Hamlib/skanti/trp8000.c

135 wiersze
3.6 KiB
C

/*
* Hamlib Skanti backend - TRP8000 description
* Copyright (c) 2004 by Stephane Fillod
*
* $Id: trp8000.c,v 1.1 2004-08-18 18:51:24 fillods Exp $
*
* This library is free software; you can redistribute it and/or modify
* it under the terms of the GNU Library General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU Library General Public License for more details.
*
* You should have received a copy of the GNU Library General Public
* License along with this library; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
*/
#ifdef HAVE_CONFIG_H
#include "config.h"
#endif
#include <stdlib.h>
#include <hamlib/rig.h>
#include "idx_builtin.h"
#include "skanti.h"
/* modes: what about MCW, R3E ? */
#define TRP8000_ALL_MODES (RIG_MODE_AM|RIG_MODE_CW|RIG_MODE_SSB|RIG_MODE_RTTY)
#define TRP8000_OTHER_TX_MODES (RIG_MODE_CW|RIG_MODE_SSB|RIG_MODE_RTTY)
#define TRP8000_AM_TX_MODES RIG_MODE_AM
#define TRP8000_FUNC (RIG_FUNC_NONE)
#define TRP8000_LEVEL_ALL (RIG_LEVEL_RFPOWER|RIG_LEVEL_AGC|RIG_LEVEL_ATT|RIG_LEVEL_PREAMP)
#define TRP8000_PARM_ALL (RIG_PARM_NONE)
#define TRP8000_VFO (RIG_VFO_A) /* TBC */
/*
* trp8000 rig capabilities.
*
*
* TODO: TUNING, BFO, SENSITIVITY(RF gain?)
*/
const struct rig_caps trp8000_caps = {
.rig_model = RIG_MODEL_TRP8000,
.model_name = "TRP8000",
.mfg_name = "Skanti",
.version = "0.1",
.copyright = "LGPL",
.status = RIG_STATUS_UNTESTED,
.rig_type = RIG_TYPE_TRANSCEIVER,
.ptt_type = RIG_PTT_NONE,
.dcd_type = RIG_DCD_NONE,
.port_type = RIG_PORT_SERIAL,
.serial_rate_min = 300,
.serial_rate_max = 300,
.serial_data_bits = 7,
.serial_stop_bits = 1,
.serial_parity = RIG_PARITY_ODD,
.serial_handshake = RIG_HANDSHAKE_NONE,
.write_delay = 0,
.post_write_delay = 0,
.timeout = 2000,
.retry = 3,
.has_get_func = TRP8000_FUNC,
.has_set_func = TRP8000_FUNC,
.has_get_level = RIG_LEVEL_NONE,
.has_set_level = RIG_LEVEL_SET(TRP8000_LEVEL_ALL),
.has_get_parm = RIG_PARM_NONE,
.has_set_parm = RIG_PARM_SET(TRP8000_PARM_ALL),
.vfo_ops = RIG_OP_TUNE,
.preamp = { 10, RIG_DBLST_END }, /* TBC */
.attenuator = { 20, RIG_DBLST_END }, /* TBC */
.max_rit = Hz(0),
.max_xit = Hz(0),
.max_ifshift = Hz(0),
.targetable_vfo = 0,
.transceive = RIG_TRN_OFF,
.bank_qty = 0,
.chan_desc_sz = 0,
.chan_list = { RIG_CHAN_END, },
.rx_range_list1 = { RIG_FRNG_END, }, /* FIXME: enter region 1 setting */
.tx_range_list1 = { RIG_FRNG_END, },
.rx_range_list2 = {
{kHz(500),MHz(30),TRP8000_ALL_MODES,-1,-1,TRP8000_VFO},
RIG_FRNG_END,
},
.tx_range_list2 = {
{MHz(2),MHz(30),TRP8000_AM_TX_MODES,W(4),W(40),TRP8000_VFO},
{MHz(2),MHz(30),TRP8000_OTHER_TX_MODES,W(10),W(100),TRP8000_VFO},
RIG_FRNG_END,
},
.tuning_steps = {
{TRP8000_ALL_MODES,100},
{TRP8000_ALL_MODES,10},
{TRP8000_ALL_MODES,kHz(1)},
RIG_TS_END,
},
/* mode/filter list, remember: order matters! */
.filters = {
/* rough guesses */
{TRP8000_ALL_MODES, kHz(2.7)}, /* intermit */
{TRP8000_ALL_MODES, kHz(2.1)}, /* narrow */
{TRP8000_ALL_MODES, kHz(6)}, /* wide */
{TRP8000_ALL_MODES, Hz(500)}, /* very narrow */
RIG_FLT_END,
},
.set_freq = skanti_set_freq,
.set_mode = skanti_set_mode,
.set_split_freq = skanti_set_split_freq,
.set_ptt = skanti_set_ptt,
.vfo_op = skanti_vfo_op,
.set_level = skanti_set_level,
.reset = skanti_reset,
};
/*
* Function definitions below
*/