kopia lustrzana https://github.com/jgromes/RadioLib
76 wiersze
2.0 KiB
C++
76 wiersze
2.0 KiB
C++
/*
|
|
KiteLib RF69 Transmit with AES Example
|
|
|
|
This example transmits packets using RF69 FSK radio module.
|
|
Packets are encrypted using hardware AES.
|
|
NOTE: When using address filtering, the address byte is NOT encrypted!
|
|
*/
|
|
|
|
// include the library
|
|
#include <KiteLib.h>
|
|
|
|
// RF69 module is in slot A on the shield
|
|
RF69 rf = Kite.ModuleA;
|
|
|
|
void setup() {
|
|
Serial.begin(9600);
|
|
|
|
// initialize RF69 with default settings
|
|
Serial.print(F("[RF69] Initializing ... "));
|
|
// carrier frequency: 434.0 MHz
|
|
// bit rate: 48.0 kbps
|
|
// Rx bandwidth: 125.0 kHz
|
|
// frequency deviation: 50.0 kHz
|
|
// output power: 13 dBm
|
|
// sync word: 0x2D 0x01
|
|
int state = rf.begin();
|
|
if (state == ERR_NONE) {
|
|
Serial.println(F("success!"));
|
|
} else {
|
|
Serial.print(F("failed, code "));
|
|
Serial.println(state);
|
|
while (true);
|
|
}
|
|
|
|
// set AES key to encrypt the packet
|
|
// NOTE: the key must be exactly 16 bytes long!
|
|
uint8_t key[] = {0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07,
|
|
0x08, 0x09, 0x0A, 0x0B, 0x0C, 0x0D, 0x0E, 0x0F
|
|
};
|
|
rf.setAESKey(key);
|
|
|
|
// enable AES encryption
|
|
rf.enableAES();
|
|
|
|
// AES encryption can also be disabled
|
|
/*
|
|
rf.disableAES();
|
|
*/
|
|
}
|
|
|
|
void loop() {
|
|
Serial.print(F("[RF69] Transmitting packet ... "));
|
|
|
|
// you can transmit C-string or Arduino string up to 64 characters long
|
|
int state = rf.transmit("Hello World!");
|
|
|
|
// you can also transmit byte array up to 64 bytes long
|
|
/*
|
|
byte byteArr[] = {0x01, 0x23, 0x45, 0x67, 0x89, 0xAB, 0xCD, 0xEF};
|
|
int state = rf.transmit(byteArr, 8);
|
|
*/
|
|
|
|
if (state == ERR_NONE) {
|
|
// the packet was successfully transmitted
|
|
Serial.println(" success!");
|
|
|
|
} else if (state == ERR_PACKET_TOO_LONG) {
|
|
// the supplied packet was longer than 256 bytes
|
|
Serial.println(" too long!");
|
|
|
|
}
|
|
|
|
// wait for a second before transmitting again
|
|
delay(1000);
|
|
}
|