kopia lustrzana https://github.com/espressif/esp-idf
56 wiersze
2.6 KiB
Markdown
56 wiersze
2.6 KiB
Markdown
| Supported Targets | ESP32 | ESP32-C2 | ESP32-C3 | ESP32-C6 | ESP32-H2 | ESP32-P4 | ESP32-S2 | ESP32-S3 |
|
|
| ----------------- | ----- | -------- | -------- | -------- | -------- | -------- | -------- | -------- |
|
|
|
|
# HAL I2C test
|
|
|
|
This code demonstrates how to use hal functions to write an I2C master driver.
|
|
|
|
Note: This test is a pure hal i2c test. It CANNOT work with i2c driver in `esp_driver_i2c`.
|
|
|
|
## Overview
|
|
|
|
This test demonstrates basic usage of HAL (Hardware Abstract Layer) functions to write a simplest I2C master driver. This driver only relies on the I2C, GPIO and XTAL hardware features. Therefore, it can work on a bare metal environment, without any interrupt or memory allocation support. This example shows:
|
|
1. How to write an I2C driver for bare metal applications, such as in a bootloader.
|
|
2. How to use IDF HAL functions if you want to use the hardware I2C component to any 3rd party system or application.
|
|
|
|
Restricted by source we can use, this test focuses on the usage of hal functions instead of providing perfect APIs. You can arrange better APIs based on your application usage.
|
|
|
|
## How to use test
|
|
|
|
### Hardware Required
|
|
|
|
To run this test, you should have one ESP32, ESP32-S, ESP32-C, ESP32-P or ESP32-H based development board, call functions you can see the correct result. If possible, you can also see wave on logic analyzer or oscilloscope.
|
|
|
|
#### Pin Assignment:
|
|
|
|
**Note:** The following pin assignments are used by default, you can change these in the `menuconfig` .
|
|
|
|
| | SDA | SCL |
|
|
| ---------------- | -------------- | -------------- |
|
|
| ESP I2C Master | I2C_MASTER_SDA | I2C_MASTER_SCL |
|
|
| DEVICE1 | SDA | SCL |
|
|
| DEVICEn | SDA | SCL |
|
|
|
|
For the actual default value of `I2C_MASTER_SDA` and `I2C_MASTER_SCL` see `test Configuration` in `menuconfig`.
|
|
|
|
**Note:** There's no need to add an external pull-up resistors for SDA/SCL pin, because the driver will enable the internal pull-up resistors.
|
|
|
|
### Build and Flash
|
|
|
|
Enter `idf.py -p PORT flash monitor` to build, flash and monitor the project.
|
|
|
|
(To exit the serial monitor, type ``Ctrl-]``.)
|
|
|
|
See the [Getting Started Guide](https://docs.espressif.com/projects/esp-idf/en/latest/get-started/index.html) for full steps to configure and use ESP-IDF to build projects.
|
|
|
|
## test Output
|
|
|
|
```bash
|
|
I (300) hal_i2c_main: HAL I2C initialized successfully
|
|
I (320) hal_i2c_main: HAL I2C write-read successfully
|
|
```
|
|
|
|
## Troubleshooting
|
|
|
|
(For any technical queries, please open an [issue](https://github.com/espressif/esp-idf/issues) on GitHub. We will get back to you as soon as possible.)
|