kopia lustrzana https://github.com/espressif/esp-idf
190 wiersze
7.8 KiB
Markdown
190 wiersze
7.8 KiB
Markdown
| Supported Targets | ESP32 | ESP32-C3 | ESP32-C6 | ESP32-H2 | ESP32-S2 | ESP32-S3 |
|
|
| ----------------- | ----- | -------- | -------- | -------- | -------- | -------- |
|
|
|
|
# TWAI Network Example
|
|
|
|
(See the README.md file in the upper level 'examples' directory for more information about examples.)
|
|
|
|
This example demonstrates how to use the TWAI driver to program a target (ESP32, ESP32-S2, ESP32-S3 or ESP32-C3) as a TWAI node, and have the two nodes (Network Master and Network Slave) communicate on a TWAI network. The Listen Only node is optional and acts as a network monitor meaning that it only receives messages and does not influence the bus in any way (i.e. doesn't not acknowledge or send error frames).
|
|
|
|
Note that concept of master/slave in this example refers to which node initiates
|
|
and stops the transfer of a stream of data messages.
|
|
|
|
## How to use example
|
|
|
|
### Hardware Required
|
|
|
|
This example requires at least two targets (e.g., an ESP32 or ESP32-S2) to act as the Network Master and Network Slave. The third target (Listen Only) is optional. Each target must be connected to an external transceiver (e.g., a SN65HVD23X transceiver). The transceivers must then be interconnected to form a TWAI network.
|
|
|
|
The following diagram illustrates an example network:
|
|
|
|
```text
|
|
---------- ---------- --------------
|
|
| Master | | Slave | | Listen Only |
|
|
| | | | | |
|
|
| TX RX | | TX RX | | TX RX |
|
|
---------- ---------- --------------
|
|
| | | | | |
|
|
| | | | | |
|
|
---------- ---------- ----------
|
|
| D R | | D R | | D R |
|
|
| | | | | |
|
|
| VP230 | | VP230 | | VP230 |
|
|
| | | | | |
|
|
| H L | | H L | | H L |
|
|
---------- ---------- ----------
|
|
| | | | | |
|
|
| | | | | |
|
|
|--x------|-----x------|-----x------|--| H
|
|
| | |
|
|
|---------x------------x------------x--| L
|
|
|
|
```
|
|
|
|
Note: If you don't have an external transceiver, you can still run the [TWAI Self Test example](../twai_self_test/README.md)
|
|
|
|
### Configure the project
|
|
|
|
For each node in the TWAI network (i.e., Master, Slave, Listen Only)...
|
|
|
|
* Set the target of the build (where `{IDF_TARGET}` stands for the target chip such as `esp32` or `esp32s2`).
|
|
* Then run `menuconfig` to configure the example.
|
|
|
|
```sh
|
|
idf.py set-target {IDF_TARGET}
|
|
idf.py menuconfig
|
|
```
|
|
|
|
* Under `Example Configuration`, configure the pin assignments using the options `TX GPIO Number` and `RX GPIO Number` according to how the target was connected to the transceiver. By default, `TX GPIO Number` and `RX GPIO Number` are set to the following values:
|
|
* On the ESP32, `TX GPIO Number` and `RX GPIO Number` default to `21` and `22` respectively
|
|
* On other chips, `TX GPIO Number` and `RX GPIO Number` default to `0` and `2` respectively
|
|
|
|
### Build and Flash
|
|
|
|
For each node, build the project and flash it to the board, then run monitor tool to view serial output:
|
|
|
|
```sh
|
|
idf.py -p PORT flash monitor
|
|
```
|
|
|
|
(Replace PORT with the name of the serial port to use.)
|
|
|
|
(To exit the serial monitor, type ``Ctrl-]``.)
|
|
|
|
See the Getting Started Guide for full steps to configure and use ESP-IDF to build projects.
|
|
|
|
## Example Output
|
|
|
|
Network Master
|
|
|
|
```text
|
|
I (345) TWAI Master: Driver installed
|
|
I (345) TWAI Master: Driver started
|
|
I (345) TWAI Master: Transmitting ping
|
|
I (3105) TWAI Master: Transmitted start command
|
|
I (3105) TWAI Master: Received data value 339
|
|
...
|
|
I (5545) TWAI Master: Received data value 584
|
|
I (5545) TWAI Master: Transmitted stop command
|
|
I (5595) TWAI Master: Driver stopped
|
|
I (6595) TWAI Master: Driver started
|
|
I (6595) TWAI Master: Transmitting ping
|
|
I (7095) TWAI Master: Transmitted start command
|
|
I (7095) TWAI Master: Received data value 738
|
|
...
|
|
I (9535) TWAI Master: Received data value 983
|
|
I (9535) TWAI Master: Transmitted stop command
|
|
I (9585) TWAI Master: Driver stopped
|
|
I (10585) TWAI Master: Driver started
|
|
I (10585) TWAI Master: Transmitting ping
|
|
I (11085) TWAI Master: Transmitted start command
|
|
I (11085) TWAI Master: Received data value 1137
|
|
...
|
|
I (13525) TWAI Master: Received data value 1382
|
|
I (13525) TWAI Master: Transmitted stop command
|
|
I (13575) TWAI Master: Driver stopped
|
|
I (14575) TWAI Master: Driver uninstalled
|
|
```
|
|
|
|
Network Slave
|
|
|
|
```text
|
|
Slave starting in 3
|
|
Slave starting in 2
|
|
Slave starting in 1
|
|
I (6322) TWAI Slave: Driver installed
|
|
I (6322) TWAI Slave: Driver started
|
|
I (6462) TWAI Slave: Transmitted ping response
|
|
I (6712) TWAI Slave: Start transmitting data
|
|
I (6712) TWAI Slave: Transmitted data value 339
|
|
...
|
|
I (9162) TWAI Slave: Transmitted data value 584
|
|
I (9212) TWAI Slave: Transmitted stop response
|
|
I (9312) TWAI Slave: Driver stopped
|
|
I (10312) TWAI Slave: Driver started
|
|
I (10452) TWAI Slave: Transmitted ping response
|
|
I (10702) TWAI Slave: Start transmitting data
|
|
I (10702) TWAI Slave: Transmitted data value 738
|
|
...
|
|
I (13152) TWAI Slave: Transmitted data value 983
|
|
I (13202) TWAI Slave: Transmitted stop response
|
|
I (13302) TWAI Slave: Driver stopped
|
|
I (14302) TWAI Slave: Driver started
|
|
I (14442) TWAI Slave: Transmitted ping response
|
|
I (14692) TWAI Slave: Start transmitting data
|
|
I (14692) TWAI Slave: Transmitted data value 1137
|
|
...
|
|
I (17142) TWAI Slave: Transmitted data value 1382
|
|
I (17192) TWAI Slave: Transmitted stop response
|
|
I (17292) TWAI Slave: Driver stopped
|
|
I (18292) TWAI Slave: Driver uninstalled
|
|
```
|
|
|
|
Network Listen Only
|
|
|
|
```text
|
|
I (326) TWAI Listen Only: Driver installed
|
|
I (326) TWAI Listen Only: Driver started
|
|
I (366) TWAI Listen Only: Received master ping
|
|
...
|
|
I (1866) TWAI Listen Only: Received master ping
|
|
I (1866) TWAI Listen Only: Received slave ping response
|
|
I (2116) TWAI Listen Only: Received master start command
|
|
I (2116) TWAI Listen Only: Received data value 329
|
|
...
|
|
I (4566) TWAI Listen Only: Received data value 574
|
|
I (4566) TWAI Listen Only: Received master stop command
|
|
I (4606) TWAI Listen Only: Received slave stop response
|
|
I (5606) TWAI Listen Only: Received master ping
|
|
I (5856) TWAI Listen Only: Received master ping
|
|
I (5856) TWAI Listen Only: Received slave ping response
|
|
I (6106) TWAI Listen Only: Received master start command
|
|
I (6106) TWAI Listen Only: Received data value 728
|
|
...
|
|
I (8556) TWAI Listen Only: Received data value 973
|
|
I (8556) TWAI Listen Only: Received master stop command
|
|
I (8596) TWAI Listen Only: Received slave stop response
|
|
I (9596) TWAI Listen Only: Received master ping
|
|
I (9846) TWAI Listen Only: Received master ping
|
|
I (9846) TWAI Listen Only: Received slave ping response
|
|
I (10096) TWAI Listen Only: Received master start command
|
|
I (10096) TWAI Listen Only: Received data value 1127
|
|
...
|
|
I (12546) TWAI Listen Only: Received data value 1372
|
|
I (12546) TWAI Listen Only: Received master stop command
|
|
I (12586) TWAI Listen Only: Received slave stop response
|
|
I (12586) TWAI Listen Only: Driver stopped
|
|
I (12586) TWAI Listen Only: Driver uninstalled
|
|
|
|
```
|
|
|
|
## Example Breakdown
|
|
|
|
The communication between the Network Master and Network Slave execute the following steps over multiple iterations:
|
|
|
|
1. Both master and slave go through install and start their TWAI drivers independently.
|
|
2. The master repeatedly sends **PING** messages until it receives a **PING_RESP** (ping response message) from the slave. The slave will only send a **PING_RESP** message when it receives a **PING** message from the master.
|
|
3. Once the master has received the **PING_RESP** from the slave, it will send a **START_CMD** message to the slave.
|
|
4. Upon receiving the **START_CMD** message, the slave will start transmitting **DATA** messages until the master sends a **STOP_CMD**. The master will send the **STOP_CMD** after receiving N **DATA** messages from the slave (N = 50 by default).
|
|
5. When the slave receives the **STOP_CMD**, it will confirm that it has stopped by sending a **STOP_RESP** message to the master.
|