sane-dc25.5

sane-dc25(5)             SANE Scanner Access Now Easy             sane-dc25(5)

NAME

       sane-dc25 - SANE backend for Kodak DC20/DC25 Digital Cameras

DESCRIPTION

       The sane-dc25 library implements a SANE (Scanner Access Now Easy) back-
       end that provides access to Kodak DC20 and DC25 cameras.   At  present,
       only  the  DC25  has been tested, but since the code is based on a DC20
       interface program, it is likely to work for that model also.

DEVICE NAMES

       The current version of the backend only allows one camera  to  be  con-
       nected.  The device name is always "0".

CONFIGURATION

       The  contents of the dc25.conf specify the serial port and baud rate to
       use.  The baud rate specifies the maximum rate to use while downloading
       pictures.   (The  camera  is  always  initialized using 9600 baud, then
       switches to the higher rate).  On my 90MHz Pentium, I usually  have  no
       problems downloading at 115200 baud as long as the system is not exces-
       sively busy and the "interrupt-unmask flag" is set in  the  IDE  driver
       (hdparm -u1).  Supported baud rates are: 9600, 19200, 38400, 57600, and
       115200.

       The dumpinquiry line causes some information about  the  camera  to  be
       printed  to  stderr during startup.  Note:  This is not compatible with
       saned, so make sure you don't have any dumpinquiry  lines  if  you  are
       using saned (i.e. scanning on a remote machine using a network).

       Empty  lines  and  lines  starting with a hash mark (#) are ignored.  A
       sample configuration file is shown below:

              port=/dev/ttyS0
              # this is a comment
              baud=115200
              dumpinquiry

FILES

       /usr/local/etc/sane.d/dc25.conf
              The  backend  configuration  file  (see  also   description   of
              SANE_CONFIG_DIR below).

       /usr/local/lib/sane/libsane-dc25.a
              The static library implementing this backend.

       /usr/local/lib/sane/libsane-dc25.so
              The shared library implementing this backend (present on systems
              that support dynamic loading).

ENVIRONMENT

       SANE_CONFIG_DIR
              This environment variable specifies the list of directories that
              may contain the configuration file.  Under UNIX, the directories
              are separated by a colon (`:'), under OS/2, they  are  separated
              by a semi-colon (`;').  If this variable is not set, the config-
              uration file is searched in two default directories: first,  the
              current     working     directory     (".")    and    then    in
              /usr/local/etc/sane.d.  If the value of the environment variable
              ends  with  the  directory separator character, then the default
              directories are searched after the explicitly specified directo-
              ries.   For  example,  setting SANE_CONFIG_DIR to "/tmp/config:"
              would   result   in   directories   "tmp/config",    ".",    and
              "/usr/local/etc/sane.d" being searched (in this order).

       SANE_DEBUG_DC25
              If the library was compiled with debugging support enabled, this
              environment variable controls the debug level for this  backend.
              A  value of 128 requests maximally copious debug output; smaller
              levels reduce verbosity.

SEE ALSO

       sane(7)

AUTHOR

       Peter Fales, dc25-devel@fales-lorenz.net

BUGS

       Known bugs/limitations are:

       I haven't figured out how to  trigger  an  option  reload  following  a
       "scan."   This  causes problems when a new picture is snapped for exam-
       ple, the slider that is used to select the picture from the camera  may
       not be updated immediately.

       More  general  comments,  suggestions, and inquiries about frontends or
       SANE  should  go   to   the   SANE   Developers   mailing   list   (see
       http://www.sane-project.org/mailing-lists.html  for details).  You must
       be subscribed to the list, otherwise your mail won't  be  sent  to  the
       subscribers.

sane-backends 1.0.18             12 April 1999                    sane-dc25(5)