Add files via upload

Config for Oled SH1106 with Stratux with BME280
2021-01-10 22:32:46 +01:00 · 2021-01-10 22:32:46 +01:00 · 57cb211177
commit 57cb211177
--- a/87
+++ b/87
@ -0,0 +1,87 @@
+#define DEFAULT_AcftType        8          // [0..15] default aircraft-type: Powered Aircraft
+#define DEFAULT_GeoidSepar     40          // [m]
+#define DEFAULT_CONbaud    115200
+#define DEFAULT_PPSdelay      100
+#define DEFAULT_FreqPlan        0
+#define DEFAULT_DispPage        3          // Fab501 Page to Display After Boot or Reset	
+
+
+// #define WITH_HELTEC                        // HELTEC module: PCB LED on GPI025
+// #define WITH_HELTEC_V2                     // HELTEC module v2
+// #define WITH_TTGO                          // TTGO module: PCB LED on GPIO2, GPIO25 free to use as DAC2 output
+// #define WITH_TBEAM                          // T-Beam module
+#define WITH_TBEAM_V10                      // T-Beam module
+// #define WITH_M5_JACEK                         // JACEK M5 ESP32 OGN-Tracker
+// #define WITH_FollowMe                         // by Avionix
+
+// #define WITH_ILI9341                        // 320x240 M5stack
+// #define WITH_ST7789                         // IPS 240x240 ST7789
+// #define WITH_TFT_LCD                       // TFT LCD
+// #define WITH_OLED                          // OLED display on the I2C: some TTGO modules are without OLED display
+// #define WITH_OLED2                         // 2nd OLED display, I2C address next higher
+#define WITH_U8G2_OLED                     // I2C OLED through the U8g2 library
+#define WITH_U8G2_SH1106                   // correct controller for the bigger OLED
+// #define WITH_U8G2_FLIP                     // flip the OLED screen (rotate by 180deg)
+
+#define WITH_RFM95                         // RF chip selection:  both HELTEC and TTGO use sx1276 which is same as RFM95
+
+// #define WITH_SLEEP                         // with software sleep mode controlled by the long-press on the button
+
+#define WITH_AXP                           // with AXP192 power controller (T-BEAM V1.0)
+// #define WITH_BQ                            // with BQ24295  power controller (FollowMe)
+
+// #define WITH_LED_RX
+// #define WITH_LED_TX
+
+// #define WITH_GPS_ENABLE                    // use GPS_ENABLE control line to turn the GPS ON/OFF
+#define WITH_GPS_PPS                       // use the PPS signal from GPS for precise time-sync.
+#define WITH_GPS_CONFIG                    // attempt to configure higher GPS baud rate and airborne mode
+
+#define WITH_GPS_UBX                       // GPS understands UBX
+// #define WITH_GPS_MTK                       // GPS understands MTK
+// #define WITH_GPS_SRF
+// #define WITH_MAVLINK
+
+#define WITH_GPS_UBX_PASS                  // to pass directly UBX packets to/from GPS
+#define WITH_GPS_NMEA_PASS                  // to pass directly NMEA to/from GPS
+
+// #define WITH_BMP180                        // BMP180 pressure sensor
+// #define WITH_BMP280                        // BMP280 pressure sensor
+#define WITH_BME280                        // BMP280 with humidity (but still works with BMP280)
+// #define WITH_MS5607                        // MS5607 pressure sensor
+// #define WITH_MS5611                        // MS5611 pressure sensor
+
+// #define WITH_BMX055                        // BMX055 magnetic and IMU sensor
+
+// #define WITH_LORAWAN                       // LoRaWAN connectivity
+// #define WITH_FANET                         // FANET transmission and reception
+#define WITH_PAW			   // Add PAW transmission
+
+#define WITH_PFLAA                         // PFLAU and PFLAA for compatibility with XCsoar and LK8000
+// #define WITH_POGNT
+// #define WITH_GDL90
+// #define WITH_PGAV5
+#define WITH_LOOKOUT
+
+#define WITH_CONFIG                        // interpret the console input: $POGNS to change parameters
+
+#define WITH_BEEPER                        // with digital buzzer
+// #define WITH_SOUND                         // with analog sound produced by DAC on pin 25
+
+// #define WITH_KNOB
+// #define WITH_VARIO
+
+// #define WITH_SD                            // use the SD card in SPI mode and FAT file system
+#define WITH_SPIFFS                        // use SPIFFS file system in Flash
+// #define WITH_SPIFFS_FAT
+#define WITH_LOG                           // log own positions and other received to SPIFFS
+// #define WITH_SDLOG                         // log own position and other data to uSD card
+
+#define WITH_STRATUX
+#define WITH_BT_SPP                        // Bluetooth serial port for smartphone/tablet link
+#define WITH_WIFI                          // attempt to connect to the wifi router for uploading the log files
+// #define WITH_AP                            // Open Access Point MOde
+#define WITH_HTTP                           // Open Web Interface
+
+// #define WITH_ENCRYPT                       // Encrypt (optionally) the position
+