sforkowany z mirror/meshtastic-firmware
106 wiersze
3.5 KiB
C++
106 wiersze
3.5 KiB
C++
/*
|
|
Copyright (c) 2014-2015 Arduino LLC. All right reserved.
|
|
Copyright (c) 2016 Sandeep Mistry All right reserved.
|
|
Copyright (c) 2018, Adafruit Industries (adafruit.com)
|
|
|
|
This library is free software; you can redistribute it and/or
|
|
modify it under the terms of the GNU Lesser General Public
|
|
License as published by the Free Software Foundation; either
|
|
version 2.1 of the License, or (at your option) any later version.
|
|
|
|
This library is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
|
See the GNU Lesser General Public License for more details.
|
|
|
|
You should have received a copy of the GNU Lesser General Public
|
|
License along with this library; if not, write to the Free Software
|
|
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
|
|
*/
|
|
|
|
#include "variant.h"
|
|
#include "nrf.h"
|
|
#include "wiring_constants.h"
|
|
#include "wiring_digital.h"
|
|
|
|
const uint32_t g_ADigitalPinMap[] = {
|
|
// D0 .. D13
|
|
25, // D0 is P0.25 (UART TX)
|
|
24, // D1 is P0.24 (UART RX
|
|
10, // D2 is P0.10 (NFC2)
|
|
47, // D3 is P1.15 (LED1)
|
|
(32 + 10), // D4 is P1.10 (LED2)
|
|
40, // D5 is P1.08
|
|
7, // D6 is P0.07
|
|
34, // D7 is P1.02 (Switch)
|
|
16, // D8 is P0.16 (NeoPixel)
|
|
26, // D9 is P0.26 D_RS (IPS data/command control)
|
|
27, // D10 is P0.27
|
|
6, // D11 is P0.06 D_RES (IPS display reset)
|
|
8, // D12 is P0.08 D_CS (IPS display chip select)
|
|
41, // D13 is P0.23 BLT (IPS display backlight)
|
|
4, // D14 is P0.04 SX1262 RXEN
|
|
5, // D15 is P0.05 BOOST_EN (5V buck converter enable for the the radio power)
|
|
|
|
// D14 .. D21 (aka A0 .. A7)
|
|
30, // D16 is P0.30 (A0)
|
|
28, // D17 is P0.28 (A1)
|
|
2, // D18 is P0.02 (A2)
|
|
3, // D19 is P0.03 (A3)
|
|
29, // D20 is P0.29 (A4, Battery)
|
|
31, // D21 is P0.31 (A5, ARef)
|
|
|
|
// D22 .. D23 (aka I2C pins)
|
|
12, // D22 is P0.12 (SDA)
|
|
11, // D23 is P0.11 (SCL)
|
|
|
|
// D24 .. D26 (aka SPI pins)
|
|
15, // D24 is P0.15 (SPI MISO)
|
|
13, // D25 is P0.13 (SPI MOSI)
|
|
14, // D26 is P0.14 (SPI SCK )
|
|
|
|
// QSPI pins (not exposed via any header / test point)
|
|
// 19, // P0.19 (QSPI CLK)
|
|
// 20, // P0.20 (QSPI CS)
|
|
// 17, // P0.17 (QSPI Data 0)
|
|
// 22, // P0.22 (QSPI Data 1)
|
|
// 23, // P0.23 (QSPI Data 2)
|
|
// 21, // P0.21 (QSPI Data 3)
|
|
|
|
// The remaining NFC pin
|
|
9, // D27 P0.09 (NFC1, exposed only via test point on bottom of board)
|
|
|
|
// The following pins were never listed as they were considered unusable
|
|
// 0, // P0.00 is XL1 (attached to 32.768kHz crystal) Never expose as GPIOs
|
|
// 1, // P0.01 is XL2 (attached to 32.768kHz crystal)
|
|
18, // D28 P0.18 is RESET (attached to switch)
|
|
// 32, // P1.00 is SWO (attached to debug header)
|
|
|
|
// D29-D43
|
|
32 + 12, // D29 P0.27 E22-SX1262 DIO1
|
|
28, // D30 P0.28 E22-SX1262 DIO2
|
|
30, // D31 P0.30 E22-SX1262 TXEN
|
|
35, // D32 P1.03 E22-SX1262 NSS
|
|
32 + 8, // D33 P1.08 E22-SX1262 BUSY
|
|
27, // D34 P0.27 E22-SX1262 RESET
|
|
32 + 1, // D35 P1.01 BTN_UP
|
|
32, // D36 P1.0 GPS power
|
|
21, // D37 P0.21 disp_clk
|
|
36, // P1.04 BTN_OK
|
|
37, // D39 P0.19 disp_SDA
|
|
38, // D40 P1.06 BUZZER
|
|
39, // P1.07 is not connected per schematic
|
|
43, // P1.11 is not connected per schematic
|
|
45, // P1.13 is not connected per schematic
|
|
};
|
|
|
|
void initVariant()
|
|
{
|
|
// LED1 & LED2
|
|
pinMode(PIN_LED1, OUTPUT);
|
|
ledOff(PIN_LED1);
|
|
|
|
pinMode(PIN_LED2, OUTPUT);
|
|
ledOff(PIN_LED2);
|
|
}
|