kopia lustrzana https://github.com/jgromes/RadioLib
82 wiersze
2.1 KiB
C++
82 wiersze
2.1 KiB
C++
/*
|
|
KiteLib RF69 Receive with AES Example
|
|
|
|
This example receives packets using RF69 FSK radio module.
|
|
Packets are decrypted using hardware AES.
|
|
NOTE: When using address filtering, the address byte is NOT encrypted!
|
|
*/
|
|
|
|
// include the library
|
|
#include <KiteLib.h>
|
|
|
|
// RF69 module is in slot A on the shield
|
|
RF69 rf = Kite.ModuleA;
|
|
|
|
void setup() {
|
|
Serial.begin(9600);
|
|
|
|
// initialize RF69 with default settings
|
|
Serial.print(F("[RF69] Initializing ... "));
|
|
// carrier frequency: 434.0 MHz
|
|
// bit rate: 48.0 kbps
|
|
// Rx bandwidth: 125.0 kHz
|
|
// frequency deviation: 50.0 kHz
|
|
// output power: 13 dBm
|
|
// sync word: 0x2D 0x01
|
|
int state = rf.begin();
|
|
if (state == ERR_NONE) {
|
|
Serial.println(F("success!"));
|
|
} else {
|
|
Serial.print(F("failed, code "));
|
|
Serial.println(state);
|
|
while (true);
|
|
}
|
|
|
|
// set AES key that will be used to decrypt the packet
|
|
// NOTE: the key must be exactly 16 bytes long!
|
|
uint8_t key[] = {0x00, 0x01, 0x02, 0x03, 0x04, 0x05, 0x06, 0x07,
|
|
0x08, 0x09, 0x0A, 0x0B, 0x0C, 0x0D, 0x0E, 0x0F
|
|
};
|
|
rf.setAESKey(key);
|
|
|
|
// enable AES encryption
|
|
rf.enableAES();
|
|
|
|
// AES encryption can also be disabled
|
|
/*
|
|
rf.disableAES();
|
|
*/
|
|
}
|
|
|
|
void loop() {
|
|
Serial.print(F("[RF69] Waiting for incoming transmission ... "));
|
|
|
|
// you can receive data as an Arduino String
|
|
String str;
|
|
int state = rf.receive(str);
|
|
|
|
// you can also receive data as byte array
|
|
/*
|
|
byte byteArr[8];
|
|
int state = rf.receive(byteArr, 8);
|
|
*/
|
|
|
|
if (state == ERR_NONE) {
|
|
// packet was successfully received
|
|
Serial.println(F("success!"));
|
|
|
|
// print the data of the packet
|
|
Serial.print(F("[RF69] Data:\t\t"));
|
|
Serial.println(str);
|
|
|
|
} else if (state == ERR_RX_TIMEOUT) {
|
|
// timeout occurred while waiting for a packet
|
|
Serial.println(F("timeout!"));
|
|
|
|
} else if (state == ERR_CRC_MISMATCH) {
|
|
// packet was received, but is malformed
|
|
Serial.println(F("CRC error!"));
|
|
|
|
}
|
|
}
|