9.1 KiB
OpenThread command line example
Overview
This example demonstrates an OpenThread border router.
How to use example
Hardware connection
To run this example, it's used to use an DevKit C board and connect PIN4 and PIN5 to the UART TX and RX port of another 15.4 capable radio co-processor (RCP)
Configure the project
idf.py menuconfig
You need to configure the CONFIG_EXAMPLE_WIFI_SSID
and CONFIG_EXAMPLE_WIFI_PASSWORD
with your access point's ssid and psk.
Build, Flash, and Run
Build the project and flash it to the board, then run monitor tool to view serial output:
idf.py -p PORT build flash monitor
Example Output
I (2729) esp_netif_handlers: example_connect: sta ip: 192.168.1.100, mask: 255.255.255.0, gw: 192.168.1.1
I (2729) example_connect: Got IPv4 event: Interface "example_connect: sta" address: 192.168.1.100
I (3729) example_connect: Got IPv6 event: Interface "example_connect: sta" address: fe80:0000:0000:0000:266f:28ff:fe80:2920, type: ESP_IP6_ADDR_IS_LINK_LOCAL
I (3729) example_connect: Connected to example_connect: sta
I (3739) example_connect: - IPv4 address: 192.168.1.100
I (3739) example_connect: - IPv6 address: fe80:0000:0000:0000:266f:28ff:fe80:2920, type: ESP_IP6_ADDR_IS_LINK_LOCAL
......
I(8139) OPENTHREAD:[INFO]-MLE-----: AttachState ParentReqReeds -> Idle
I(8139) OPENTHREAD:[NOTE]-MLE-----: Allocate router id 50
I(8139) OPENTHREAD:[NOTE]-MLE-----: RLOC16 fffe -> c800
I(8159) OPENTHREAD:[NOTE]-MLE-----: Role Detached -> Leader
The device will automatically connect to the configured WiFi and Thread network and act as the border router.
Using the border agent feature
You need to ot-commissioner on the host machine and another Thread end device running OpenThread cli.
You can find the guide to build and run ot-commissioner here.
Make sure to configure the same PSKc as the one in sdkconfig in ot-commisioner's config file non-ccm-config.json
Connect the commissioner to the border router
Note that the target address 192.168.1.100
shall match the actual WiFi IP address of the device.
$ commissioner-cli /usr/local/etc/commissioner/non-ccm-config.json
> start 192.168.1.100 49154
[done]
> active
true
[done]
You can also verify the commissioner connection from the border router's log:
I(59709) OPENTHREAD:[INFO]-MESH-CP-: DTLS started
I(65469) OPENTHREAD:[INFO]-MESH-CP-: Commissioner connected
I(65479) OPENTHREAD:[INFO]-MESH-CP-: Forwarded request to leader on c/lp
I(65489) OPENTHREAD:[INFO]-MESH-CP-: received petition
I(65489) OPENTHREAD:[INFO]-MESH-CP-: sent petition response
I(65489) OPENTHREAD:[INFO]-MESH-CP-: commissioner accepted: session ID=3077, ALOC=fd04:b642:9ba9:fcdc:0:ff:fe00:fc35
I(65499) OPENTHREAD:[INFO]-MESH-CP-: Sent to commissioner
I(65509) OPENTHREAD:[INFO]-CORE----: Notifier: StateChanged (0x00000201) [Ip6+ NetData]
I(65529) OPENTHREAD:[INFO]-BBR-----: PBBR state: None
I(65539) OPENTHREAD:[INFO]-BBR-----: Domain Prefix: ::/0, state: None
I(65559) OPENTHREAD:[INFO]-MESH-CP-: Forwarded request to leader on c/ag
W(65559) OPENTHREAD:[WARN]-MESH-CP-: Failed to notify commissioner on ProxyRx (c/ur): DestinationAddressFiltered
I(65579) OPENTHREAD:[INFO]-MESH-CP-: sent active dataset get response to fd04:b642:9ba9:fcdc:0:ff:fe00:c800
W(65579) OPENTHREAD:[WARN]-MESH-CP-: Failed to notify commissioner on ProxyRx (c/ur): DestinationAddressFiltered
I(65589) OPENTHREAD:[INFO]-MESH-CP-: Sent to commissioner
I(65629) OPENTHREAD:[INFO]-MESH-CP-: Forwarded request to leader on c/ag
W(65629) OPENTHREAD:[WARN]-MESH-CP-: Failed to notify commissioner on ProxyRx (c/ur): DestinationAddressFiltered
I(65649) OPENTHREAD:[INFO]-MESH-CP-: sent active dataset get response to fd04:b642:9ba9:fcdc:0:ff:fe00:c800
W(65649) OPENTHREAD:[WARN]-MESH-CP-: Failed to notify commissioner on ProxyRx (c/ur): DestinationAddressFiltered
I(65659) OPENTHREAD:[INFO]-MESH-CP-: Sent to commissioner
I(65689) OPENTHREAD:[INFO]-MESH-CP-: Proxy transmit sent to fd04:b642:9ba9:fcdc:0:ff:fe00:fc00
W(65689) OPENTHREAD:[WARN]-MESH-CP-: Failed to notify commissioner on ProxyRx (c/ur): DestinationAddressFiltered
I(65699) OPENTHREAD:[INFO]-MESH-CP-: sent pending dataset get response to fd04:b642:9ba9:fcdc:0:ff:fe00:fc35
I(65709) OPENTHREAD:[INFO]-MESH-CP-: Sent to commissioner on c/ur
I(65749) OPENTHREAD:[INFO]-MESH-CP-: Proxy transmit sent to fd04:b642:9ba9:fcdc:0:ff:fe00:fc00
W(65749) OPENTHREAD:[WARN]-MESH-CP-: Failed to notify commissioner on ProxyRx (c/ur): DestinationAddressFiltered
I(65759) OPENTHREAD:[INFO]-MESH-CP-: sent commissioning dataset set response
I(65769) OPENTHREAD:[INFO]-MESH-CP-: Sent to commissioner on c/ur
I(65769) OPENTHREAD:[INFO]-CORE----: Notifier: StateChanged (0x00000200) [NetData]
I(65789) OPENTHREAD:[INFO]-BBR-----: PBBR state: None
Commission the joiner
In the OT commissioner cli, run:
> joiner enableall meshcop J01NU5
[done]
>
In the joining device's cli, run:
> ifconfig up
Done
> joiner start J01NU5
Done
> Join success!
> thread start
Done
You can also find these log lines in the border router:
I(531219) OPENTHREAD:[INFO]-MESH-CP-: Received relay transmit
I(531229) OPENTHREAD:[INFO]-MESH-CP-: Received kek
I(531279) OPENTHREAD:[INFO]-MAC-----: Sent IPv6 UDP msg, len:85, chksum:14a0, to:92335c4b320830fb, sec:no, prio:net
I(531279) OPENTHREAD:[INFO]-MAC-----: src:[fe80:0:0:0:ac2f:720a:6fe4:c837]:1000
I(531289) OPENTHREAD:[INFO]-MAC-----: dst:[fe80:0:0:0:9033:5c4b:3208:30fb]:1000
I(531299) OPENTHREAD:[INFO]-MESH-CP-: Sending JOIN_ENT.ntf
I(531299) OPENTHREAD:[INFO]-MESH-CP-: Sent joiner entrust length = 161
......
I(552699) OPENTHREAD:[INFO]-MLE-----: Receive Child ID Request (fe80:0:0:0:8434:c5ec:fe9f:c088)
I(552729) OPENTHREAD:[INFO]-CORE----: [settings] Added ChildInfo {rloc:0xc801, extaddr:8634c5ecfe9fc088, timeout:240, mode:0x0f, version:3}
I(552729) OPENTHREAD:[INFO]-MLE-----: Send Child ID Response (fe80:0:0:0:8434:c5ec:fe9f:c088,0xc801)
I(552739) OPENTHREAD:[INFO]-CORE----: Notifier: StateChanged (0x00000400) [Child+]
I(552749) OPENTHREAD:[INFO]-UTIL----: Starting Child Supervision
The device has now joined the same Thread network based on the key set by the commissioner.
Bidirectional IPv6 connectivity
The border router will automatically publish the prefix and the route table rule to the WiFi network via ICMPv6 router advertisment packages.
Host configuration
The automatically configure your host's route table rules you need to set these sysctl options:
Please relace wlan0
with the real name of your WiFi network interface.
sudo sysctl -w net/ipv6/conf/wlan0/accept_ra=2
sudo sysctl -w net/ipv6/conf/wlan0/accept_ra_rt_info_max_plen=128
For mobile devices, the route table rules will be automatically configured after iOS 14 and Android 8.1.
Testing IPv6 connecitivity
Now in the joining device, check the IP addresses:
> ipaddr
fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5
fdde:ad00:beef:0:0:ff:fe00:c402
fdde:ad00:beef:0:ad4a:9a9a:3cd6:e423
fe80:0:0:0:f011:2951:569e:9c4a
You'll notice an IPv6 global prefix with only on address assigned under it. This is the routable address of this Thread node. You can ping this address on your host:
$ ping fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5
PING fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5(fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5) 56 data bytes
64 bytes from fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5: icmp_seq=1 ttl=63 time=459 ms
64 bytes from fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5: icmp_seq=2 ttl=63 time=109 ms
64 bytes from fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5: icmp_seq=3 ttl=63 time=119 ms
64 bytes from fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5: icmp_seq=4 ttl=63 time=117 ms
Service discovery
The newly introduced service registration protocol(SRP) allows devices in the Thread network to register a service. The border router will forward the service to the WiFi network via mDNS.
Now we'll publish the service my-service._test._udp
with hostname test0
and port 12345
> srp client host name test0
Done
> srp client host address fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5
Done
> srp client service add my-service _test._udp 12345
Done
> srp client autostart enable
Done
This service will also become visible on the WiFi network:
$ avahi-browse -r _test._udp -t
+ enp1s0 IPv6 my-service _test._udp local
= enp1s0 IPv6 my-service _test._udp local
hostname = [test0.local]
address = [fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5]
port = [12345]
txt = []
+ enp1s0 IPv4 my-service _test._udp local
= enp1s0 IPv4 my-service _test._udp local
hostname = [test0.local]
address = [fde6:75ff:def4:3bc3:9e9e:3ef:4245:28b5]
port = [12345]
txt = []