kopia lustrzana https://github.com/espressif/esp-idf
293 wiersze
11 KiB
Markdown
293 wiersze
11 KiB
Markdown
# OpenThread Border Router Example
|
|
|
|
## Overview
|
|
|
|
This example demonstrates an [OpenThread border router](https://openthread.io/guides/border-router).
|
|
|
|
## How to use example
|
|
|
|
### Hardware Required
|
|
|
|
The following SoCs are required to run this example:
|
|
* An ESP32 series Wi-Fi SoC (ESP32, ESP32-C, ESP32-S, etc) loaded with this ot_br example.
|
|
* An ESP32-H2 802.15.4 SoC loaded with [ot_rcp](../ot_rcp) example.
|
|
* Another ESP32-H2 SoC loaded with [ot_cli](../ot_cli) example. Enable `OPENTHREAD_JOINER` option in menuconfig before compiling the example.
|
|
|
|
Connect the two SoCs via UART, below is an example setup with ESP32 DevKitC and ESP32-H2 DevKitC:
|
|
![thread_br](image/thread-border-router-esp32-esp32h2.jpg)
|
|
|
|
ESP32 pin | ESP32-H2 pin
|
|
----------|-------------
|
|
GND | G
|
|
GPIO4 | TX
|
|
GPIO5 | RX
|
|
|
|
### Configure the project
|
|
|
|
```
|
|
idf.py menuconfig
|
|
```
|
|
Two ways are provided to setup the Thread Border Router in this example:
|
|
|
|
- Auto Start
|
|
Enable `OPENTHREAD_BR_AUTO_START`, configure the `CONFIG_EXAMPLE_WIFI_SSID` and `CONFIG_EXAMPLE_WIFI_PASSWORD` with your access point's ssid and psk.
|
|
The device will connect to Wi-Fi and form a Thread network automatically after bootup.
|
|
|
|
- Manual mode
|
|
Disable `OPENTHREAD_BR_AUTO_START` and enable `OPENTHREAD_CLI_ESP_EXTENSION`. `wifi` command will be added for connecting the device to the Wi-Fi network.
|
|
|
|
### Build, Flash, and Run
|
|
|
|
Build the project and flash it to the board, then run monitor tool to view serial output:
|
|
|
|
```
|
|
idf.py -p PORT build flash monitor
|
|
```
|
|
If the `OPENTHREAD_BR_AUTO_START` option is enabled, The device will be connected to the configured Wi-Fi and Thread network automatically then act as the border router.
|
|
|
|
Otherwise, you need to manually configure the networks with CLI commands.
|
|
|
|
`wifi` command can be used to configure the Wi-Fi network.
|
|
|
|
```bash
|
|
> wifi
|
|
--wifi parameter---
|
|
connect
|
|
-s : wifi ssid
|
|
-p : wifi psk
|
|
---example---
|
|
join a wifi:
|
|
ssid: threadcertAP
|
|
psk: threadcertAP : wifi connect -s threadcertAP -p threadcertAP
|
|
state : get wifi state, disconnect or connect
|
|
---example---
|
|
get wifi state : wifi state
|
|
Done
|
|
```
|
|
|
|
To join a Wi-Fi network, please use the `wifi connect` command:
|
|
|
|
```bash
|
|
> wifi connect -s threadcertAP -p threadcertAP
|
|
ssid: threadcertAP
|
|
psk: threadcertAP
|
|
I (11331) wifi:wifi driver task: 3ffd06e4, prio:23, stack:6656, core=0
|
|
I (11331) system_api: Base MAC address is not set
|
|
I (11331) system_api: read default base MAC address from EFUSE
|
|
I (11341) wifi:wifi firmware version: 45c46a4
|
|
I (11341) wifi:wifi certification version: v7.0
|
|
|
|
|
|
..........
|
|
|
|
I (13741) esp_netif_handlers: sta ip: 192.168.3.10, mask: 255.255.255.0, gw: 192.168.3.1
|
|
W (13771) wifi:<ba-add>idx:0 (ifx:0, 02:0f:c1:32:3b:2b), tid:0, ssn:2, winSize:64
|
|
wifi sta is connected successfully
|
|
Done
|
|
```
|
|
|
|
To get the state of the Wi-Fi network:
|
|
|
|
```bash
|
|
> wifi state
|
|
connected
|
|
Done
|
|
```
|
|
|
|
For forming the Thread network, please refer to the [ot_cli_README](../ot_cli/README.md).
|
|
|
|
## Example Output
|
|
|
|
```bash
|
|
I (2729) esp_netif_handlers: example_connect: sta ip: 192.168.1.100, mask: 255.255.255.0, gw: 192.168.1.1
|
|
I (2729) example_connect: Got IPv4 event: Interface "example_connect: sta" address: 192.168.1.100
|
|
I (3729) example_connect: Got IPv6 event: Interface "example_connect: sta" address: fe80:0000:0000:0000:266f:28ff:fe80:2920, type: ESP_IP6_ADDR_IS_LINK_LOCAL
|
|
I (3729) example_connect: Connected to example_connect: sta
|
|
I (3739) example_connect: - IPv4 address: 192.168.1.100
|
|
I (3739) example_connect: - IPv6 address: fe80:0000:0000:0000:266f:28ff:fe80:2920, type: ESP_IP6_ADDR_IS_LINK_LOCAL
|
|
|
|
......
|
|
|
|
|
|
I(8139) OPENTHREAD:[INFO]-MLE-----: AttachState ParentReqReeds -> Idle
|
|
I(8139) OPENTHREAD:[NOTE]-MLE-----: Allocate router id 50
|
|
I(8139) OPENTHREAD:[NOTE]-MLE-----: RLOC16 fffe -> c800
|
|
I(8159) OPENTHREAD:[NOTE]-MLE-----: Role Detached -> Leader
|
|
```
|
|
## Using the border agent feature
|
|
|
|
You need to build ot-commissioner on the host machine and another Thread end device running OpenThread cli.
|
|
|
|
You can find the guide to build and run ot-commissioner [here](https://openthread.io/guides/commissioner/build).
|
|
|
|
Make sure to configure the same PSKc as the one in sdkconfig in ot-commisioner's config file `non-ccm-config.json`
|
|
|
|
### Connect the commissioner to the border router
|
|
|
|
Note that the target address `192.168.1.100` shall match the actual Wi-Fi IP address of the device. `49154` is a port number used by the OT commissioner.
|
|
|
|
``` bash
|
|
$ commissioner-cli /usr/local/etc/commissioner/non-ccm-config.json
|
|
> start 192.168.1.100 49154
|
|
[done]
|
|
> active
|
|
true
|
|
[done]
|
|
```
|
|
|
|
You can also verify the commissioner connection from the border router's log:
|
|
|
|
```
|
|
I(59709) OPENTHREAD:[INFO]-MESH-CP-: DTLS started
|
|
I(65469) OPENTHREAD:[INFO]-MESH-CP-: Commissioner connected
|
|
I(65479) OPENTHREAD:[INFO]-MESH-CP-: Forwarded request to leader on c/lp
|
|
I(65489) OPENTHREAD:[INFO]-MESH-CP-: received petition
|
|
I(65489) OPENTHREAD:[INFO]-MESH-CP-: sent petition response
|
|
I(65489) OPENTHREAD:[INFO]-MESH-CP-: commissioner accepted: session ID=3077, ALOC=fd04:b642:9ba9:fcdc:0:ff:fe00:fc35
|
|
I(65499) OPENTHREAD:[INFO]-MESH-CP-: Sent to commissioner
|
|
I(65509) OPENTHREAD:[INFO]-CORE----: Notifier: StateChanged (0x00000201) [Ip6+ NetData]
|
|
I(65529) OPENTHREAD:[INFO]-BBR-----: PBBR state: None
|
|
I(65539) OPENTHREAD:[INFO]-BBR-----: Domain Prefix: ::/0, state: None
|
|
I(65559) OPENTHREAD:[INFO]-MESH-CP-: Forwarded request to leader on c/ag
|
|
W(65559) OPENTHREAD:[WARN]-MESH-CP-: Failed to notify commissioner on ProxyRx (c/ur): DestinationAddressFiltered
|
|
I(65579) OPENTHREAD:[INFO]-MESH-CP-: sent active dataset get response to fd04:b642:9ba9:fcdc:0:ff:fe00:c800
|
|
W(65579) OPENTHREAD:[WARN]-MESH-CP-: Failed to notify commissioner on ProxyRx (c/ur): DestinationAddressFiltered
|
|
I(65589) OPENTHREAD:[INFO]-MESH-CP-: Sent to commissioner
|
|
I(65629) OPENTHREAD:[INFO]-MESH-CP-: Forwarded request to leader on c/ag
|
|
W(65629) OPENTHREAD:[WARN]-MESH-CP-: Failed to notify commissioner on ProxyRx (c/ur): DestinationAddressFiltered
|
|
I(65649) OPENTHREAD:[INFO]-MESH-CP-: sent active dataset get response to fd04:b642:9ba9:fcdc:0:ff:fe00:c800
|
|
W(65649) OPENTHREAD:[WARN]-MESH-CP-: Failed to notify commissioner on ProxyRx (c/ur): DestinationAddressFiltered
|
|
I(65659) OPENTHREAD:[INFO]-MESH-CP-: Sent to commissioner
|
|
I(65689) OPENTHREAD:[INFO]-MESH-CP-: Proxy transmit sent to fd04:b642:9ba9:fcdc:0:ff:fe00:fc00
|
|
W(65689) OPENTHREAD:[WARN]-MESH-CP-: Failed to notify commissioner on ProxyRx (c/ur): DestinationAddressFiltered
|
|
I(65699) OPENTHREAD:[INFO]-MESH-CP-: sent pending dataset get response to fd04:b642:9ba9:fcdc:0:ff:fe00:fc35
|
|
I(65709) OPENTHREAD:[INFO]-MESH-CP-: Sent to commissioner on c/ur
|
|
I(65749) OPENTHREAD:[INFO]-MESH-CP-: Proxy transmit sent to fd04:b642:9ba9:fcdc:0:ff:fe00:fc00
|
|
W(65749) OPENTHREAD:[WARN]-MESH-CP-: Failed to notify commissioner on ProxyRx (c/ur): DestinationAddressFiltered
|
|
I(65759) OPENTHREAD:[INFO]-MESH-CP-: sent commissioning dataset set response
|
|
I(65769) OPENTHREAD:[INFO]-MESH-CP-: Sent to commissioner on c/ur
|
|
I(65769) OPENTHREAD:[INFO]-CORE----: Notifier: StateChanged (0x00000200) [NetData]
|
|
I(65789) OPENTHREAD:[INFO]-BBR-----: PBBR state: None
|
|
|
|
```
|
|
|
|
### Commission the joiner
|
|
|
|
In the OT commissioner cli, run:
|
|
``` bash
|
|
> joiner enableall meshcop J01NU5
|
|
[done]
|
|
>
|
|
```
|
|
|
|
In the joining device's cli, run:
|
|
|
|
```bash
|
|
> ifconfig up
|
|
Done
|
|
> joiner start J01NU5
|
|
Done
|
|
> Join success!
|
|
> thread start
|
|
Done
|
|
```
|
|
|
|
You can also find these log lines in the border router:
|
|
|
|
```
|
|
I(531219) OPENTHREAD:[INFO]-MESH-CP-: Received relay transmit
|
|
I(531229) OPENTHREAD:[INFO]-MESH-CP-: Received kek
|
|
I(531279) OPENTHREAD:[INFO]-MAC-----: Sent IPv6 UDP msg, len:85, chksum:14a0, to:92335c4b320830fb, sec:no, prio:net
|
|
I(531279) OPENTHREAD:[INFO]-MAC-----: src:[fe80:0:0:0:ac2f:720a:6fe4:c837]:1000
|
|
I(531289) OPENTHREAD:[INFO]-MAC-----: dst:[fe80:0:0:0:9033:5c4b:3208:30fb]:1000
|
|
I(531299) OPENTHREAD:[INFO]-MESH-CP-: Sending JOIN_ENT.ntf
|
|
I(531299) OPENTHREAD:[INFO]-MESH-CP-: Sent joiner entrust length = 161
|
|
|
|
......
|
|
|
|
I(552699) OPENTHREAD:[INFO]-MLE-----: Receive Child ID Request (fe80:0:0:0:8434:c5ec:fe9f:c088)
|
|
I(552729) OPENTHREAD:[INFO]-CORE----: [settings] Added ChildInfo {rloc:0xc801, extaddr:8634c5ecfe9fc088, timeout:240, mode:0x0f, version:3}
|
|
I(552729) OPENTHREAD:[INFO]-MLE-----: Send Child ID Response (fe80:0:0:0:8434:c5ec:fe9f:c088,0xc801)
|
|
I(552739) OPENTHREAD:[INFO]-CORE----: Notifier: StateChanged (0x00000400) [Child+]
|
|
I(552749) OPENTHREAD:[INFO]-UTIL----: Starting Child Supervision
|
|
```
|
|
|
|
The device has now joined the same Thread network based on the key set by the commissioner.
|
|
|
|
## Bidirectional IPv6 connectivity
|
|
|
|
The border router will automatically publish the prefix and the route table rule to the Wi-Fi network via ICMPv6 router advertisement packages.
|
|
|
|
### Host configuration
|
|
|
|
The automatically configure your host's route table rules you need to set these sysctl options:
|
|
|
|
Please replace `wlan0` with the real name of your Wi-Fi network interface.
|
|
```
|
|
sudo sysctl -w net/ipv6/conf/wlan0/accept_ra=2
|
|
sudo sysctl -w net/ipv6/conf/wlan0/accept_ra_rt_info_max_plen=128
|
|
```
|
|
|
|
For mobile devices, the route table rules will be automatically configured after iOS 14 and Android 8.1.
|
|
|
|
|
|
### Testing IPv6 connectivity
|
|
|
|
Now in the joining device, check the IP addresses:
|
|
|
|
```
|
|
> ipaddr
|
|
fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5
|
|
fdde:ad00:beef:0:0:ff:fe00:c402
|
|
fdde:ad00:beef:0:ad4a:9a9a:3cd6:e423
|
|
fe80:0:0:0:f011:2951:569e:9c4a
|
|
```
|
|
|
|
You'll notice an IPv6 global prefix with only on address assigned under it. This is the routable address of this Thread node.
|
|
You can ping this address on your host:
|
|
|
|
``` bash
|
|
$ ping fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5
|
|
PING fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5(fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5) 56 data bytes
|
|
64 bytes from fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5: icmp_seq=1 ttl=63 time=459 ms
|
|
64 bytes from fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5: icmp_seq=2 ttl=63 time=109 ms
|
|
64 bytes from fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5: icmp_seq=3 ttl=63 time=119 ms
|
|
64 bytes from fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5: icmp_seq=4 ttl=63 time=117 ms
|
|
```
|
|
|
|
## Service discovery
|
|
|
|
The newly introduced service registration protocol([SRP](https://datatracker.ietf.org/doc/html/draft-ietf-dnssd-srp-10)) allows devices in the Thread network to register a service. The border router will forward the service to the Wi-Fi network via mDNS.
|
|
|
|
Now we'll publish the service `my-service._test._udp` with hostname `test0` and port 12345
|
|
|
|
```
|
|
> srp client host name test0
|
|
Done
|
|
> srp client host address fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5
|
|
Done
|
|
> srp client service add my-service _test._udp 12345
|
|
Done
|
|
> srp client autostart enable
|
|
Done
|
|
```
|
|
|
|
This service will also become visible on the Wi-Fi network:
|
|
|
|
```bash
|
|
$ avahi-browse -r _test._udp -t
|
|
|
|
+ enp1s0 IPv6 my-service _test._udp local
|
|
= enp1s0 IPv6 my-service _test._udp local
|
|
hostname = [test0.local]
|
|
address = [fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5]
|
|
port = [12345]
|
|
txt = []
|
|
+ enp1s0 IPv4 my-service _test._udp local
|
|
= enp1s0 IPv4 my-service _test._udp local
|
|
hostname = [test0.local]
|
|
address = [fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5]
|
|
port = [12345]
|
|
txt = []
|
|
```
|