#ifndef CONFIG_H #define CONFIG_H // Uncomment for SX126X module usage // #define USE_SX126X // Check your module name at https://github.com/jgromes/RadioLib/wiki/Modules #ifdef USE_SX126X #define MODULE_NAME SX1268 #else #define MODULE_NAME SX1278 #endif // generic options #define LED_TOGGLE_PERIOD 1000 // heartbeat LED period #define SERIAL_BAUD_RATE 115200 // USB serial baud rate // USB serial logging // set to DebugLogLevel::LVL_TRACE for packet logging // set to DebugLogLevel::LVL_NONE to disable logging #define CFG_LOG_LEVEL DebugLogLevel::LVL_INFO // select between client mode and APRS-IS gate mode #ifndef CFG_IS_CLIENT_MODE #define CFG_IS_CLIENT_MODE true // false - server mode (APRS-IS gate mode) #endif // change pinouts if not defined through native board LORA_* definitions #ifndef LORA_RST #pragma message("LoRa pin definitions are not found, redefining...") #define LORA_RST 26 #define LORA_IRQ 12 #endif // LoRa pinouts #define CFG_LORA_PIN_SS SS #define CFG_LORA_PIN_RST LORA_RST #define CFG_LORA_PIN_A LORA_IRQ // (sx127x - dio0, sx126x/sx128x - dio1) #ifdef USE_SX126X #define CFG_LORA_PIN_B 14 // (sx127x - dio1, sx126x/sx128x - busy) #define CFG_LORA_PIN_RXEN 32 // (sx127x - unused, sx126x - RXEN pin number) #define CFG_LORA_PIN_TXEN 33 // (sx127x - unused, sx126x - TXEN pin number) #else #define CFG_LORA_PIN_B RADIOLIB_NC #define CFG_LORA_PIN_RXEN RADIOLIB_NC #define CFG_LORA_PIN_TXEN RADIOLIB_NC #endif // Redefine LED if not defined in Arduino to have module heartbeat indication #ifndef BUILTIN_LED #pragma message("BUILDIN_LED is not found, defining as 2") #define BUILTIN_LED 2 #endif // CAD and ISR usage selection #ifdef USE_SX126X #define CFG_LORA_USE_CAD true // do not transmit if channel is busy #else #define CFG_LORA_USE_CAD true // set to true to utilize carrier detection #endif // modulation #define CFG_MOD_TYPE_LORA 0 #define CFG_MOD_TYPE_FSK 1 #define CFG_MOD_TYPE CFG_MOD_TYPE_LORA // general radio parameters #define CFG_LORA_FREQ_RX 433.775e6 // RX frequency in MHz #define CFG_LORA_FREQ_TX 433.775e6 // TX frequency in MHz #define CFG_LORA_PWR 20 // output power in dBm // LoRa protocol default parameters (they need to match between devices!!!) #define CFG_LORA_BW 125e3 // bandwidth (from 7.8 kHz up to 500 kHz) #define CFG_LORA_SF 12 // spreading factor (6 - 12), 6 requires implicit header mode #define CFG_LORA_CR 7 // coding rate (5 - 8) #define CFG_LORA_CRC 1 // 0 - disabled, 1 - 1 byte, 2 - 2 bytes #define CFG_LORA_EXPLICIT true // header mode, true - explicit, false - implicit #define CFG_LORA_SYNC 0x12 // sync word (0x12 - private used by other trackers, 0x34 - public used by LoRaWAN) #define CFG_LORA_PREAMBLE 8 // preamble length from 6 to 65535 // fsk modem default parameters (they need to match between devices!!!) #define CFG_FSK_BIT_RATE 4.8 // bit rate in Kbps from 0.6 to 300.0 #define CFG_FSK_FREQ_DEV 1.2 // frequency deviation in kHz from 0.6 to 200.0 #define CFG_FSK_RX_BW 9.7 // rx bandwidth in kHz !!discrete!! from 4.8 to 467.0 // WiFi client and AP options #define CFG_WIFI_ENABLE_AP false // run as wifi access point (for CFG_KISS_TCP_IP mode) #define CFG_WIFI_SSID "" // connect to SSID or run as this SSID in AP mode #define CFG_WIFI_KEY "" // wifi key // Bluetooth #define CFG_BT_NAME "loraprs" // set to empty to disable Bluetooth #define CFG_BT_USE_BLE false // set to true to use bluetooth low energy (for ios devices) // USB serial #define CFG_USB_SERIAL_ENABLE false // true - enable KISS communication over USB Serial (e.g. with APRSDroid over USB-OTG), disables USB logging // KISS protocol options #define CFG_KISS_EXTENSIONS false // true - enable modem control from application with KISS commands and signal reports #define CFG_KISS_TCP_IP false // true - run as KISS TCP/IP server, no bluetooth operations performed // APRS-IS options, valid in when CFG_IS_CLIENT_MODE = false #define CFG_APRS_LOGIN "NOCALL-10" #define CFG_APRS_PASS "12345" #define CFG_APRS_FILTER "r/35.60/139.80/25" // multiple are space separated, see http://www.aprs-is.net/javAPRSFilter.aspx #define CFG_APRS_RAW_BKN "NOCALL-10>APZMDM,WIDE1-1:!0000.00N/00000.00E#LoRA 433.775MHz/BW125/SF12/CR7/0x12" // APRS-IS gateway options, valid when CFG_IS_CLIENT_MODE = false #define CFG_SIGNAL_REPORT true // include signal report into the comment when sending to APRS-IS #define CFG_PERSISTENT_APRS true // keep tcp/ip connection open (lot of traffic), otherwise connect on new packet (very rare traffic) #define CFG_DIGIREPEAT false // digirepeat incoming packets #define CFG_RF_TO_IS true // forward packets from radio to internet #define CFG_IS_TO_RF false // forward packets from internet to radio based on CFG_APRS_FILTER #define CFG_BEACON false // enable perdiodic beacon from CFG_APRS_RAW_BKN #define CFG_TEXT_PACKETS false // enable aprs TNC2 text packets instead of binary for interoperability with other projects (disables KISS + AX.25!) #define CFG_TEXT_PACKETS_3 false // true - enable aprs-lora 3 byte prefix '<', 0xff, 0x01 // Frequency correction for narrow band bandwidths #define CFG_FREQ_CORR false // true - correct own frequency based on received packet #define CFG_FREQ_CORR_DELTA 1000 // correct when frequency difference is larger than this value // PTT control #define CFG_PTT_ENABLE false // enable external ptt (relay) control (for amplifier) #define CFG_PTT_PIN 12 // PTT pin #define CFG_PTT_TX_DELAY_MS 50 // delay between relay switching ON and transmission startup #define CFG_PTT_TX_TAIL_MS 10 // delay between stopping transmission and relay switching OFF // Enable modem telemetry #define CFG_TLM_ENABLE false // enable modem battery monitor #define CFG_TLM_BAT_MON_PIN 36 // battery ADC pin #define CFG_TLM_BAT_MON_CAL 0.37f // calibration coefficient #endif // CONFIG_H