Below you will find instructions for some common use cases.
Creating High Quality Orthophotos
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
..figure:: images/orthophoto.png
:alt:image of OpenDroneMap orthophoto
:align:center
Without any parameter tweaks, ODM chooses a good compromise between quality, speed and memory usage. If you want to get higher quality results, you need to tweak some parameters:
*``--orthophoto-resolution`` is the resolution of the orthophoto in cm/pixel. Decrease this value for a higher resolution result.
*``--ignore-gsd`` is a flag that instructs ODM to skip certain memory and speed optimizations that directly affect the orthophoto. Using this flag will increase runtime and memory usage, but will produce sharper results.
*``--texturing-nadir-weight`` should be increased to ``29-32`` in urban areas to reconstruct better edges of roofs. It should be decreased to ``0-6`` in grassy / flat areas.
*``--texturing-data-term`` should be set to `area` in forest areas.
*``--mesh-size`` should be increased to `300000-600000` and `--mesh-octree-depth`` should be increased to `10-11` in urban areas to recreate better buildings / roofs.
Camera calibration is a special challenge with commodity cameras. Temperature changes, vibrations, focus, and other factors can affect the derived parameters with substantial effects on resulting data. Automatic or self calibration is possible and desirable with drone flights, but depending on the flight pattern, automatic calibration may not remove all distortion from the resulting products. James and Robson (2014) in their paper `Mitigating systematic error in topographic models derived from UAV and ground‐based image networks <https://onlinelibrary.wiley.com/doi/full/10.1002/esp.3609>`_ address how to minimize the distortion from self-calibration.
..figure:: images/msimbasi_bowling.png
:alt:image of lens distortion effect on bowling of data
*Bowling effect on point cloud over 13,000+ image dataset collected by World Bank Tanzania over the flood prone Msimbasi Basin, Dar es Salaam, Tanzania.*
To mitigate this effect, there are a few options but the simplest are as follows: fly two patterns separated by 20°, and rather than having a nadir (straight down pointing) camera, use one that tilts forward by 5°.
As this approach to flying can be take longer than typical flights, a pilot or team can fly a small area using the above approach. OpenDroneMap will generate a calibration file called cameras.json that then can be imported to be used to calibrate another flight that is more efficiently flown.
Alternatively, the following experimental method can be applied: fly with much lower overlap, but two *crossgrid* flights (sometimes called crosshatch) separated by 20° with a 5° forward facing camera.
* Crossgrid overlap percentages can be lower than parallel flights. To get good 3D results, you will require 68% overlap and sidelap for an equivalent 83% overlap and sidelap.
* To get good 2D and 2.5D (digital elevation model) results, you will require 42% overlap and sidelap for an equivalent 70% overlap and sidelap.
By default ODM does not create DEMs. To create a digital terrain model, make sure to pass the ``--dtm`` flag. To create a digital surface model, be sure to pass the ``--dsm`` flag.
..figure:: images/digitalsurfacemodel.png
:alt:image of OpenDroneMap derived digital surface model
:align:center
For DTM generation, a Simple Morphological Filter (smrf) is used to classify points in ground vs. non-ground and only the ground points are used. The ``smrf`` filter can be controlled via several parameters:
*``--smrf-scalar`` scaling value. Increase this parameter for terrains with lots of height variation.
*``--smrf-slope`` slope parameter, which is a measure of "slope tolerance". Increase this parameter for terrains with lots of height variation. Should be set to something higher than 0.1 and not higher than 1.2.
*``--smrf-threshold`` elevation threshold. Set this parameter to the minimum height (in meters) that you expect non-ground objects to be.
*``--smrf-window`` window radius parameter (in meters) that corresponds to the size of the largest feature (building, trees, etc.) to be removed. Should be set to a value higher than 10.
Changing these options can affect the result of DTMs significantly. The best source to read to understand how the parameters affect the output is to read the original paper `An improved simple morphological filter for the terrain classification of airborne LIDAR data <https://www.researchgate.net/publication/258333806_An_Improved_Simple_Morphological_Filter_for_the_Terrain_Classification_of_Airborne_LIDAR_Data>`_ (PDF freely available).
Overall the ``--smrf-threshold`` option has the biggest impact on results.
SMRF is good at avoiding Type I errors (small number of ground points mistakenly classified as non-ground) but only "acceptable" at avoiding Type II errors (large number non-ground points mistakenly classified as ground). This needs to be taken in consideration when generating DTMs that are meant to be used visually, since objects mistaken for ground look like artifacts in the final DTM.
..figure:: images/smrf.png
:alt:image of lens distortion effect on bowling of data
:align:center
Two other important parameters affect DEM generation:
*``--dem-resolution`` which sets the output resolution of the DEM raster (cm/pixel)
*``--dem-gapfill-steps`` which determines the number of progressive DEM layers to use. For urban scenes increasing this value to `4-5` can help produce better interpolation results in the areas that are left empty by the SMRF filter.
WGS84, UTM, and proj4 geospatial coordinates are supported. For more information about the file format read the `Ground Control Points Format Specification <https://github.com/mapillary/OpenSfM/blob/master/doc/source/gcp.rst/>`_.
If you supply a GCP file called gcp_list.txt then ODM will automatically detect it. If it has another name you can specify using ``--gcp <path>``. If you have a gcp file and want to do georeferencing with exif instead, then you can specify ``--use-exif``.
`This post has some information about placing Ground Control Targets before a flight <http://diydrones.com/profiles/blogs/ground-control-points-gcps-for-aerial-photography>`_, but if you already have images, you can find your own points in the images post facto. It's important that you find high-contrast objects that are found in **at least** 3 photos, and that you find a minimum of 5 objects.
Sharp corners are good picks for GCPs. You should also place/find the GCPs evenly around your survey area.
The ``gcp_list.txt`` file must be created in the base of your project folder.
For good results your file should have a minimum of 15 lines after the header (5 points with 3 images to each point).
Ground Control Points Interface
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
WebODM has a GCP interface, and example of which can be seen on `the WebODM Demo <http://demo.webodm.org/plugins/posm-gcpi/>`_. To use this with known ground control XYZ values, one would do the following:
Create a GCP list that only includes gcp name (this is the label that will be seen in the GCP interface), x, y, and z, with a header with a proj4 string of your GCPs (make sure they are in a planar coordinate system, such as UTM. It should look something like this:
Since many users employ docker to deploy OpenDroneMap, it can be useful to understand some basic commands in order to interrogate the docker instances when things go wrong, or we are curious about what is happening. Docker is a containerized environment intended, among other things, to make it easier to deploy software independent of the local environment. In this way, it is similar to virtual machines.
A few simple commands can make our docker experience much better.
Listing Docker Machines
-----------------------
We can start by listing available docker machines on the current machine we are running as follows:
::
> docker ps
CONTAINER ID IMAGE COMMAND CREATED STATUS PORTS NAMES
2518817537ce opendronemap/odm "bash" 36 hours ago Up 36 hours zen_wright
1cdc7fadf688 opendronemap/nodeodm "/usr/bin/nodejs /va…" 37 hours ago Up 37 hours 0.0.0.0:3000->3000/tcp flamboyant_dhawan
If we want to see machines that may not be running but still exist, we can add the `-a` flag:
::
> docker ps -a
CONTAINER ID IMAGE COMMAND CREATED STATUS PORTS NAMES
2518817537ce opendronemap/odm "bash" 36 hours ago Up 36 hours zen_wright
1cdc7fadf688 opendronemap/nodeodm "/usr/bin/nodejs /va…" 37 hours ago Up 37 hours 0.0.0.0:3000->3000/tcp flamboyant_dhawan
cd7b9585b8f6 opendronemap/odm "bash" 3 days ago Exited (1) 37 hours ago nostalgic_lederberg
e31010c00b9a opendronemap/odm "python /code/run.py…" 3 days ago Exited (2) 3 days ago suspicious_kepler
c44e0d0b8448 opendronemap/nodeodm "/usr/bin/nodejs /va…" 3 days ago Exited (0) 37 hours ago wonderful_burnell
Accessing logs on the instance
------------------------------
Using either the `CONTAINER ID` or the name, we can access any logs available on the machine as follows:
::
> docker logs 2518817537ce
This is likely to be unwieldy large, but we can use a pipe `|` character and other tools to extract just what we need from the logs. For example we can move through the log slowly using the `more` command:
::
> docker logs 2518817537ce | more
[INFO] DTM is turned on, automatically turning on point cloud classification
Pressing `Enter` or `Space`, arrow keys or `Page Up` or `Page Down` keys will now help us navigate through the logs. The lower case letter `Q` will let us escape back to the command line.
The value `-5` tells the tail command to give us just the last 5 lines of the logs.
Command line access to instances
--------------------------------
Sometimes we need to go a little deeper in our exploration of the process for OpenDroneMap. For this, we can get direct command line access to the machines. For this, we can use `docker exec` to execute a `bash` command line shell in the machine of interest as follows:
Now we are logged into our docker instance and can explore the machine.
Cleaning up after Docker
------------------------
Docker has a lamentable use of space and by default does not clean up excess data and machines when processes are complete. This can be advantageous if we need to access a process that has since terminated, but carries the burden of using increasing amounts of storage over time. Maciej Łebkowski has an `excellent overview of how to manage excess disk usage in docker <https://lebkowski.name/docker-volumes/>`_.
