kopia lustrzana https://github.com/sh123/esp32_loraprs
133 wiersze
6.3 KiB
C
133 wiersze
6.3 KiB
C
#ifndef CONFIG_H
|
|
#define CONFIG_H
|
|
|
|
// Uncomment for SX126X module usage
|
|
// #define USE_SX126X
|
|
|
|
// Check your module name at https://github.com/jgromes/RadioLib/wiki/Modules
|
|
#ifdef USE_SX126X
|
|
#define MODULE_NAME SX1268
|
|
#else
|
|
#define MODULE_NAME SX1278
|
|
#endif
|
|
|
|
// generic options
|
|
#define LED_TOGGLE_PERIOD 1000 // heartbeat LED period
|
|
#define SERIAL_BAUD_RATE 115200 // USB serial baud rate
|
|
|
|
// USB serial logging
|
|
// set to DebugLogLevel::LVL_TRACE for packet logging
|
|
// set to DebugLogLevel::LVL_NONE to disable logging
|
|
#define CFG_LOG_LEVEL DebugLogLevel::LVL_INFO
|
|
|
|
// select between client mode and APRS-IS gate mode
|
|
#ifndef CFG_IS_CLIENT_MODE
|
|
#define CFG_IS_CLIENT_MODE true // false - server mode (APRS-IS gate mode)
|
|
#endif
|
|
|
|
// change pinouts if not defined through native board LORA_* definitions
|
|
#ifndef LORA_RST
|
|
#pragma message("LoRa pin definitions are not found, redefining...")
|
|
#define LORA_RST 26
|
|
#define LORA_IRQ 12
|
|
#endif
|
|
|
|
// LoRa pinouts
|
|
#define CFG_LORA_PIN_SS SS
|
|
#define CFG_LORA_PIN_RST LORA_RST
|
|
#define CFG_LORA_PIN_A LORA_IRQ // (sx127x - dio0, sx126x/sx128x - dio1)
|
|
#ifdef USE_SX126X
|
|
#define CFG_LORA_PIN_B 14 // (sx127x - dio1, sx126x/sx128x - busy)
|
|
#define CFG_LORA_PIN_RXEN 32 // (sx127x - unused, sx126x - RXEN pin number)
|
|
#define CFG_LORA_PIN_TXEN 33 // (sx127x - unused, sx126x - TXEN pin number)
|
|
#else
|
|
#define CFG_LORA_PIN_B RADIOLIB_NC
|
|
#define CFG_LORA_PIN_RXEN RADIOLIB_NC
|
|
#define CFG_LORA_PIN_TXEN RADIOLIB_NC
|
|
#endif
|
|
|
|
// Redefine LED if not defined in Arduino to have module heartbeat indication
|
|
#ifndef BUILTIN_LED
|
|
#pragma message("BUILDIN_LED is not found, defining as 2")
|
|
#define BUILTIN_LED 2
|
|
#endif
|
|
|
|
// CAD and ISR usage selection
|
|
#ifdef USE_SX126X
|
|
#define CFG_LORA_USE_CAD true // do not transmit if channel is busy
|
|
#else
|
|
#define CFG_LORA_USE_CAD true // set to true to utilize carrier detection
|
|
#endif
|
|
|
|
// modulation
|
|
#define CFG_MOD_TYPE_LORA 0
|
|
#define CFG_MOD_TYPE_FSK 1
|
|
#define CFG_MOD_TYPE CFG_MOD_TYPE_LORA
|
|
|
|
// general radio parameters
|
|
#define CFG_LORA_FREQ_RX 433.775e6 // RX frequency in MHz
|
|
#define CFG_LORA_FREQ_TX 433.775e6 // TX frequency in MHz
|
|
#define CFG_LORA_PWR 20 // output power in dBm
|
|
|
|
// LoRa protocol default parameters (they need to match between devices!!!)
|
|
#define CFG_LORA_BW 125e3 // bandwidth (from 7.8 kHz up to 500 kHz)
|
|
#define CFG_LORA_SF 12 // spreading factor (6 - 12), 6 requires implicit header mode
|
|
#define CFG_LORA_CR 7 // coding rate (5 - 8)
|
|
#define CFG_LORA_CRC 1 // 0 - disabled, 1 - 1 byte, 2 - 2 bytes
|
|
#define CFG_LORA_EXPLICIT true // header mode, true - explicit, false - implicit
|
|
#define CFG_LORA_SYNC 0x12 // sync word (0x12 - private used by other trackers, 0x34 - public used by LoRaWAN)
|
|
#define CFG_LORA_PREAMBLE 8 // preamble length from 6 to 65535
|
|
|
|
// fsk modem default parameters (they need to match between devices!!!)
|
|
#define CFG_FSK_BIT_RATE 4.8 // bit rate in Kbps from 0.6 to 300.0
|
|
#define CFG_FSK_FREQ_DEV 1.2 // frequency deviation in kHz from 0.6 to 200.0
|
|
#define CFG_FSK_RX_BW 9.7 // rx bandwidth in kHz !!discrete!! from 4.8 to 467.0
|
|
|
|
// WiFi client and AP options
|
|
#define CFG_WIFI_ENABLE_AP false // run as wifi access point (for CFG_KISS_TCP_IP mode)
|
|
#define CFG_WIFI_SSID "<ssid>" // connect to SSID or run as this SSID in AP mode
|
|
#define CFG_WIFI_KEY "<key>" // wifi key
|
|
|
|
// Bluetooth
|
|
#define CFG_BT_NAME "loraprs" // set to empty to disable Bluetooth
|
|
#define CFG_BT_USE_BLE false // set to true to use bluetooth low energy (for ios devices)
|
|
|
|
// USB serial
|
|
#define CFG_USB_SERIAL_ENABLE false // true - enable KISS communication over USB Serial (e.g. with APRSDroid over USB-OTG), disables USB logging
|
|
|
|
// KISS protocol options
|
|
#define CFG_KISS_EXTENSIONS false // true - enable modem control from application with KISS commands and signal reports
|
|
#define CFG_KISS_TCP_IP false // true - run as KISS TCP/IP server, no bluetooth operations performed
|
|
|
|
// APRS-IS options, valid in when CFG_IS_CLIENT_MODE = false
|
|
#define CFG_APRS_LOGIN "NOCALL-10"
|
|
#define CFG_APRS_PASS "12345"
|
|
#define CFG_APRS_FILTER "r/35.60/139.80/25" // multiple are space separated, see http://www.aprs-is.net/javAPRSFilter.aspx
|
|
#define CFG_APRS_RAW_BKN "NOCALL-10>APZMDM,WIDE1-1:!0000.00N/00000.00E#LoRA 433.775MHz/BW125/SF12/CR7/0x12"
|
|
|
|
// APRS-IS gateway options, valid when CFG_IS_CLIENT_MODE = false
|
|
#define CFG_SIGNAL_REPORT true // include signal report into the comment when sending to APRS-IS
|
|
#define CFG_PERSISTENT_APRS true // keep tcp/ip connection open (lot of traffic), otherwise connect on new packet (very rare traffic)
|
|
#define CFG_DIGIREPEAT false // digirepeat incoming packets
|
|
#define CFG_RF_TO_IS true // forward packets from radio to internet
|
|
#define CFG_IS_TO_RF false // forward packets from internet to radio based on CFG_APRS_FILTER
|
|
#define CFG_BEACON false // enable perdiodic beacon from CFG_APRS_RAW_BKN
|
|
#define CFG_TEXT_PACKETS false // enable aprs TNC2 text packets instead of binary for interoperability with other projects (disables KISS + AX.25!)
|
|
#define CFG_TEXT_PACKETS_3 false // true - enable aprs-lora 3 byte prefix '<', 0xff, 0x01
|
|
|
|
// Frequency correction for narrow band bandwidths
|
|
#define CFG_FREQ_CORR false // true - correct own frequency based on received packet
|
|
#define CFG_FREQ_CORR_DELTA 1000 // correct when frequency difference is larger than this value
|
|
|
|
// PTT control
|
|
#define CFG_PTT_ENABLE false // enable external ptt (relay) control (for amplifier)
|
|
#define CFG_PTT_PIN 12 // PTT pin
|
|
#define CFG_PTT_TX_DELAY_MS 50 // delay between relay switching ON and transmission startup
|
|
#define CFG_PTT_TX_TAIL_MS 10 // delay between stopping transmission and relay switching OFF
|
|
|
|
// Enable modem telemetry
|
|
#define CFG_TLM_ENABLE false // enable modem battery monitor
|
|
#define CFG_TLM_BAT_MON_PIN 36 // battery ADC pin
|
|
#define CFG_TLM_BAT_MON_CAL 0.37f // calibration coefficient
|
|
|
|
#endif // CONFIG_H
|