* Initial support for the ThinkNode M5
* Update variants/esp32s3/ELECROW-ThinkNode-M5/platformio.ini
Co-authored-by: Austin <vidplace7@gmail.com>
* Cleanup variant.h for Elecrow Thinknode M5
* Properly detect battery voltage
* Turn backlight off when screen sleeps
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Austin <vidplace7@gmail.com>
* feat: event mode - limit smart position updates to at most every 5m
* fix: convert 600 to 600000ms for 5min threshold
* fix: correct 5min threshold to 300000ms
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* T-watch screen misalignment fix
* Trunk fix
* Rember Last Receipient Node or channel
When a new freetext or preset message is sent and a destination is selected, the next message would forget the previously selected destination and would need to be selected again. With this fix it will remember the last destination selected until changed again.
* Fix for reply function to remember last messaged
* trunk check
---------
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
Co-authored-by: Jason P <applewiz@mac.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
TinyGPS Fix Quality has this information:
0 - fix not available,
1 - GPS fix,
2 - Differential GPS fix (values above 2 are 2.3 features)
3 = PPS fix
4 = Real Time Kinematic
5 = Float RTK
6 = estimated (dead reckoning)
7 = Manual input mode
8 = Simulation mode
the previous Airoha code would allow quality >0 , which includes
estimated positions. These wouldn't be passed through to the mesh
due to other checks, but would affect the Airoha GPS_FIX_HOLD_TIME
calculations.
Changes the calculation to 1 >= quality <=5 .
Expertly triaged by @philon- , turning off wifi using the HTTP API
did not work. That was because we only served the HTTP API if Wifi
was deemed to be available, but mid-way through turning it off Wifi
was still available, but the configuration we were checking said it wasn't.
This patch introduces an additional way the system can determine if Wifi
is available, by referring to the WiFi.status(). This means that in that
limbo state where Wifi has been set to be turned off, but the configuration
has not been saved and it is still up, the HTTP API will stay up long enough
to save the configuration.
Fixes https://github.com/meshtastic/firmware/issues/6965
* treewide: make 'ifdef DEBUG_PORT' guards also take into account DEBUG_MUTE
* stm32wl: Add a guard against having debug prints turned on without PIO_FRAMEWORK_ARDUINO_NANOLIB_FLOAT_PRINTF defined
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Clear position on GPS deactivation, unless using fixed position
As reported by @dreimal8 , and confirmed by @tuxmobil , when using
and then subsequently disabling GPS the last position retrieved from
the GPS was stored and continued to be broadcast.
This change introduces a check to see if we are transitioning from
GPS Enabled to GPS Disabled or Not Present. If we are, and fixed
position is not in use, then we clear the local position.
This will prevent inaccurate and undesired position broadcasts for those
who disable their GPS.
Fixes https://github.com/meshtastic/firmware/issues/7228
* Update triple click to also clear position
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add TraceRoute function to menus and modules to support node path tracing
* Adjust text spacing and line wrapping logic in trace route result result.
* Add HAS_SCREEN for TraceRouteModule drawFrame.
---------
Co-authored-by: Tom Fifield <tom@tomfifield.net>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Ben Meadors