Wykres commitów

7599 Commity (623bef2f61a6624f02bf9ff8dcb15c0e1f275d19)

Autor SHA1 Wiadomość Data
Mike Black W9MDB 623bef2f61 Move Startup debug line after set_debug_level 2021-09-04 22:13:32 +02:00
Mike Black W9MDB 32460321ab astyle files 2021-09-04 22:13:32 +02:00
kacomet fa4fa7a1d9 Corrected modes for FT-736R. The FT-736 supports SSB, CW, FM, FM-N (narrowband FM,) CW-N (narrowband CW.) Now, the FM-N and CW-N modes can be set from rigctl. Passbands have also been corrected to the values in the manual. 2021-09-04 22:13:32 +02:00
Mike Black W9MDB 124e2c30c7 Remove RX from kenwood.c -- did not put rig on VFOA
https://github.com/Hamlib/Hamlib/issues/746
2021-09-04 22:13:32 +02:00
Mike Black W9MDB c04c4cbd2a Remove another unneeded vfo swap from icom rigs
https://github.com/Hamlib/Hamlib/issues/762
https://github.com/Hamlib/Hamlib/issues/430
2021-09-04 22:13:32 +02:00
Mike Black W9MDB 83590a0868 Fix uninitialized warning in rig.c
https://github.com/Hamlib/Hamlib/issues/762
    https://github.com/Hamlib/Hamlib/issues/430
2021-09-04 22:13:32 +02:00
Mike Black W9MDB d5028e7ba4 Fix some more unnecessary vfo swapping
https://github.com/Hamlib/Hamlib/issues/762
https://github.com/Hamlib/Hamlib/issues/430
2021-09-04 22:13:32 +02:00
Mike Black W9MDB 31696351a9 Add RX command to kenwood rigs hopefully setting VFO to VFOA after split set
FT450 and others turn split off doing FR0 and FT1; leaves the rig on VFOB
https://github.com/Hamlib/Hamlib/issues/746
2021-09-04 22:13:32 +02:00
Mike Black W9MDB fcdacb2540 Finish up targetable_ptt logic
Was causing unnecessary vfo swapping
https://github.com/Hamlib/Hamlib/issues/762
https://github.com/Hamlib/Hamlib/issues/430
2021-09-04 22:13:32 +02:00
Mike Black W9MDB 3dde32f534 Move TARGETABLE_PTT logic to the set_ptt routine
https://github.com/Hamlib/Hamlib/issues/762
https://github.com/Hamlib/Hamlib/issues/430
2021-09-04 22:13:32 +02:00
Mike Black W9MDB 6a9432a0c7 Fix possilbe segfault last patch
https://github.com/Hamlib/Hamlib/issues/762
https://github.com/Hamlib/Hamlib/issues/430
2021-09-04 22:13:32 +02:00
Mike Black W9MDB 1c7b4ab806 Allow all Icom, Kenwood, Yaesu to avoid VFO swapping
https://github.com/Hamlib/Hamlib/issues/762
https://github.com/Hamlib/Hamlib/issues/430
2021-09-04 22:13:32 +02:00
Mike Black W9MDB eecffd31be Change kenwood set_split to check split instead of priv->split
https://github.com/Hamlib/Hamlib/issues/746
2021-09-04 22:13:32 +02:00
Mike Black W9MDB a851da80e2 Fix Kenwood FR/FT sequencing
https://github.com/Hamlib/Hamlib/issues/746
2021-09-04 22:13:32 +02:00
Mike Black W9MDB aedcc4191c Fix typo in scripts/Makefile.am 2021-09-04 22:13:32 +02:00
Mike Black W9MDB 9b650f9dc5 Add build script for jtsdk to Makefile.am 2021-09-04 22:13:32 +02:00
Mike Black W9MDB 9c44e29ec6 Add ax_cxx_compile_stdcxx.m4 to macros/Makefile.am 2021-09-04 22:13:32 +02:00
Mike Black W9MDB c823564a2a astyle all files preparing for 4.3 release 2021-09-04 22:13:32 +02:00
Mike Black W9MDB 49c7e09142 Put simulators in their own directory...this is an ongoing project to make these more robust.
Simulators are currently used to debug things and need to improved to allow model selection and all the complexities of simulating multiple models
2021-09-04 22:13:32 +02:00
Wouter van Gulik 49240c9846 Simplify get_ant by having setting to unknown by default.
Drop setting to default in rigs.
Add some more documentation on get_ant.
2021-09-04 22:13:32 +02:00
Mike Black W9MDB 5a2cbdda21 Fix lack of error for some bad rig numbers. e.g. rigctl -m 228 produced hash collision error instead of unknown rig
https://github.com/Hamlib/Hamlib/issues/735
2021-09-04 22:13:32 +02:00
Mike Black W9MDB dd6224bc5b Fix Kenwood rigs that turn split off during FR command by turning split back on if needed
https://github.com/Hamlib/Hamlib/issues/746
2021-09-04 22:13:32 +02:00
Mike Black W9MDB 19c5e3e0a7 Fix ANT get/set for IC756Pro series
https://github.com/Hamlib/Hamlib/issues/774
2021-09-04 22:13:32 +02:00
Mike Black W9MDB 82b0a8a84e Improve debug in ser_open 2021-09-04 22:13:32 +02:00
Mike Black W9MDB 2fb5343cc1 Add more retries to PTT serial port open
https://github.com/Hamlib/Hamlib/issues/768
2021-09-04 22:13:32 +02:00
Wouter van Gulik 617a38ff45 src/misc.c: Constify some tables 2021-09-04 22:13:32 +02:00
Wouter van Gulik c9860abe9f rig.c: Constify rigerror_table 2021-09-04 22:13:32 +02:00
Wouter van Gulik f85cb7cb80 src/rig.c: Add comments to clarify both mode and width must be supplied 2021-09-04 22:13:32 +02:00
Wouter van Gulik a305b4f205 ft600.c: Drop width check, code below has no check.
The lower code would have crashed if width was NULL, so 'width == NULL' never
happens.
2021-09-04 22:13:32 +02:00
Wouter van Gulik bfd0820362 icom.c: Drop width check. Other code assumes != NULL.
I am not sure if the intention was to check for width == default.
But that never worked, so for now do not change behaviour.
2021-09-04 22:13:32 +02:00
Wouter van Gulik 447fda0681 newcat.c: Drop width check; the only call site (get_mode) uses it before the call.
Besides most other rigs assume it is != NULL. So having width == NULL
would cause a crash for all other rigs.
2021-09-04 22:13:32 +02:00
Mike Black W9MDB 4c371ca40a Fix typo in serial.c
https://github.com/Hamlib/Hamlib/issues/768
2021-09-04 22:13:32 +02:00
Mike Black W9MDB 9311519461 Fix error in serial.c
https://github.com/Hamlib/Hamlib/issues/768
2021-09-04 22:13:32 +02:00
Mike Black W9MDB 18bbd6b7a7 Add additional attempts to open serial port
K4 was failing on 1st open for some unknown reason but succeeds on 2nd try
https://github.com/Hamlib/Hamlib/issues/768
2021-09-04 22:13:32 +02:00
Mike Black W9MDB 61020e950c Allow testlibusb to compile on < libusb-1.0.23
Generate warning for libusb-1.0.23 future requirement
https://github.com/Hamlib/Hamlib/issues/763
2021-09-04 22:13:31 +02:00
Mike Black W9MDB d97eba3c70 Update NEWS 2021-09-04 22:13:31 +02:00
Mike Black W9MDB 012b939a19 Fix without-libusb build to not build testlibusb 2021-09-04 22:13:31 +02:00
Mike Black W9MDB 5ece51ef2f Remove priv statement 2021-09-04 22:13:31 +02:00
Wouter van Gulik 78160a1bf6 FT817/FT818 Drop pcs and use ncmd direct 2021-09-04 22:13:31 +02:00
Wouter van Gulik 9849a1bcaf Implement get_vfo/set_vfo for FT817/FT818.
Read the eeprom to get VFO and toggle VFO if not the desired VFO is selected.
This code is the ft857 implementation, but EEPROM address 0x55 instead of 0x68.
2021-09-04 22:13:31 +02:00
Wouter van Gulik cb9ea39c66 Move private data structs of ft100, ft600, ft817, ft857, ft897 to the C file.
Note that is already so for all other Yaesu device.
Leave private data in newcat; it is used by multiple rigs.
2021-09-04 22:13:31 +02:00
Wouter 3fabc0b503 README: current version is 4 2021-09-04 22:13:31 +02:00
Mike Black W9MDB b2560982fe Add LIBUSB flags to hamlib.m4
https://github.com/Hamlib/Hamlib/issues/763
2021-09-04 22:13:31 +02:00
Mike Black W9MDB 36b4233277 Change tests/Makefile.am testlibusb to use LIBUSB_CFLAGS and LIBUSB_LIBS 2021-09-04 22:13:31 +02:00
Mike Black W9MDB 181571a970 Add fallback serial open logic to hopefully cure serial port open error with K4
https://github.com/Hamlib/Hamlib/issues/768
2021-09-04 22:13:31 +02:00
Mike Black W9MDB 724891246a Remove csharp from codeql-analysis 2021-09-04 22:13:31 +02:00
Mike Black W9MDB 908b18246e Hopefully portable detection of libusb.h in testlibusb.c
https://github.com/Hamlib/Hamlib/issues/763
2021-09-04 22:13:31 +02:00
Mike Black W9MDB 356f23b0fb Fixing codesql-analysis.yml 2021-09-04 22:13:31 +02:00
Mike Black W9MDB 67181bf7c9 Fixing codesql-analysis.yml 2021-09-04 22:13:31 +02:00
Mike Black W9MDB 6cb90f5260 Fixing c-cpp.yml for libusb 2021-09-04 22:13:31 +02:00