Flash sectors should start counting at 0 for each bank. This commit makes
sure that is the case on all H5 and H7 MCUs, by using `get_page()` instead
of `flash_get_sector_info()`.
Signed-off-by: Damien George <damien@micropython.org>
An erase sector sits in a given flash bank and some MCUs have two flash
banks. If trying to erase a range of sectors and that range crosses from
one flash bank into the next, the original implementation of
`flash_erase()` would not handle this case and would do the wrong thing.
This commit changes `flash_erase()` to only erase a single sector, which
sidesteps the need to handle flash-bank-crossing. Most callers of this
function only need to erase a single sector anyway.
Signed-off-by: Damien George <damien@micropython.org>
Newer STM32 parts have homogeneous flash layout, and in this case the MCU
configuration and page/sector calculation can be simplified. The affected
functions are `flash_is_valid_addr()` and `flash_get_sector_info()`, which
are now simpler for homogeneous flash.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds initial support for STM32H5xx MCUs. The following
features have been confirmed to be working on an STM32H573:
- UART over REPL and USB CDC
- USB CDC and MSC
- internal flash filesystem
- machine.Pin
- machine.SPI transfers with DMA
- machine.ADC
- machine.RTC
- pyb.LED
- pyb.Switch
- pyb.rng
- mboot
Signed-off-by: Damien George <damien@micropython.org>
This was added by mistake in 8f68e26f79 when
adding support for G4 MCUs, which does not using this get_bank() function.
FLASH_OPTR_DBANK is only defined on G4 and L4 MCUs, so on H7 this
FLASH_BANK_2 code was being wrongly excluded.
Signed-off-by: Damien George <damien@micropython.org>
This commit adds support for the STM32G4 series of MCUs, and a board
definition for NUCLEO_G474RE. This board has the REPL on LPUART1 which is
connected to the on-board ST-link USB-UART.
This commit is based upon prior work of @dpgeorge and @koendv.
MCU support for the STM32H7A3 and B3 families MCUs:
- STM32H7A3xx
- STM32H7A3xxQ (SMPS)
- STM32H7B3xx
- STM32H7B3xxQ (SMPS)
Support has been added for the STM32H7B3I_DK board.
Signed-off-by: Jan Staal <info@janstaal.com>
This is needed to moderate concurrent access to the internal flash, as
while an erase/write is in progress execution will stall on the wireless
core due to the bus being locked.
This implements Figure 10 from AN5289 Rev 3.
Signed-off-by: Jim Mussared <jim.mussared@gmail.com>
This commit makes the low-level flash C functions usable by code other than
flashbdev.c (eg by mboot). Changes in this commit are:
- flash_erase() and flash_write() now return an errno error code, a
negative value on error.
- flash_erase() now automatically locks the flash, as well as unlocking it.
- flash_write() now automatically unlocks the flash, as well as locking it.
- flashbdev.c is modified for the above changes.
Signed-off-by: Damien George <damien@micropython.org>
This new series of MCUs is similar to the L4 series with an additional
Cortex-M0 coprocessor. The firmware for the wireless stack must be managed
separately and MicroPython does not currently interface to it. Supported
features so far include: RTC, UART, USB, internal flash filesystem.
The CMSIS files for the STM32 range provide macros to distinguish between
the different MCU series: STM32F4, STM32F7, STM32H7, STM32L4, etc. Prefer
to use these instead of custom ones.
This is to keep the top-level directory clean, to make it clear what is
core and what is a port, and to allow the repository to grow with new ports
in a sustainable way.