The parts that are generic are added to py/ so they can be used by other
ports that use CMake.
py/usermod.cmake:
* Creates a usermod target to hang user C/CXX modules from.
* Gathers sources from user C/CXX modules and libs for QSTR scan.
ports/rp2/CMakeLists.txt:
* Includes py/usermod.cmake.
* Links the resulting usermod library to the MicroPython target.
py/mkrules.cmake:
Add cxxflags to qstr.i.last custom command for CXX modules:
* MICROPY_CPP_FLAGS so CXX modules will find includes.
* -DNO_QSTR to fix fatal error missing "genhdr/qstrdefs.generated.h".
Usage:
The rp2 port can be linked against user C modules by running:
make USER_C_MODULES=/path/to/module/micropython.cmake
CMake will print a list of included modules.
Co-authored-by: Graham Sanderson <graham.sanderson@raspberrypi.org>
Co-authored-by: Michael O'Cleirigh <michael.ocleirigh@rivulet.ca>
Signed-off-by: Phil Howard <phil@pimoroni.com>
This commit simplifies and cleans up the bare-arm port, and adds just
enough system and library code to make it execute on an STM32F405 MCU.
The mpconfigport.h configuration is simplified to just specify those
configuration values that are different from the defaults. And the
addition of -fdata-sections and -ffunction-sections means the final
firmware is smaller than it previously was, by about 4200 bytes.
A README is also added.
Signed-off-by: Damien George <damien@micropython.org>
mp_printf should be used to print the prefix because it's also used in
mp_bytecode_print2 (otherwise, depending on the system, different output
streams may be used).
Also print the current thread state when threading is enabled to easily see
which thread executes what opcode.
Signed-off-by: Damien George <damien@micropython.org>
This helps to reduce memory fragmentation, by freeing the heap data as soon
as it is not needed. It also helps the compiler keeps a reference to the
beginning of both arrays, which need to be traceable by the GC (otherwise
some compilers may optimise this reference to something else).
Signed-off-by: Damien George <damien@micropython.org>
The GNU Make dir command uses spaces as item separator so it does not
work for e.g building the STM32 port on Cygwin with a default Arm
installation in "c:/program files (x86)/GNU Arm Embedded Toolchain".
Fix by using POSIX dirname on a quoted path instead.
Add most formatting-only commits to this file so that when used with
git blame, these commits are excluded and the output shows only the
interesting bits.
When UART is used for REPL and the MCU frequency is changed, the UART
has to be re-initialised. Besides that the UART may have to be recreated
after a frequency change, but with USB REPL this is not a problem.
Thanks to @HermannSW for spotting and providing the change.
Using the standard machine.freq().
The safe ranges tested were 10 and 12-270MHz, at which USB REPL still
worked. Requested settings can be checked with the script:
pico-sdk/src/rp2_common/hardware_clocks/scripts/vcocalc.py. At frequencies
like 300MHz the script still signaled OK, but USB did not work any more.
sm.get(buf) was waiting for one item more than the length of the supplied
buffer. Even if this item was not stored, sm_get would block trying to get
an item from the RX fifo.
As part of the fix, the edge case for a zero length buffer was moved up to
the section where the function arguments are handled. In case of a zero
length buffer, sm.get() now returns immediately that buffer.
The bitmasks supplied for initialization of out/set/sideset were only 8 bit
instead of 32. This resulted in an error, that not more than 8 consecutive
pins would get initialized.
Fixes issue #6933.
From a version numbering point of view this is a downgrade (2.17.0 ->
2.16.x). However the latest commit for version 2.17.0 is from March 2019
and no further minor release happened after 2.17.0. This version is EOL.
2.16.x though is still actively maintained as a long term release, hence
security and stability fixes are still being backported, including
compatibility with upcoming compiler releases.
This allows the user to enable wake-up sources using the EWUP bits, on F7
MCUs.
Disabling the wake-up sources while clearing the wake-up flags follows the
reference manual and ST examples.
state.reset_mode is updated by `MICROPY_BOARD_BEFORE_SOFT_RESET_LOOP` but
not passed to `init_flash_fs`, and so factory reset is not executed on
boards that do not have a bootloader. This bug was introduced by
4c3976bbcaFixes#6903.
A corrupt filesystem may lead to a request for a block which is out of
range of the block device limits. Return an error instead of passing the
request down to the lower layer.
Two of the defaults have also changed in this commit:
- MICROPY_HW_RFCORE_BLE_LSE_SOURCE changed from 1 to 0, which configures
the LsSource to be LSE (needed due to errata 2.2.1).
- MICROPY_HW_RFCORE_BLE_VITERBI_MODE changed from 0 to 1, which enables
Viterbi mode, following all the ST examples.
Signed-off-by: Damien George <damien@micropython.org>
Instead of raising a ZeroDivisionError, this tool now just skips any
elements in the DFU file that have zero size.
Signed-off-by: Damien George <damien@micropython.org>
These ports already have uzlib enabled so this additional ubinascii.crc32
function only costs about 90 bytes of flash.
Signed-off-by: Damien George <damien@micropython.org>
This allows a port to specify a custom qstrdefsport.h file, the same as the
QSTR_DEFS variable in a Makefile.
Signed-off-by: Damien George <damien@micropython.org>
Add LPUART1 as a standard UART. No low power features are supported, yet.
LPUART1 is enabled as the next available UART after the standard U(S)ARTs:
STM32WB: LPUART1 = UART(2)
STM32L0: LPUART1 = UART(6)
STM32L4: LPUART1 = UART(6)
STM32H7: LPUART1 = UART(9)
On all ports: LPUART1 = machine.UART('LP1')
LPUART1 is enabled by defining MICROPY_HW_LPUART1_TX and
MICROPY_HW_LPUART1_RX in mpconfigboard.h.
Signed-off-by: Chris Mason <c.mason@inchipdesign.com.au>
Phil Howard