esp-idf/examples/openthread/ot_cli/README.md

133 wiersze
3.1 KiB
Markdown

| Supported Targets | ESP32-C6 | ESP32-H2 |
| ----------------- | -------- | -------- |
# OpenThread Command Line Example
This example demonstrates an [OpenThread CLI](https://github.com/openthread/openthread/blob/master/src/cli/README.md), with some additional features such as TCP, UDP and Iperf.
## How to use example
### Hardware Required
To run this example, a board with IEEE 802.15.4 module (for example ESP32-H2) is required.
### Configure the project
```
idf.py menuconfig
```
The example can run with the default configuration. OpenThread Command Line is enabled with UART as the default interface. Additionally, USB JTAG is also supported and can be activated through the menuconfig:
```
Component config → ESP System Settings → Channel for console output → USB Serial/JTAG Controller
```
### Build, Flash, and Run
Build the project and flash it to the board, then run monitor tool to view serial output:
```
idf.py -p PORT build flash monitor
```
Now you'll get an OpenThread command line shell.
### Example Output
The `help` command will print all of the supported commands.
```bash
> help
I(7058) OPENTHREAD:[INFO]-CLI-----: execute command: help
bbr
bufferinfo
ccathreshold
channel
child
childip
childmax
childsupervision
childtimeout
coap
contextreusedelay
counters
dataset
delaytimermin
diag
discover
dns
domainname
eidcache
eui64
extaddr
extpanid
factoryreset
...
```
## Set Up Network
To run this example, at least two ESP32-H2 boards flashed with this ot_cli example are required.
On the first device, run the following commands:
```bash
> factoryreset
... # the device will reboot
> dataset init new
Done
> dataset commit active
Done
> ifconfig up
Done
> thread start
Done
# After some seconds
> state
leader
Done
```
Now the first device has formed a Thread network as a leader. Get some information which will be used in next steps:
```bash
> ipaddr
fdde:ad00:beef:0:0:ff:fe00:fc00
fdde:ad00:beef:0:0:ff:fe00:8000
fdde:ad00:beef:0:a7c6:6311:9c8c:271b
fe80:0:0:0:5c27:a723:7115:c8f8
# Get the Active Dataset
> dataset active -x
0e080000000000010000000300001835060004001fffe00208fe7bb701f5f1125d0708fd75cbde7c6647bd0510b3914792d44f45b6c7d76eb9306eec94030f4f70656e5468726561642d35383332010258320410e35c581af5029b054fc904a24c2b27700c0402a0fff8
```
On the second device, set the active dataset from leader, and start Thread interface:
```bash
> factoryreset
... # the device will reboot
> dataset set active 0e080000000000010000000300001835060004001fffe00208fe7bb701f5f1125d0708fd75cbde7c6647bd0510b3914792d44f45b6c7d76eb9306eec94030f4f70656e5468726561642d35383332010258320410e35c581af5029b054fc904a24c2b27700c0402a0fff8
> ifconfig up
Done
> thread start
Done
# After some seconds
> state
router # child is also a valid state
Done
```
The second device has joined the Thread network as a router (or a child).
## Extension commands
You can refer to the [extension command](https://github.com/espressif/esp-thread-br/blob/main/components/esp_ot_cli_extension/README.md) about the extension commands.
The following examples are supported by `ot_cli`:
* TCP and UDP Example
* Iperf Example