEB_PORT=$WEB_PORT \
+		-e SDR_TYPE=$SDR_TYPE \
+		-v ~/wenet/rx_images/:/opt/wenet/rx_images/ \
+		--device /dev/bus/usb \
+		-p $WEB_PORT:$WEB_PORT \
+		--restart="always" \
+		ghcr.io/projecthorus/wenet:testing
+elif [ "$SDR_TYPE" = "KA9Q" ] ; then
+	docker run -d \
+		--name wenet \
+		-e MYCALL=$MYCALL \
+		-e RXFREQ=$RXFREQ \
+		-e GAIN=$GAIN \
+		-e BIAS=$BIAS \
+		-e BAUD_RATE=$BAUD_RATE \
+		-e OVERSAMPLING=$OVERSAMPLING \
+		-e DEVICE=$DEVICE \
+		-e UDP_PORT=$UDP_PORT \
+		-e IMAGE_PORT=$IMAGE_PORT \
+		-e WEB_PORT=$WEB_PORT \
+		-e SDR_TYPE=$SDR_TYPE \
+		-v ~/wenet/rx_images/:/opt/wenet/rx_images/ \
+		-v /var/run/dbus:/var/run/dbus \
+		-v /var/run/avahi-daemon/socket:/var/run/avahi-daemon/socket \
+		--device /dev/bus/usb \
+		--network host \
+		--restart="always" \
+		ghcr.io/projecthorus/wenet:testing
+
+else
+	echo "No valid SDR type specified! Please enter RTLSDR or KA9Q!"
+	exit 0
+fi
+
+echo "Navigate to http://localhost:5003/ in your web browser to see the Wenet interface!"