OpenRTX/platform/targets/DM-1701/platform.c

238 wiersze
6.2 KiB
C

/***************************************************************************
* Copyright (C) 2023 - 2025 by Federico Amedeo Izzo IU2NUO, *
* Niccolò Izzo IU2KIN, *
* Frederik Saraci IU2NRO *
* Silvano Seva IU2KWO *
* *
* This program is free software; you can redistribute it and/or modify *
* it under the terms of the GNU General Public License as published by *
* the Free Software Foundation; either version 3 of the License, or *
* (at your option) any later version. *
* *
* This program is distributed in the hope that it will be useful, *
* but WITHOUT ANY WARRANTY; without even the implied warranty of *
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the *
* GNU General Public License for more details. *
* *
* You should have received a copy of the GNU General Public License *
* along with this program; if not, see <http://www.gnu.org/licenses/> *
***************************************************************************/
#include <interfaces/platform.h>
#include <peripherals/gpio.h>
#include <hwconfig.h>
#include <string.h>
#include <calibInfo_MDx.h>
#include <interfaces/nvmem.h>
#include <toneGenerator_MDx.h>
#include <peripherals/rtc.h>
#include <interfaces/audio.h>
#include <chSelector.h>
#include <adc_stm32.h>
#include <Cx000_dac.h>
#ifdef ENABLE_BKLIGHT_DIMMING
#include <backlight.h>
#endif
static const hwInfo_t hwInfo =
{
.vhf_maxFreq = 174,
.vhf_minFreq = 136,
.vhf_band = 1,
.uhf_maxFreq = 470,
.uhf_minFreq = 400,
.uhf_band = 1,
.hw_version = 0,
.name = "DM-1701"
};
void platform_init()
{
/* Configure GPIOs */
gpio_setMode(GREEN_LED, OUTPUT);
gpio_setMode(RED_LED, OUTPUT);
gpio_setMode(PTT_SW, INPUT_PULL_UP);
gpio_setMode(PTT_EXT, INPUT_PULL_UP);
#ifndef RUNNING_TESTSUITE
gpio_setMode(PWR_SW, OUTPUT);
gpio_setPin(PWR_SW);
#endif
adcStm32_init(&adc1);
nvm_init(); /* Initialise non volatile memory manager */
toneGen_init(); /* Initialise tone generator */
rtc_init(); /* Initialise RTC */
chSelector_init(); /* Initialise channel selector handler */
audio_init(); /* Initialise audio management module */
#ifdef ENABLE_BKLIGHT_DIMMING
backlight_init(); /* Initialise backlight driver */
#else
gpio_setMode(LCD_BKLIGHT, OUTPUT);
gpio_clearPin(LCD_BKLIGHT);
#endif
}
void platform_terminate()
{
/* Shut down backlight */
#ifdef ENABLE_BKLIGHT_DIMMING
backlight_terminate();
#else
gpio_clearPin(LCD_BKLIGHT);
#endif
/* Shut down LEDs */
gpio_clearPin(GREEN_LED);
gpio_clearPin(RED_LED);
/* Shut down all the modules */
adcStm32_init(&adc1);
nvm_terminate();
toneGen_terminate();
chSelector_terminate();
audio_terminate();
/* Finally, remove power supply */
gpio_clearPin(PWR_SW);
}
uint16_t platform_getVbat()
{
/*
* Battery voltage is measured through an 1:3.26 voltage divider and
* adc_getVoltage returns a value in uV.
*/
uint32_t vbat = adc_getVoltage(&adc1, ADC_VBAT_CH) * 326;
return vbat / 100000;
}
uint8_t platform_getMicLevel()
{
/* Value from ADC is 12 bit wide: shift right by four to get 0 - 255 */
return adc_getRawSample(&adc1, ADC_MIC_CH) >> 4;
}
uint8_t platform_getVolumeLevel()
{
/*
* Volume level corresponds to an analog signal in the range 20 - 1650mV.
* Potentiometer has pseudo-logarithmic law, well described with two straight
* lines with a breakpoint around 270mV.
* Output value has range 0 - 255 with breakpoint at 150.
*/
uint16_t value = adc_getVoltage(&adc1, ADC_VOL_CH) / 1000;
uint32_t output;
if(value < 20)
return 0;
if(value <= 270)
{
// First line: offset zero, slope 0.556
output = value;
output = (output * 556) / 1000;
}
else
{
// Second line: offset 270, slope 0.076
output = value - 270;
output = (output * 76) / 1000;
output += 150;
}
if(output > 255)
output = 255;
return output;
}
bool platform_getPttStatus()
{
/* PTT line has a pullup resistor with PTT switch closing to ground */
uint8_t intPttStatus = gpio_readPin(PTT_SW);
uint8_t extPttStatus = gpio_readPin(PTT_EXT);
return ((intPttStatus == 0) || (extPttStatus == 0)) ? true : false;
}
bool platform_pwrButtonStatus()
{
/*
* When power knob is set to off, battery voltage measurement returns 0V.
* Here we set the threshold to 1V since, with knob in off position, there
* is always a bit of noise in the ADC measurement making the returned
* voltage not to be exactly zero.
*/
return (platform_getVbat() > 1000) ? true : false;
}
void platform_ledOn(led_t led)
{
switch(led)
{
case GREEN:
gpio_setPin(GREEN_LED);
break;
case RED:
gpio_setPin(RED_LED);
break;
default:
break;
}
}
void platform_ledOff(led_t led)
{
switch(led)
{
case GREEN:
gpio_clearPin(GREEN_LED);
break;
case RED:
gpio_clearPin(RED_LED);
break;
default:
break;
}
}
void platform_beepStart(uint16_t freq)
{
Cx000dac_startBeep(freq);
}
void platform_beepStop()
{
Cx000dac_stopBeep();
}
datetime_t platform_getCurrentTime()
{
return rtc_getTime();
}
void platform_setTime(datetime_t t)
{
rtc_setTime(t);
}
const hwInfo_t *platform_getHwInfo()
{
return &hwInfo;
}
/*
* NOTE: implementation of this API function is provided in
* platform/drivers/chSelector/chSelector_UV3x0.c
*/
// int8_t platform_getChSelector()