kopia lustrzana https://github.com/peterhinch/micropython-nano-gui
Add commensts to color_setup/st7789_ttgo.py
rodzic
637f1e1521
commit
3be1afca98
|
@ -11,32 +11,52 @@
|
|||
# https://github.com/Xinyuan-LilyGO/TTGO-T-Display/blob/master/image/pinmap.jpg
|
||||
# https://github.com/Xinyuan-LilyGO/TTGO-T-Display/blob/master/schematic/ESP32-TFT(6-26).pdf
|
||||
|
||||
# Demo of initialisation procedure designed to minimise risk of memory fail
|
||||
# when instantiating the frame buffer. The aim is to do this as early as
|
||||
# possible before importing other modules.
|
||||
|
||||
# WIRING (TTGO T-Display pin nos and names).
|
||||
# Pinout of TFT Driver
|
||||
# WIRING (TTGO T-Display pin numbers and names).
|
||||
# Pinout of TFT Driver
|
||||
# ST7789 ESP32
|
||||
# TFT_MISO N/A
|
||||
TFT_MOSI = 19
|
||||
TFT_SCLK = 18
|
||||
TFT_CS = 5
|
||||
TFT_DC = 16
|
||||
TFT_RST = 23
|
||||
TFT_BL = 4 # LEDK = BL Display backlight control pin
|
||||
TFT_MOSI = 19 # (SDA on schematic pdf) SPI interface output/input pin.
|
||||
TFT_SCLK = 18 # This pin is used to be serial interface clock.
|
||||
TFT_CS = 5 # Chip selection pin, low enable, high disable.
|
||||
TFT_DC = 16 # Display data/command selection pin in 4-line serial interface.
|
||||
TFT_RST = 23 # This signal will reset the device,Signal is active low.
|
||||
TFT_BL = 4 # (LEDK on schematic pdf) Display backlight control pin
|
||||
|
||||
ADC_IN = 34
|
||||
ADC_EN = 14 # PWR_EN = ADC_EN is the ADC detection enable port
|
||||
ADC_IN = 34 # Measuring battery or USB voltage, see comment below
|
||||
ADC_EN = 14 # (PWR_EN on schematic pdf) is the ADC detection enable port
|
||||
|
||||
BUTTON1 = 35 # right of the USB connector
|
||||
BUTTON2 = 0 # left of the USB connector
|
||||
|
||||
#I2C_SDA = 19
|
||||
#I2C_SCL = 18
|
||||
# ESP32 pins, free for use in user applications
|
||||
#I2C_SDA = 21 # hardware ID 0
|
||||
#I2C_SCL = 22
|
||||
|
||||
#DAC1 25
|
||||
#DAC2 26
|
||||
#UART2TXD = 17
|
||||
|
||||
#GPIO2 = 2
|
||||
#GPIO15 = 15
|
||||
#GPIO13 = 13
|
||||
#GPIO12 = 12
|
||||
|
||||
#GPIO37 = 37
|
||||
#GPIO38 = 38
|
||||
#UART1TXD = 4
|
||||
#UART1RXD = 5
|
||||
#GPIO18 = 18
|
||||
#GPIO19 = 19
|
||||
#GPIO17 = 17
|
||||
|
||||
#DAC1 = 25
|
||||
#DAC2 = 26
|
||||
|
||||
# Input only pins
|
||||
#GPIO36 = 36 # input only
|
||||
#GPIO39 = 39 # input only
|
||||
|
||||
# Demo of initialisation procedure designed to minimise risk of memory fail
|
||||
# when instantiating the frame buffer. The aim is to do this as early as
|
||||
# possible before importing other modules.
|
||||
|
||||
from machine import Pin, SPI, ADC
|
||||
import gc
|
||||
|
@ -52,7 +72,22 @@ pbl = Pin(TFT_BL, Pin.OUT, value=1)
|
|||
gc.collect() # Precaution before instantiating framebuf
|
||||
# Conservative low baudrate. Can go to 62.5MHz.
|
||||
spi = SPI(1, 30_000_000, sck=Pin(TFT_SCLK), mosi=Pin(TFT_MOSI))
|
||||
|
||||
''' TTGO
|
||||
v +----------------+
|
||||
40 | | |
|
||||
^ | +------+ | pin 36
|
||||
| | | | |
|
||||
| | | | |
|
||||
240 | | | | |
|
||||
| | | | |
|
||||
| | | | |
|
||||
v | +------+ |
|
||||
40 | | | Reset button
|
||||
^ +----------------+
|
||||
>----<------>----<
|
||||
52 135 xx
|
||||
BUTTON2 BUTTON1
|
||||
'''
|
||||
# Right way up landscape: defined as top left adjacent to pin 36
|
||||
ssd = SSD(spi, height=135, width=240, dc=pdc, cs=pcs, rst=prst, disp_mode=LANDSCAPE, display=TDISPLAY)
|
||||
# Normal portrait display: consistent with TTGO logo at top
|
||||
|
@ -65,11 +100,11 @@ ssd = SSD(spi, height=135, width=240, dc=pdc, cs=pcs, rst=prst, disp_mode=LANDSC
|
|||
# adc_in = ADC(Pin(ADC_IN))
|
||||
# adc_en.value(0)
|
||||
'''
|
||||
Set PWR_EN to "1" and read voltage in BAT_ADC,
|
||||
Set ADC_EN to "1" and read voltage in BAT_ADC,
|
||||
if this voltage more than 4.3 V device have powered from USB.
|
||||
If less then 4.3 V - device have power from battery.
|
||||
To save battery you can set PWR_EN to "0" and in this case the USB converter
|
||||
To save battery you can set ADC_EN to "0" and in this case the USB converter
|
||||
will be power off and do not use your battery.
|
||||
When you need to measure battery voltage first set PWR_EN to "1",
|
||||
measure voltage and then set PWR_EN back to "0" for save battery.
|
||||
When you need to measure battery voltage first set ADC_EN to "1",
|
||||
measure voltage and then set ADC_EN back to "0" for save battery.
|
||||
'''
|
||||
|
|
Ładowanie…
Reference in New Issue