Hamlib/skanti/trp8000.c

/*
 *  Hamlib Skanti backend - TRP8000 description
 *  Copyright (c) 2004 by Stephane Fillod
 *
 *	$Id: trp8000.c,v 1.1 2004-08-18 18:51:24 fillods Exp $
 *
 *   This library is free software; you can redistribute it and/or modify
 *   it under the terms of the GNU Library General Public License as
 *   published by the Free Software Foundation; either version 2 of
 *   the License, or (at your option) any later version.
 *
 *   This program is distributed in the hope that it will be useful,
 *   but WITHOUT ANY WARRANTY; without even the implied warranty of
 *   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 *   GNU Library General Public License for more details.
 *
 *   You should have received a copy of the GNU Library General Public
 *   License along with this library; if not, write to the Free Software
 *   Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
 *
 */

#ifdef HAVE_CONFIG_H
#include "config.h"
#endif

#include <stdlib.h>

#include <hamlib/rig.h>
#include "idx_builtin.h"
#include "skanti.h"


/* modes: what about MCW, R3E ? */
#define TRP8000_ALL_MODES (RIG_MODE_AM|RIG_MODE_CW|RIG_MODE_SSB|RIG_MODE_RTTY)
#define TRP8000_OTHER_TX_MODES (RIG_MODE_CW|RIG_MODE_SSB|RIG_MODE_RTTY)
#define TRP8000_AM_TX_MODES RIG_MODE_AM

#define TRP8000_FUNC (RIG_FUNC_NONE)

#define TRP8000_LEVEL_ALL (RIG_LEVEL_RFPOWER|RIG_LEVEL_AGC|RIG_LEVEL_ATT|RIG_LEVEL_PREAMP)

#define TRP8000_PARM_ALL (RIG_PARM_NONE)

#define TRP8000_VFO (RIG_VFO_A)	/* TBC */

/*
 * trp8000 rig capabilities.
 *
 *
 * TODO: TUNING, BFO, SENSITIVITY(RF gain?)
 */
const struct rig_caps trp8000_caps = {
.rig_model =  RIG_MODEL_TRP8000,
.model_name = "TRP8000",
.mfg_name =  "Skanti",
.version =  "0.1",
.copyright =  "LGPL",
.status =  RIG_STATUS_UNTESTED,
.rig_type =  RIG_TYPE_TRANSCEIVER,
.ptt_type =  RIG_PTT_NONE,
.dcd_type =  RIG_DCD_NONE,
.port_type =  RIG_PORT_SERIAL,
.serial_rate_min =  300,
.serial_rate_max =  300,
.serial_data_bits =  7,
.serial_stop_bits =  1,
.serial_parity =  RIG_PARITY_ODD,
.serial_handshake =  RIG_HANDSHAKE_NONE,
.write_delay =  0,
.post_write_delay =  0,
.timeout =  2000,
.retry =  3,

.has_get_func =  TRP8000_FUNC,
.has_set_func =  TRP8000_FUNC,
.has_get_level =  RIG_LEVEL_NONE,
.has_set_level =  RIG_LEVEL_SET(TRP8000_LEVEL_ALL),
.has_get_parm =  RIG_PARM_NONE,
.has_set_parm =  RIG_PARM_SET(TRP8000_PARM_ALL),
.vfo_ops =  RIG_OP_TUNE,
.preamp =   { 10, RIG_DBLST_END },	/* TBC */
.attenuator =   { 20, RIG_DBLST_END },	/* TBC */
.max_rit =  Hz(0),
.max_xit =  Hz(0),
.max_ifshift =  Hz(0),
.targetable_vfo =  0,
.transceive =  RIG_TRN_OFF,
.bank_qty =   0,
.chan_desc_sz =  0,

.chan_list =  { RIG_CHAN_END, },

.rx_range_list1 =  { RIG_FRNG_END, },    /* FIXME: enter region 1 setting */
.tx_range_list1 =  { RIG_FRNG_END, },
.rx_range_list2 =  {
	{kHz(500),MHz(30),TRP8000_ALL_MODES,-1,-1,TRP8000_VFO},
	RIG_FRNG_END,
  },
.tx_range_list2 =  {
	{MHz(2),MHz(30),TRP8000_AM_TX_MODES,W(4),W(40),TRP8000_VFO},
	{MHz(2),MHz(30),TRP8000_OTHER_TX_MODES,W(10),W(100),TRP8000_VFO},
	RIG_FRNG_END,
  },
.tuning_steps =  {
	 {TRP8000_ALL_MODES,100},
	 {TRP8000_ALL_MODES,10},
	 {TRP8000_ALL_MODES,kHz(1)},
	 RIG_TS_END,
	},
        /* mode/filter list, remember: order matters! */
.filters =  {
		/* rough guesses */
		{TRP8000_ALL_MODES, kHz(2.7)},	/* intermit */
		{TRP8000_ALL_MODES, kHz(2.1)},	/* narrow */
		{TRP8000_ALL_MODES, kHz(6)},	/* wide */
		{TRP8000_ALL_MODES, Hz(500)},	/* very narrow */
		RIG_FLT_END,
	},

.set_freq =  skanti_set_freq,
.set_mode =  skanti_set_mode,
.set_split_freq =  skanti_set_split_freq,
.set_ptt =  skanti_set_ptt,
.vfo_op =  skanti_vfo_op,
.set_level =  skanti_set_level,
.reset =  skanti_reset,

};

/*
 * Function definitions below
 */