[LR11x0] Added ping-pong example

examples/LR11x0/LR11x0_PingPong/LR11x0_PingPong.ino

@@ -0,0 +1,166 @@
+/*
+   RadioLib LR11x0 Ping-Pong Example
+
+   For default module settings, see the wiki page
+   https://github.com/jgromes/RadioLib/wiki/Default-configuration#lr11x0---lora-modem
+
+   For full API reference, see the GitHub Pages
+   https://jgromes.github.io/RadioLib/
+*/
+
+// include the library
+#include <RadioLib.h>
+
+// uncomment the following only on one
+// of the nodes to initiate the pings
+//#define INITIATING_NODE
+
+// LR1110 has the following connections:
+// NSS pin:   10
+// IRQ pin:   2
+// NRST pin:  3
+// BUSY pin:  9
+LR1110 radio = new Module(10, 2, 3, 9);
+
+// set RF switch configuration for Wio WM1110
+// Wio WM1110 uses DIO5 and DIO6 for RF switching
+// NOTE: other boards may be different!
+static const uint32_t rfswitch_dio_pins[] = { 
+  RADIOLIB_LR11X0_DIO5, RADIOLIB_LR11X0_DIO6,
+  RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC
+};
+
+static const Module::RfSwitchMode_t rfswitch_table[] = {
+  // mode                  DIO5  DIO6 
+  { LR11x0::MODE_STBY,   { LOW,  LOW  } },
+  { LR11x0::MODE_RX,     { HIGH, LOW  } },
+  { LR11x0::MODE_TX,     { HIGH, HIGH } },
+  { LR11x0::MODE_TX_HP,  { LOW,  HIGH } },
+  { LR11x0::MODE_TX_HF,  { LOW,  LOW  } },
+  { LR11x0::MODE_GNSS,   { LOW,  LOW  } },
+  { LR11x0::MODE_WIFI,   { LOW,  LOW  } },
+  END_OF_MODE_TABLE,
+};
+
+// save transmission states between loops
+int transmissionState = RADIOLIB_ERR_NONE;
+
+// flag to indicate transmission or reception state
+bool transmitFlag = false;
+
+// flag to indicate that a packet was sent or received
+volatile bool operationDone = false;
+
+// this function is called when a complete packet
+// is transmitted or received by the module
+// IMPORTANT: this function MUST be 'void' type
+//            and MUST NOT have any arguments!
+#if defined(ESP8266) || defined(ESP32)
+  ICACHE_RAM_ATTR
+#endif
+void setFlag(void) {
+  // we sent or received a packet, set the flag
+  operationDone = true;
+}
+
+void setup() {
+  Serial.begin(9600);
+
+  // set RF switch control configuration
+  // this has to be done prior to calling begin()
+  radio.setRfSwitchTable(rfswitch_dio_pins, rfswitch_table);
+
+  // initialize LR1110 with default settings
+  Serial.print(F("[LR1110] Initializing ... "));
+  int state = radio.begin();
+  if (state == RADIOLIB_ERR_NONE) {
+    Serial.println(F("success!"));
+  } else {
+    Serial.print(F("failed, code "));
+    Serial.println(state);
+    while (true) { delay(10); }
+  }
+
+  // set the function that will be called
+  // when new packet is received
+  radio.setIrqAction(setFlag);
+
+  #if defined(INITIATING_NODE)
+    // send the first packet on this node
+    Serial.print(F("[LR1110] Sending first packet ... "));
+    transmissionState = radio.startTransmit("Hello World!");
+    transmitFlag = true;
+  #else
+    // start listening for LoRa packets on this node
+    Serial.print(F("[LR1110] Starting to listen ... "));
+    state = radio.startReceive();
+    if (state == RADIOLIB_ERR_NONE) {
+      Serial.println(F("success!"));
+    } else {
+      Serial.print(F("failed, code "));
+      Serial.println(state);
+      while (true) { delay(10); }
+    }
+  #endif
+}
+
+void loop() {
+  // check if the previous operation finished
+  if(operationDone) {
+    // reset flag
+    operationDone = false;
+
+    if(transmitFlag) {
+      // the previous operation was transmission, listen for response
+      // print the result
+      if (transmissionState == RADIOLIB_ERR_NONE) {
+        // packet was successfully sent
+        Serial.println(F("transmission finished!"));
+
+      } else {
+        Serial.print(F("failed, code "));
+        Serial.println(transmissionState);
+
+      }
+
+      // listen for response
+      radio.startReceive();
+      transmitFlag = false;
+
+    } else {
+      // the previous operation was reception
+      // print data and send another packet
+      String str;
+      int state = radio.readData(str);
+
+      if (state == RADIOLIB_ERR_NONE) {
+        // packet was successfully received
+        Serial.println(F("[LR1110] Received packet!"));
+
+        // print data of the packet
+        Serial.print(F("[LR1110] Data:\t\t"));
+        Serial.println(str);
+
+        // print RSSI (Received Signal Strength Indicator)
+        Serial.print(F("[LR1110] RSSI:\t\t"));
+        Serial.print(radio.getRSSI());
+        Serial.println(F(" dBm"));
+
+        // print SNR (Signal-to-Noise Ratio)
+        Serial.print(F("[LR1110] SNR:\t\t"));
+        Serial.print(radio.getSNR());
+        Serial.println(F(" dB"));
+
+      }
+
+      // wait a second before transmitting again
+      delay(1000);
+
+      // send another one
+      Serial.print(F("[LR1110] Sending another packet ... "));
+      transmissionState = radio.startTransmit("Hello World!");
+      transmitFlag = true;
+    }
+  
+  }
+}