- return cmd status for reads of sensor options
* backend/canon_dr.c, doc/descriptions/canon_dr.desc: backend v26
- return cmd status for reads of sensor options
- allow rs to adjust read length for all bad status responses
- fix DR-2510C duplex deinterlacing code
- rewrite sane_read helpers to read until EOF
- update sane_start for scanners that dont use object_position
- dont call sanei_usb_clear_halt() if device is not open
- increase default buffer size to 4 megs
- set buffermode on by default
- hide modes and resolutions that DR-2510C lies about
- read_panel() logs front-end access to sensors instead of timing
- rewrite do_usb_cmd() to use remainder from RS info
* doc/desciptions/canon_dr.desc: backend v24, update DR-2510C comment
* backend/pixma_bjnp.c
- silenced some debug statements during scanner detections
- increased timeouts to 20 seconds as 10 seconds is apparently
- not enough for the combination of a Mac and an MX850.
- rewrite all image data processing code
- handle more image interlacing formats
- re-enable binary mode on some scanners
- limit some machines to full-width scanning
* doc/desciptions/canon_dr.desc: v23, improved comments
- improved macros for inquiry and set window
- shorten inquiry vpd length to match windows driver
- remove status-length config option
- add padded-read config option
- rewrite do_usb_cmd to pad reads and calloc/copy buffers
* backend/canon_dr.conf.in: s/status-length/padded-read/g
- pad gray deinterlacing area for DR-2510C
- override tl_x and br_x for fixed width scanners
* doc/descriptions/canon_dr.desc: backend v19, update comments
- add byte-oriented duplex interlace code
- add RRGGBB color interlace code
- add basic support for DR-2580C, DR-2050C, DR-2080C, DR-2510C
- add more unknown setwindow bits
- add support for 16 byte status packets
- clean do_usb_cmd error handling (call reset more often)
- set status packet size from config file
- rewrite config file parsing to reset options after each scanner
- add config options for vendor, model, version
- dont call inquiry if those 3 options are set
- remove default config file from code
- add initial gray deinterlacing code for DR-2510C
- rename do_usb_reset to do_usb_clear
* doc/descriptions/canon_dr.desc: backend v18, update model status
* backend/canon_dr.conf.in: added better comments and new options
* backend/pixma_bjnp.c backend/pixma_bjnp.h
backend/pixma_bjnp_private.h backend/pixma_io_sanei.c:
Make bjnp protocol more resilient against packet loss and corruption
Changed timeout for all responses to be at least 10 seconds
Send all broadcasts for scanner detection 5 times
Made sure scanners are added to device list only once
Changed device-id for bjnp so it uses scanner hostname/ip-address
instead of mac address as this is more human friendly.
To make room, use scanner model instead of USB-id (which is bogus
for network scanners
to sane-config missed during fix to stop using LIBS to link everything.
Add back in code to move LDFLAGS out of $GPHOTO2_LIBS and into
GPHOTO2_LDFLAGS.
- rewrite of calibration process to make it more robust and accurate
- untested full support for hp3670
- untested support for 50, 100 and 300 uncalibrated scans for hp2400
- use of id for device parts descriptions instead of using fixed
place in tables
- SCAN_MODE_* defines to clean up code
Global replace of u_int??_t with C9x standard based uintxx_t
in order to remove some tricky and overlapping portability logic
from acinclude.m4 and leave it in only m4/stdint.m4.
Nicolas Martin