inkstitch/README.md

31 KiB

ink/stitch: An Inkscape extension for designing machine embroidery patterns

Introduction

Want to design embroidery pattern files (PES, DST, etc) using free, open source software? Hate all the other options? Try this one.

I received a really wonderful christmas gift for a geeky programmer hacker: an embroidery machine. It's pretty much a CNC thread-bot... I just had to figure out how to design programs for it. The problem is, all free embroidery design software seemed to be terrible, especially when you add in the requirement of being able to run in Linux, my OS of choice.

So I wrote one.

Okay, not really. I'm pretty terrible at GUIs, but I found this nifty inkscape extension that was created and hacked on by a couple of other folks. It was pretty rudimentary, but it got the job done, and more importantly, it was super hackable. I hacked the hell out of it, and at this point ink/stitch is a viable entry-level machine embroidery design tool.

Quick Setup On Ubuntu 14.04 or later (and derivative Linux distributions)

Download the latest release, the inkscape-*.tar.gz file. Decompress this archive directly into ~/.config/inkscape/extensions, for example:

$ cd ~/.config/inkscape/extensions
$ tar zxf ~/Downloads/inkstitch-v1.0.0-Linux-x86_64.tar.gz

That's it! All python libraries and external dependencies are bundled (using the excellent pyinstaller), so you shouldn't need to set anything else up. Just restart Inkscape and the extension should be ready to go.

Continue reading in the "Usage" section.

Manual Setup

Inkscape

First, install Inkscape if you don't have it. I highly recommend version 0.92 or greater, which has a really key feature: the Objects panel. This gives you a heirarchical list of objects in your SVG file, listed in their stacking order. This is really important because the stacking order dictates the order that the shapes will be sewn in.

Versions 0.92.2 and higher let you bind a key to new commands, "stack up" and "stack down", which I assign to pageup and pagedown. These let you arbitrarily reorder objects in the SVG file, which lets you directly manipulate which order they stitch in. It works way better than the default "raise" and "lower" commands.

Python Dependencies

A few python modules are needed. In some cases this extension uses features that aren't available in the versions of the modules pre-packaged in distributions, so I recommend installing them directly with pip:

pip install -r requirements.txt

Extension installation

  1. Clone the extension source: git clone https://github.com/lexelby/inkstitch
  2. Install it as directed here

I prefer to symbolically link into my git clone, which allows me to hack on the code. Changes to the Python code take effect the next time the extension is run. Changes to the extension description files (*.inx) take effect the next time Inkscape is restarted

Optional: conversion program

The extension can output machine embroidery design files directly in Melco format. I don't even know what that is, so I don't use it. I prefer to use the CSV output format which can be consumed by another awesome open source project: Embroidermodder2. In theory, this project was going to be exactly what I wanted. In practice, it never got funded on Kickstarter and it's largely incomplete.

However, it contains a really awesome core library that knows pretty much every machine embroidery format and how to convert between them. I use it to convert the CSV files that ink/stitch outputs into the PES files that my SE400 uses.

Grab the source: git clone https://github.com/Embroidermodder/Embroidermodder. Build just libembroidery-convert using the instructions in "3)" in the Embroidermodder build docs. You can then use it like this: ./libembroidery-convert your-file.csv your-file.pes.

Since the CSV + libembroidery-convert method is the only method I use, it's the one I'll assume from here on. I'm not even sure if the other output formats from ink/stitch still work (or ever worked).

Usage

Basic Usage

First things first: I'm going to assume you know a few embroidery terms like "fill stitch" and "satin". Look those up if you're mentally 404ing, then come back here. I'm not going to assume you know some of the more advanced terms, because I had to learn all that when I started this project, so I might as well teach you too.

  1. Open up Inkscape and create a rectangle.
  2. Make sure it has both a stroke and a fill.
  3. Convert it to a path using Path -> Object to Path (because ink/stitch doesn't understand rectangles, circles, and the like, and ignores them).
  4. Run Extensions -> Embroidery -> Embroider. Use the default settings.

The rectangle you made will disappear and be replaced with some stripes and zig-zags. ink/stitch has hidden all of your layers and created a new one called Embroidery, in which it has palced a visual representation of the stitch plan it created. It has interpreted your shape as two instructions: Fill and Stroke. Fill is implemented using fill stitching, and Stroke is implemented by running satin stitching along the outline.

Select the horizontal lines using the "Edit Paths by Nodes" tool. Zoom in a bit and you'll see that the lines are actually made up of lots of points. Each point represents one stitch -- one needle penetration and interlocking of the top thread with the bobbin thread. Notice how the points all line up nicely in diagonals. This will give the fill stitching a nice, orderly visual appearance.

Now look at the zig-zags. These are the satin stitches. Note that the corners look pretty ugly. This is because satin stitches generated from a shape's stroke are pretty rudimentary and aren't implemented intelligently. You can exert much greater control over satin stitching using a Satin Column, described later.

The stitching preview you're looking at just now isn't intended to be permanent. I usually immediately undo it (ctrl-Z) after I've looked at the stitches. The actual work that ink/stitch does is to output a design file.

Stitching Out the Design

Where'd the design file go? One of the parameters you were able to specify in the filter settings dialog was the output directory. By default, the directory used is the place where you installed the extension's Python files. I output mine to ~/Documents/embroidery/output.

ink/stitch will create a file named something.csv, where something is the name of your svg file (e.g. something.svg). If something.csv already existed, it will be renamed to something.csv.1, and something.csv.1 will be renamed to something.csv.2, etc, up to 5 backup copies. When you've got the design the way you like it, save off a copy of something.csv.

Next, convert it to your machine's format using libembroidery-convert (as described above). Send it to your machine in whatever way one does that for your machine, and try stitching it out!

Ordering

Copy your rectangle and paste it elsewhere on your canvas. Deselect any shapes (Edit -> Deselect), re-run the extension, and look at the output. You'll see that both regions have been stitched, and there will be a line connecting them. That's a jump-stitch, where the machine will move a long distance between stitching the sections.

If you're like me, your machine can't automatically cut the thread between stitching sections, so you'll need to minimize jump stitches as much as possible through careful planning of your stitch path. If your machine can do thread cuts, congratulations! But you'll need to modify ink/stitch to allow you to specify a thread cut, because there's no way to do that right now.

However, note that ink/stitch pays attention to the colors you use for objects. If you change colors from one object to the next, ink/stitch will include a color-change instruction using the color you've set for the object. My machine cuts the thread and waits for me to switch to the new thread color.

Reordering

Use the Objects panel to view the stacking order of the objects in your SVG file. ink/stitch will stitch them in their stacking order, from lowest to highest. You can reorder them in the normal way in inkscape to affect the stitching order.

You can also use the Reorder extension. Hold shift and select the objects you'd like to reorder, one at a time, in the order you'd like them to end up in (lowest to highest). Run Embroidery -> Reorder. This extension will pull all of the selected objects out of wherever they were in the stacking order and insert them in order at the same place as the first object you selected. This can save you a ton of time. NOTE: this stopped working in more recent versions of inkscape, which no longer tell the extension what order you selected objects in.

Seeing the stitch plan for selected objects

If you have one or more objects selected when you run the Embroider extension, only those objects will be embroidered. This can be useful to help you fine-tune just one small section of your design.

Embroidery Parameters

When you run Embroider, you'll have the option to specify a few parameters like stitch length, fill stitch row spacing, etc. These are used as defaults for all objects in your design. You can override these parameters and set many more using the Embroidery -> Params extension.

This extension gives you an interface to control many aspects of the stitching of each object individually. To use it, first select one or more objects. Parameters will be applied to them all as a group. If the selected objects already have parameters set, these settings will be pre-loaded into the interface.

Parameters are stored in your SVG file as additional attributes on the XML objects. You can view these attributes using Inkscape's built-in XML editor panel, but you shouldn't actually need to do this during normal usage. Inkscape ignores attributes that it doesn't know, so these attributes will be saved right along with your SVG file. Note that other SVG programs may not retain these attributes, so be careful!

I recommend avoiding dependence on the default settings specified in the Embroider extension's settings window. In fact, I bypass it entirely by binding a keystroke (ctrl+e) to "Embroider (no preferences)" in Inkscape's settings. This way, I can quickly see the stitch plan just by pressing the keystroke. I also bind a keystroke to Params so that I can quickly view and change settings for each object.

Sidenote on extensions

Params is a bit weird, in that the dialog is produced by an entirely separate program (the extension) rather than Inkscape itself. This is due to the way Inkscape structures extensions. I wish ink/stitch could have deeper integration into Inkscape's user interface, but it's currently not possible. This is the price we pay for not having to write an entire vector graphics editor program :)

Another issue is that Inkscape has a memory leak related to extensions. The more times you run an extension, the more memory Inkscape uses and the slower it gets. I periodically save my SVG file, close Inkscape, and restart it to work around this issue. See above re: putting up with this kind of hassle so as not to have a to implement an entire vector graphics editor. Hopefully they'll fix this bug soon.

AutoFill

AutoFill is the default method for generating fill stitching. To use it, create a closed path in Inskcape and add a fill color. This algorithm works for complex shapes with or without holes.

ink/stitch will break the shape up into sections that it can embroider at once using back-and-forth rows of stitches. It then adds straight-stitching between sections until it's filled in the entire design. The staggered pattern of stitches is continued seamlessly between sections, so the end result doesn't appear to have any breaks. When moving from one section to the next, it generates running stitching along the border of the shape.

AutoFill parameters

Using the Params extension, you can set these parameters:

  • angle: The angle of the rows of stitches, in degrees. 0 is horizontal, and the angle increases in a counter-clockwise direction. Negative angles are allowed.
  • row spacing: distance between rows of stitches
  • maximum stitch length: the length of each stitch in a row. "Max" is because a shorter stitch may be used at the start or end of a row.
  • running stitch length: length of stitches around the outline of the fill region used when moving from section to section
  • staggers: stitches are staggered so that neighboring rows of stitches don't all fall in the same column (which would create a distracting valley effect). Setting this dictates how many rows apart the stitches will be before they fall in the same column position.

AutoFill Underlay

By default, AutoFill will cover the shape with one layer of stitches. In almost all cases, this won't look any good. The individual stitches will sink into the fabric (even if it's thin) and the fill will appear sparse. The fabric may even stick up between rows.

To solve this, you need underlay: an initial layer of stitches that hold up the final stitches. Underlay for fill stitch it's usually comprised of fill stitching 90 degrees offset from the final fill (called "top stitching"). The row spacing should be much wider than in the top stitching. The goal is to flatten out the fabric and give the top stitches "rails" to sit on.

In Params, you'll see an underlay tab next to the AutoFill tab. Enable it by checking the box. The default settings should be good enough for most cases: 90 degrees offset and row spacing 3x the spacing of the top stitching.

Manual Fill

Manual Fill is the old mode from before I figured out how to implement automatic fill routing. In some cases, AutoFill may not be an option, such as when the running stitches between sections are not acceptable for your design. Usually, fill region edges are covered over by satin, but not always.

In manual fill, the extension will still break up the shape into sections, each of which can be embroidered in one go. Then these sections will be fill-stitched one at a time, jumping directly between sections. You'll almost certainly want to break your shape up into smaller shapes and connect then using running stitches (described below). It's a painstaking process, made moreso because you'll need to do it twice: once for the underlay and again for the top stitching.

The flip option can help you with routing your stitch path. When you enable flip, stitching goes from right-to-left instead of left-to-right. Using flip and rotating 180 additional degrees (by adding or subtracting 180 from angle), you can cause fill stitching for a given shape to start from any of the four possible corners.

Running Stitch

Running stitch can be created by setting a dashed stroke on a path. Any kind of dashes will do the job, and the stroke width is irrelevant. ink/stitch will create stitches along the path using the stroke width you specify.

In order to avoid rounding corners, ash extra stitch will be added at the point of any sharp corners.

The repeats parameter says how many times time run down and back song the path. An odd number of repeats means that the stitches will end at the end of the path, while an even number means that stitching will return to the start of the path. The default is one repeat; that is, just traveling once from the start to the end of the path.

If an object consists of multiple paths, they will be stitched in order with a jump between each.

Simple Satin

A line without dashes will result in satin stitching. The width of the satin will be dictated by the stroke width. (For historical reasons, a stroke width less than 0.5 pixels will result in running stitch instead).

This is "simple satin": Embroider will plot zig-zags to the left and right of the line from start to end, but it won't do anything special around curves and corners. Sharper curves and corners will result in sparse stitching around the outside of the curve and dense stitching around the i. T

This won't look good and may even poke holes in the insides of corners. I avoid using plain satin entirely; it's just kept in for backward compatibility. It'll probably work fine for straight lines.

Satin Column

Satin Column mode gives you much greater control over how the satin is generated. You define a satin column using a shape made of two mostly-parallel lines. Embroider will draw zig-zags back and forth between the two lines. You can vary the thickness of the column as you like.

The two paths must have the same number of points. This means that each path will be made up of an equal number of Bezier curves. Each pair of points acts as a "checkpoint": Embroider will ensure that a "zag" ends up going from one point to the other.

Embroider considers each pair of Bezier curves, one at a time. It picks the longest if the two and determines how many zig-zags will be necessary to satisfy the zig-zag spacing setting. This makes it so that the outside of a curve will never have sparse stitching like with simple satin.

However, this does mean that the inside of a curve will have a higher stitch density than you specified. Be careful how you design sharp curves, because stitching at too high a density may poke a hole in the fabric!

To avoid this issue, transition your stitching to go around the corner at an angle, like this:

Some embroidery design programs solve this problem differently. They modify the satin such that some stitches on the inside corner don't go all the way to the edge, to avoid having the make penetrate the fabric too many times in the same spot. I haven't gotten around to implementing that yet. Pull requests welcome!

Satin Column supports these settings:

  • zig-zag spacing: the peak-to-peak distance between zig-zags.
  • pull compensation: Satin stitches pull the fabric together, resulting in a column narrower than you draw in Inkscape. This setting expands each pair of needle penetrations outward from the center of the satin column. You'll have to determine experimentally how much compensation you need for your combination of fabric, thread, and stabilizer.

Satin Column also supports three kinds of underlay, of which you can use any or all simultaneously. I use the terms defined in this excellent article on satin column design.

Center Walk Underlay

This is a row of running stitch down the center of the column and back. This may be all you need for thin satin columns. You can also use it as a base for more elaborate underlay.

Contour Underlay

This is a row of running stitch up one side of the column and back down the other. The rows are set in from the edge of the column by an amount you specify. For small or medium width satin, this may serve well enough by itself.

Zig-Zag Underlay

This is essentially a lower-density satin stitch sewn to the end of the column and back to the start. Added with contour underlay, you get the "German Underlay" mentioned in the article linked above. For wide columns or challenging fabrics, you can use all three underlay types together.

Workflow

Here's how I use ink/stitch to design embroidery patterns.

Pixels Per Millimeter

My embroidery machine (a Brother SE400) can handle patterns up to 10cm x 10cm (about 4in x 4in). Most machine embroidery design advice articles I've read talk in terms of millimeters, so that's what I work in.

My machine can (theoretically) position the needle with an accuracy of a tenth of a millimeter. The Brother PES format cannot encode a position any more precisely than this. In practice, even if a machine had finer accuracy than this, the realities of sewing on real fabric, even with the best stabilizer, mean that you can't get any more accurate than this (and you shouldn't bother trying).

Previously, I used a nonstandard resolution of 10 pixels per millimeter, and this was hardcoded into ink/stitch. Now, ink/stitch respects Inkscape's default of 96dpi.

Step 1: Sketch design or use an image

First, I get an idea for what I want my finished product to look like. If I'm basing my design off an existing picture or graphic, I load it into Inkscape in its own layer. Some graphics are amenable to Inkscape's auto-tracing feature, especially if I simplify the image in GIMP first.

After auto-tracing, I clean up the vector shapes, using "Simplify" and deleting nodes by hand when possible. My goal is to use as few Bezier curves as reasonably possible to represent the image.

If I need to trace an image by hand, I usually use the freehand drawing tool. This tool creates paths with a lot of Bezier nodes, so again, I'll simplify the curves as much as possible.

Working with an existing SVG image can save a ton of time, so consider using Google image search with the filter set to SVG.

For text, choose a font carefully. It's quite hard to make satin look good when it's 1mm wide or narrower. Sans-serif fonts tend to be the easiest. For text smaller than 4mm tall, you'll have a very difficult time making lowercase letters look good, so consider block-caps. Cursive/script fonts can work well, but it's not going to be as easy as you think. I find that I spend the most time on text by far.

Step 2: Plan stitch path and color changes

At this point, you'll have a vector graphic representation of your image. The next thing to do is to convert your vectors into the kind that Embroider understands and put them in the right order.

When you're designing for embroidery machines that can't cut the thread mid-sew or switch colors automatically, you're going to want to optimize your stitch path to reduce or hide jump stitches and make minimal color changes. I also try to avoid stitching over jump stitches when possible, because it's a total pain to trim them by hand when you do.

The order of stitching also affects how the fabric pulls and pushes. Each stitch will distort the fabric, and you'll need to take this into account and compensate accordingly. Look for articles on machine embroidery distortion for more info on this.

Step 3: create the embroidery vectors

I make heavy use of layers and groups at this point. If I've traced an image, I'll leave it as the lowest layer and set it invisible in the Layers or Objects palette. Any layer, group, or vector shape that is set invisible will be ignored by Embroider.

I keep my initial traced vectors in their own layer and use them as a reference when designing embroidery vectors. I copy and paste then as necessary into a higher layer and work with the copies.

I use only AutoFill and Satin Columns in my designs. I begin converting filled areas to AutoFill regions. Each time I create an AutoFill shape, I set its parameters using Params. Then I select it and run Embroider, which will cause it to show a stitch plan for just the selected object(s).

I examine the resulting stitch plan using the node editor tool. Each vertex is a single stitch; the needle will penetrate the fabric and interlock with the bobbin thread at this point. Once I'm done examining the stitch plan, I Undo the Embroider operation to remove the stitch plan and make my vectors visible again. Then I make any changes necessary, re-run Embroider, and repeat until it looks right.

At this point, I save my SVG file. If Inkscape is starting to become sluggish (due to the memory leak described above), I'll restart it before continuing.

Next, I work on Satins. Remember that a Satin Column is defined by two lines that run along the edges of the column. It's usually a good idea to run satin along the outside border of a fill region. Inkscape makes this easy. I copy and paste the shape from the traced vectors, then disable Fill and enable Stroke. I set the stroke width to my desired satin width. Finally, I use the "Stroke to Path" option to convert just the stroke into its own path.

At this point, it's necessary to cut the paths so that they aren't a continuous loop. The cut will also tell Embroider where to start stitching from. Add a point at the desired cut location by double-clicking on the path with the Node Editor tool active. Cut at this point by selecting at and pressing shift+b. Repeat for the second path.

Now you've got an object made of two paths. They need to be going on the same direction for Satin Column to work. You can tell what direction the path goes in by enabling direction indicators in Inkscape's preferences. To reverse one of the paths, select one of its points and choose "Reverse Path". I bind this to ctrl+r in Inkscape's preferences.

By now, it's likely that the two paths in the object have an unequal number of nodes. As described above, a Satin Column is made of consecutive pairs of points on the two paths. You have a couple of techniques available to make your nodes line up in pairs:

  • simplify the shape (control+L)
  • delete extra nodes
  • add more nodes
  • joining nodes

I usually Simplify first if necessary to reduce the path to a manageable number of nodes. Remember that machine embroidery is fairly imprecise and your final product will not have the incredibly fine details that you see on your screen, so simplifying can often be acceptable even if it changes the path.

Next, I try to delete nodes or join. Inkscape will attempt to manipulate the neighboring nodes as necessary to keep the path the same, but I find that it's not particularly good at this. Instead of deleting a troublesome point, it can often work better to simply add a matching point on the other path.

Finally, I run Embroider with the path selected and examine the output. I add, remove, and adjust points as necessary to make my satin look nice.

You may find that you get the dreaded error, "object has two paths with an unequal number of points". This can be confusing because it may look like your paths have the same number of points. Usually this is because of duplicate points: multiple points with the exact same coordinates or very similar coordinates. To find them, I drag-select each point in turn, examining the bottom status bar. It will tell me how many points I've selected. If it looks like I've selected just one but Inkscape says I've selected 3, then it's likely that I've found my culprit.

Often just pressing shift+J (join nodes) will eliminate the extra points without modifying the shape. Sometimes it won't, and in cases like that, I've had luck with adding extra points on either side of the "cluster", then delete the "cluster". The extra points anchor the shape and disallow Inkscape from messing it up. Then it may be possible to delete the added points, or I just add points to the other path to match with them.

Step 4: Ordering

Once I've created all of my vectors and test-embroidered them individually, it's time to put everything in the right order. This is where the Objects tool from the latest development version of Inkscape (described above) comes in useful. Because my embroidery machine can neither trim threads nor switch colors mid-sew, I optimize my order to minimize color changes and reduce or hide jump-stitches.

Embroider will stitch objects in exactly the order they appear in your SVG document, from lowest to highest in stacking order. If the distance between two objects is long, Embroider will add a jump-stitch between them automatically. It uses the color of the object to determine thread color, so changes in color from one object to the next will result in a thread-change instruction being added to the embroidery output file.

Inkscape gives you the ability to raise and lower objects in the stacking order using the PageUp and PageDown keys. However, it seems to be unwilling to give the user complete control over the stacking order. I think this has to do with whether objects overlap: if A and B don't overlap, Inkscape doesn't care how they're stacked in the SVG file and it sometimes won't let you reorder them.

To solve this, I created the Reorder extension. To use it, hold down the shift key and select objects one at a time in the order you'd like them to appear in the SVG file and run Reorder. Reorder will remove the selected objects from the SVG XML tree and then re-add them at the location of the first-selected object, in the order you selected them.

You can also manually manipulate the underlying SVG XML structure by using Inkscape's XML Editor pane. Its "Raise" and "Lower" buttons directly manipulate the order of XML tags in the SVG file and are not subject to the same limitations as PageUp and PageDown. Note that the ordering of XML tags in the XML Editor tool is the reverse of the order of objects in the Objects tool.

Step 4: Render to CSV

Once I've got everything in the right order, I deselect all objects and run Embroider again. This will embroider all visible objects in the document. As described in the Setup section above, I render my embroidery file in CSV format and convert it with EmbroiderModder's libembroidery-convert utility.

Embroider will create a file in the specified output directory named after your SVG file, but with the extension changed to .csv. It will back up any existing file there, storing up to 5 old copies of each file.

Step 5: Convert to PES and upload

My sewing machine uses the PES format, so I convert the CSV file into a .PES and send it over to my sewing machine. My Brother SE400 acts like a (very small!) USB flash drive. I use a script to do the CSV and upload steps all at once.

Step 6: Test-sew

I've never gotten an embroidery file correct on the first try. There's always room for improvement! To test out my design, I prepare a test piece of fabric that matches my final fabric as closely as possible. I use the same stabilizer and the exact same fabric if possible. For t-shirts, I try to find a similar fabric (usually knit). Knits need a lot of stabilization.

I sew out the design, watching the machine to make sure that there aren't any surprises. I'm watching for gaps that indicate that the fabric has been distorted. I'm also watching for areas where stitches are piling up too closely and the machine is having trouble sewing, which indicates that the stitch density is too high. Finally, of course, I'm watching in giddy anticipation to see my design for the first time! :)

Step 7+: iterate

Then I go back and tweak my design. Hopefully it only takes a few tries to get it how I want it. Once I'm done, I copy the CSV file from my output directory, just to avoid accidentally overwriting it in the future.