mirror
/
esp32-ogn-tracker
kopia lustrzana https://github.com/pjalocha/esp32-ogn-tracker
1
0
Forkuj 0
Kod Zgłoszenia Projekty Wydania Wiki Aktywność

Add files via upload 

Add the Selection of the First DispPage after Boot
pull/30/head
Fab501 2021-01-10 22:31:41 +01:00 zatwierdzone przez GitHub
rodzic 63be645934
commit c3751634a5
Nie znaleziono w bazie danych klucza dla tego podpisu
ID klucza GPG: 4AEE18F83AFDEB23
2 zmienionych plików z 24 dodań i 20 usunięć
Pokaż statystyki Ściągnij plik aktualizacji Ściągnij plik porównania Expand all files Collapse all files

40
main/config.h
Wyświetl plik

@ -1,17 +1,18 @@
#define DEFAULT_AcftType 1 // [0..15] default aircraft-type: glider
#define DEFAULT_AcftType 8 // [0..15] default aircraft-type: Powered Aircraft
#define DEFAULT_GeoidSepar 40 // [m]
#define DEFAULT_CONbaud 115200
#define DEFAULT_PPSdelay 100
#define DEFAULT_FreqPlan 0
#define DEFAULT_DispPage 3 // Fab501 Page to Display After Boot or Reset
// #define WITH_HELTEC // HELTEC module: PCB LED on GPI025
// #define WITH_HELTEC_V2 // HELTEC module v2
// #define WITH_TTGO // TTGO module: PCB LED on GPIO2, GPIO25 free to use as DAC2 output
// #define WITH_TBEAM // T-Beam module
// #define WITH_TBEAM_V10 // T-Beam module
#define WITH_TBEAM_V10 // T-Beam module
// #define WITH_M5_JACEK // JACEK M5 ESP32 OGN-Tracker
#define WITH_FollowMe // by Avionix
// #define WITH_FollowMe // by Avionix
// #define WITH_ILI9341 // 320x240 M5stack
// #define WITH_ST7789 // IPS 240x240 ST7789
@ -20,29 +21,29 @@
// #define WITH_OLED2 // 2nd OLED display, I2C address next higher
#define WITH_U8G2_OLED // I2C OLED through the U8g2 library
#define WITH_U8G2_SH1106 // correct controller for the bigger OLED
#define WITH_U8G2_FLIP // flip the OLED screen (rotate by 180deg)
// #define WITH_U8G2_FLIP // flip the OLED screen (rotate by 180deg)
#define WITH_RFM95 // RF chip selection: both HELTEC and TTGO use sx1276 which is same as RFM95
// #define WITH_SLEEP // with software sleep mode controlled by the long-press on the button
// #define WITH_AXP // with AXP192 power controller (T-BEAM V1.0)
#define WITH_AXP // with AXP192 power controller (T-BEAM V1.0)
// #define WITH_BQ // with BQ24295 power controller (FollowMe)
// #define WITH_LED_RX
// #define WITH_LED_TX
#define WITH_GPS_ENABLE // use GPS_ENABLE control line to turn the GPS ON/OFF
// #define WITH_GPS_ENABLE // use GPS_ENABLE control line to turn the GPS ON/OFF
#define WITH_GPS_PPS // use the PPS signal from GPS for precise time-sync.
#define WITH_GPS_CONFIG // attempt to configure higher GPS baud rate and airborne mode
// #define WITH_GPS_UBX // GPS understands UBX
#define WITH_GPS_MTK // GPS understands MTK
#define WITH_GPS_UBX // GPS understands UBX
// #define WITH_GPS_MTK // GPS understands MTK
// #define WITH_GPS_SRF
// #define WITH_MAVLINK
// #define WITH_GPS_UBX_PASS // to pass directly UBX packets to/from GPS
// #define WITH_GPS_NMEA_PASS // to pass directly NMEA to/from GPS
#define WITH_GPS_UBX_PASS // to pass directly UBX packets to/from GPS
#define WITH_GPS_NMEA_PASS // to pass directly NMEA to/from GPS
// #define WITH_BMP180 // BMP180 pressure sensor
// #define WITH_BMP280 // BMP280 pressure sensor
@ -52,8 +53,9 @@
// #define WITH_BMX055 // BMX055 magnetic and IMU sensor
#define WITH_LORAWAN // LoRaWAN connectivity
#define WITH_FANET // FANET transmission and reception
// #define WITH_LORAWAN // LoRaWAN connectivity
// #define WITH_FANET // FANET transmission and reception
#define WITH_PAW // Add PAW transmission
#define WITH_PFLAA // PFLAU and PFLAA for compatibility with XCsoar and LK8000
// #define WITH_POGNT
@ -63,21 +65,23 @@
#define WITH_CONFIG // interpret the console input: $POGNS to change parameters
// #define WITH_BEEPER // with digital buzzer
#define WITH_BEEPER // with digital buzzer
// #define WITH_SOUND // with analog sound produced by DAC on pin 25
// #define WITH_KNOB
// #define WITH_VARIO
#define WITH_SD // use the SD card in SPI mode and FAT file system
// #define WITH_SD // use the SD card in SPI mode and FAT file system
#define WITH_SPIFFS // use SPIFFS file system in Flash
#define WITH_SPIFFS_FAT
// #define WITH_SPIFFS_FAT
#define WITH_LOG // log own positions and other received to SPIFFS
#define WITH_SDLOG // log own position and other data to uSD card
// #define WITH_SDLOG // log own position and other data to uSD card
// #define WITH_STRATUX
#define WITH_STRATUX
#define WITH_BT_SPP // Bluetooth serial port for smartphone/tablet link
// #define WITH_WIFI // attempt to connect to the wifi router for uploading the log files
#define WITH_WIFI // attempt to connect to the wifi router for uploading the log files
// #define WITH_AP // Open Access Point MOde
#define WITH_HTTP // Open Web Interface
// #define WITH_ENCRYPT // Encrypt (optionally) the position

4
main/disp.cpp
Wyświetl plik

@ -26,11 +26,11 @@
#ifdef WITH_U8G2_OLED
const uint8_t DISP_Pages = 12;
static uint8_t DISP_Page = 0;
static uint8_t DISP_Page = DEFAULT_DispPage ; //Fab501 before 0
#endif
#if defined(WITH_ST7789) || defined(WITH_ILI9341)
const uint8_t DISP_Pages = 9;
static uint8_t DISP_Page = 0;
static uint8_t DISP_Page = DEFAULT_DispPage ; //Fab501 before 0
#endif