sane-project-backends/backend/genesys.conf.in

# genesys.conf: Configuration file for Genesys Logic GL646 and GL841 based scanners

#
# scanners that are not yet supported
# uncomment them only for developpment purpose
#

# UMAX Astra 4500 and Avision iVina 1600
#usb 0x0638 0x0a10

# Hewlett Packard ScanJet 2400c
usb 0x03f0 0x0a01

# Hewlett Packard ScanJet 3670c/3690c
usb 0x03f0 0x1405

# Plustek OpticPro ST24
#usb 0x07b3 0x0601

# Syscan DocketPort 465
#usb 0x0a82 0x4802

#
# supported scanners
#

# Medion MD5345/MD6228/MD6471
usb 0x0461 0x0377

# Hewlett Packard ScanJet 2300c
usb 0x03f0 0x0901

# Canon LiDE 35/40/50
usb 0x04a9 0x2213

# Canon LiDE 60
usb 0x04a9 0x221c

# Canon LiDE 80
usb 0x04a9 0x2214

# Canon 4400F
usb 0x04a9 0x2228

# Canon LiDE 100
usb 0x04a9 0x1904

# Canon LiDE 110
usb 0x04a9 0x1909

# Canon LiDE 200
usb 0x04a9 0x1905

# Canon 5600F
usb 0x04a9 0x1906

# Canon LiDE 700F
usb 0x04a9 0x1907

# Canon LiDE 210
usb 0x04a9 0x190a

# Canon 5600f
usb 0x04a9 0x1906

# Visioneer Strobe XP200
usb 0x04a7 0x0426

# Visioneer Strobe XP300
usb 0x04a7 0x0474

# Ambir/Syscan DocketPort 665
usb 0x0a82 0x4803

# Visioneer Roadwarrior
usb 0x04a7 0x0494

# Visioneer XP100 rev 3
usb 0x04a7 0x049b

#Pentax DSmobile 600
usb 0x0a17 0x3210
usb 0x04f9 0x2038

# Syscan DocketPort 467
usb 0x1dcc 0x4812

# Syscan DocketPort 485
usb 0x0a82 0x4800

# DCT DocketPort 487
usb 0x1dcc 0x4810

# Syscan/Ambir DocketPort 685
usb 0x0a82 0x480c

# Visioneer OneTouch 7100
usb 0x04a7 0x0229

# Xerox Travel Scanner 100
usb  0x04a7 0x04ac

# Panasonic KV-SS080
usb 0x04da 0x100f

# Hewlett Packard ScanJet 4850C
usb 0x03f0 0x1b05

# Hewlett Packard ScanJet G4010
usb 0x03f0 0x4505

# Hewlett Packard ScanJet G4050
usb 0x03f0 0x4605

# Plustek OpticBook 3600
usb 0x07b3 0x0900

# Primax Electronics, Ltd Xerox 2400 Onetouch
usb 0x0461 0x038b

#Hewlett Packard ScanJet N6310
usb 0x03f0 0x4705

# Canon Image Formula 101
usb 0x1803 0x162e

# Plustek OpticBook 3800
usb 0x07b3 0x1300
- added genesys backend from experimental area 2005-06-27 20:07:45 +00:00			`# genesys.conf: Configuration file for Genesys Logic GL646 and GL841 based scanners`

			`#`
			`# scanners that are not yet supported`
			`# uncomment them only for developpment purpose`
			`#`

			`# UMAX Astra 4500 and Avision iVina 1600`
			`#usb 0x0638 0x0a10`

			`# Hewlett Packard ScanJet 2400c`
- rewrite of gl646 internals to enable easy addition of new models - rewrite of calibration process to make it more robust and accurate - untested full support for hp3670 - untested support for 50, 100 and 300 uncalibrated scans for hp2400 - use of id for device parts descriptions instead of using fixed place in tables - SCAN_MODE_* defines to clean up code 2009-02-27 12:37:16 +00:00			`usb 0x03f0 0x0a01`
- added genesys backend from experimental area 2005-06-27 20:07:45 +00:00
update HP3690 status to supported 2010-09-13 04:19:47 +00:00			`# Hewlett Packard ScanJet 3670c/3690c`
- rewrite of gl646 internals to enable easy addition of new models - rewrite of calibration process to make it more robust and accurate - untested full support for hp3670 - untested support for 50, 100 and 300 uncalibrated scans for hp2400 - use of id for device parts descriptions instead of using fixed place in tables - SCAN_MODE_* defines to clean up code 2009-02-27 12:37:16 +00:00			`usb 0x03f0 0x1405`
- added genesys backend from experimental area 2005-06-27 20:07:45 +00:00
			`# Plustek OpticPro ST24`
			`#usb 0x07b3 0x0601`

Add basic support for Visioneer XP100 rev 3 and USB IDs for Syscan DocketPort 465 2009-03-19 22:27:53 +00:00			`# Syscan DocketPort 465`
			`#usb 0x0a82 0x4802`
Bumped build number. Changed scanner's name to Canon LiDE 35/40/50. Added Canon LiDE LiDE 60. This scanner is still commented out in genesys.conf. Removed comment sign for Canon LiDE 35/40/50 in genesys.conf. 2005-11-20 13:59:39 +00:00
- added genesys backend from experimental area 2005-06-27 20:07:45 +00:00			`#`
			`# supported scanners`
			`#`

			`# Medion MD5345/MD6228/MD6471`
			`usb 0x0461 0x0377`

			`# Hewlett Packard ScanJet 2300c`
			`usb 0x03f0 0x0901`
Bumped build number. Changed scanner's name to Canon LiDE 35/40/50. Added Canon LiDE LiDE 60. This scanner is still commented out in genesys.conf. Removed comment sign for Canon LiDE 35/40/50 in genesys.conf. 2005-11-20 13:59:39 +00:00
			`# Canon LiDE 35/40/50`
			`usb 0x04a9 0x2213`

Enabled Canon LiDE 60 which was disabled for safety reasons. Bugs are fixed now. 2005-12-06 10:34:15 +00:00			`# Canon LiDE 60`
			`usb 0x04a9 0x221c`
- add support for uncalibrated scan for Visioneer Strobe XP200 - button support for MD5345, HP2300 and XP200 2009-01-19 05:46:43 +00:00
add LiDE 80 device description 2013-10-11 04:34:06 +00:00			`# Canon LiDE 80`
			`usb 0x04a9 0x2214`

initial Canonscan 4400F work - add 4400F to devices - add settings for 100 dpi scan 2012-09-23 19:15:39 +00:00			`# Canon 4400F`
			`usb 0x04a9 0x2228`

before LiDE 100 init 2010-04-30 12:26:31 +00:00			`# Canon LiDE 100`
			`usb 0x04a9 0x1904`

add new gl124 asic create a place holder for low level commands move low level functions to genesys_low.c GL124 progresses enable genesys_low debug and add DAC for LiDE 110 gl124 WIP - gl847 cleanups - genesys_low refactor - gl124 starting version GL124 WIP - read scancnt/fedcnt,valid words coded - memory layout coded LiDE110 WIP GL 124 WIP - definition and use of get/set double/triple - define register names all mods done, ready to test set fe OK GL124 WIP : ready to test scans GL124 WIP GL124 WIP - fixed analog fe issue: don't put afe regs in global set GL124 : first light at 300 dpi GL124 WIP - 300 and 600 uncalibrated mostly ok (x coordinate rounding) - 150 and 75 OK x-wise, y to be solved solved rounding errors for gl124 re-add 400, 200 and 100 dpi modes GL124 : tous x dpi OK before adding line cropping GL124 : line cropping almost finished GL124 WIP : working line deletion compute step rework GL124 WIP : high speed table for dpi <= 300 move to scan area working line skipping fix new slope table for 600 dpi base geometry and movement tuned GL124 WIP : shading calibration almost working working 600 dpi shading GL124 : working shading calibration for all modes but 1200 dpi working 1200 dpi shading beta 1 of GL124 support last tuning update genesys.desc for LiDE 110 motor slope and start area tuning shading coefficient computing clean up add support for GL124 based CanoScan LiDE 110 feed almost OK up to 300 dpi feeding is fixed all issues fixed 2010-11-06 20:12:56 +00:00			`# Canon LiDE 110`
			`usb 0x04a9 0x1909`

WIP setup optical regs ~OK 2010-04-25 19:32:44 +00:00			`# Canon LiDE 200`
			`usb 0x04a9 0x1905`

misc genesys updates - add or tune entry for 5600f/700f - fix HP2300 warming up problem 2010-12-28 20:01:46 +00:00			`# Canon 5600F`
			`usb 0x04a9 0x1906`

			`# Canon LiDE 700F`
			`usb 0x04a9 0x1907`

add an device entry for LiDE 210 2010-12-15 05:24:55 +00:00			`# Canon LiDE 210`
			`usb 0x04a9 0x190a`

add an entry for Canoscan 5600F in the genesys backend 2010-08-02 04:32:11 +00:00			`# Canon 5600f`
			`usb 0x04a9 0x1906`

- add support for uncalibrated scan for Visioneer Strobe XP200 - button support for MD5345, HP2300 and XP200 2009-01-19 05:46:43 +00:00			`# Visioneer Strobe XP200`
			`usb 0x04a7 0x0426`
Add support for Ambir/Syscan DocketPORT 665 2009-02-28 18:01:50 +00:00
			`# Visioneer Strobe XP300`
			`usb 0x04a7 0x0474`

			`# Ambir/Syscan DocketPort 665`
			`usb 0x0a82 0x4803`
Add support for Visioneer Roadwarrior 2009-02-28 18:03:44 +00:00
			`# Visioneer Roadwarrior`
			`usb 0x04a7 0x0494`
Add basic support for Visioneer XP100 rev 3 and USB IDs for Syscan DocketPort 465 2009-03-19 22:27:53 +00:00
			`# Visioneer XP100 rev 3`
			`usb 0x04a7 0x049b`
Add Pentax DSmobile 600 Thanks go to Jack McGill for providing the model specific settings. 2009-05-19 14:24:59 +00:00
			`#Pentax DSmobile 600`
			`usb 0x0a17 0x3210`
add new gl124 asic create a place holder for low level commands move low level functions to genesys_low.c GL124 progresses enable genesys_low debug and add DAC for LiDE 110 gl124 WIP - gl847 cleanups - genesys_low refactor - gl124 starting version GL124 WIP - read scancnt/fedcnt,valid words coded - memory layout coded LiDE110 WIP GL 124 WIP - definition and use of get/set double/triple - define register names all mods done, ready to test set fe OK GL124 WIP : ready to test scans GL124 WIP GL124 WIP - fixed analog fe issue: don't put afe regs in global set GL124 : first light at 300 dpi GL124 WIP - 300 and 600 uncalibrated mostly ok (x coordinate rounding) - 150 and 75 OK x-wise, y to be solved solved rounding errors for gl124 re-add 400, 200 and 100 dpi modes GL124 : tous x dpi OK before adding line cropping GL124 : line cropping almost finished GL124 WIP : working line deletion compute step rework GL124 WIP : high speed table for dpi <= 300 move to scan area working line skipping fix new slope table for 600 dpi base geometry and movement tuned GL124 WIP : shading calibration almost working working 600 dpi shading GL124 : working shading calibration for all modes but 1200 dpi working 1200 dpi shading beta 1 of GL124 support last tuning update genesys.desc for LiDE 110 motor slope and start area tuning shading coefficient computing clean up add support for GL124 based CanoScan LiDE 110 feed almost OK up to 300 dpi feeding is fixed all issues fixed 2010-11-06 20:12:56 +00:00			`usb 0x04f9 0x2038`
calibration and configuration fix - fixed genesys.conf for 2 missing models - updated desc file - definitive fix for shhetfed calibration 2009-11-16 20:28:27 +00:00
add docket port 467 model 2009-11-25 19:59:10 +00:00			`# Syscan DocketPort 467`
			`usb 0x1dcc 0x4812`

calibration and configuration fix - fixed genesys.conf for 2 missing models - updated desc file - definitive fix for shhetfed calibration 2009-11-16 20:28:27 +00:00			`# Syscan DocketPort 485`
			`usb 0x0a82 0x4800`

			`# DCT DocketPort 487`
			`usb 0x1dcc 0x4810`
add support for Ambir/Syscan DS685 2009-12-05 06:23:40 +00:00
			`# Syscan/Ambir DocketPort 685`
			`usb 0x0a82 0x480c`
add visioneer 7100 support - add visioneer 7100 support, patch by Jack McGill 2010-01-19 05:04:04 +00:00
			`# Visioneer OneTouch 7100`
small cleanup 2010-01-19 20:34:36 +00:00			`usb 0x04a7 0x0229`
add Xerox Travel Scanner 100 2010-01-30 13:15:32 +00:00
			`# Xerox Travel Scanner 100`
			`usb 0x04a7 0x04ac`
first gl843 steps - clone gl847 - add KV-SS080 entry with provisional values 2010-07-20 20:04:11 +00:00
			`# Panasonic KV-SS080`
			`usb 0x04da 0x100f`
about to reach first light state - fe is set - slope tables are written (but not table 2) - compile warnings are fixed 2010-07-30 04:47:01 +00:00
add HP 4850c as an untested gl843 device 2011-11-19 08:50:44 +00:00			`# Hewlett Packard ScanJet 4850C`
			`usb 0x03f0 0x1b05`

add test value for G4010 2010-09-28 19:36:02 +00:00			`# Hewlett Packard ScanJet G4010`
			`usb 0x03f0 0x4505`

about to reach first light state - fe is set - slope tables are written (but not table 2) - compile warnings are fixed 2010-07-30 04:47:01 +00:00			`# Hewlett Packard ScanJet G4050`
			`usb 0x03f0 0x4605`
add opticbook 3600 to genesys.conf.in 2010-12-27 05:48:15 +00:00
			`# Plustek OpticBook 3600`
			`usb 0x07b3 0x0900`
add Xerox 2400 onetouch model 2011-04-20 19:42:49 +00:00
			`# Primax Electronics, Ltd Xerox 2400 Onetouch`
			`usb 0x0461 0x038b`
update HP N6310 description 2011-11-20 07:05:39 +00:00
			`#Hewlett Packard ScanJet N6310`
			`usb 0x03f0 0x4705`
genesys backend update - groundwork for gl846 support - asic init rework - several refactors 2013-01-28 21:04:37 +00:00
			`# Canon Image Formula 101`
			`usb 0x1803 0x162e`
experimental code for GL845 based Opticbook 3800 - add GL845 ASIC which is almost identical to the GL846 - add Opticbook 3800 to genesys backend 2013-06-26 04:51:55 +00:00
			`# Plustek OpticBook 3800`
			`usb 0x07b3 0x1300`