sforkowany z mirror/meshtastic-firmware
253 wiersze
7.9 KiB
C
253 wiersze
7.9 KiB
C
/*
|
|
Copyright (c) 2014-2015 Arduino LLC. All right reserved.
|
|
Copyright (c) 2016 Sandeep Mistry All right reserved.
|
|
Copyright (c) 2018, Adafruit Industries (adafruit.com)
|
|
|
|
This library is free software; you can redistribute it and/or
|
|
modify it under the terms of the GNU Lesser General Public
|
|
License as published by the Free Software Foundation; either
|
|
version 2.1 of the License, or (at your option) any later version.
|
|
This library is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
|
See the GNU Lesser General Public License for more details.
|
|
You should have received a copy of the GNU Lesser General Public
|
|
License along with this library; if not, write to the Free Software
|
|
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
|
|
*/
|
|
|
|
#ifndef _VARIANT_TTGO_EINK_V1_
|
|
#define _VARIANT_TTGO_EINK_V1_
|
|
|
|
/** Master clock frequency */
|
|
#define VARIANT_MCK (64000000ul)
|
|
|
|
#define USE_LFXO // Board uses 32khz crystal for LF
|
|
|
|
/*
|
|
@geeksville eink TODO:
|
|
|
|
soonish:
|
|
DONE hook cdc acm device to debug output
|
|
DONE fix bootloader to use two buttons - remove bootloader hacks
|
|
DONE get second button working in app load
|
|
DONE use tp_ser_io as a button, it goes high when pressed unify eink display classes
|
|
fix display width and height
|
|
clean up eink drawing to not have the nasty timeout hack
|
|
measure current draws
|
|
DONE put eink to sleep when we think the screen is off
|
|
enable gps sleep mode
|
|
turn off txco on lora?
|
|
make screen.adjustBrightness() a nop on eink screens
|
|
|
|
later:
|
|
enable flash on qspi.
|
|
fix floating point SEGGER printf on nrf52 - see "new NMEA GPS pos"
|
|
add factory/power on self test
|
|
|
|
feedback to give:
|
|
|
|
* bootloader is finished
|
|
|
|
* the capacitive touch sensor works, though I'm not sure what use you are intending for it
|
|
|
|
* remove ipx connector for nfc, instead use two caps and loop traces on the back of the board as an antenna?
|
|
|
|
* the i2c RTC seems to talk fine on the i2c bus. However, I'm not sure of the utility of that part. Instead I'd be in favor of
|
|
the following:
|
|
|
|
* move BAT1 to power the GPS VBACKUP instead per page 6 of the Air530 datasheet. And remove the i2c RTC entirely.
|
|
|
|
* remove the cp2014 chip.
|
|
|
|
* I've made the serial flash chip work, but if you do a new spin of the board I recommend:
|
|
connect pin 3 and pin 7 of U4 to spare GPIOs on the processor (instead of their current connections),
|
|
This would allow using 4 bit wide interface mode to the serial flash - doubling the transfer speed! see example here:
|
|
https://infocenter.nordicsemi.com/topic/ug_nrf52840_dk/UG/nrf52840_DK/hw_external_memory.html?cp=4_0_4_7_4
|
|
Once again - I'm glad you added that external flash chip.
|
|
|
|
* Power measurements
|
|
When powered by 4V battery
|
|
|
|
CPU on, lora radio RX mode, bluetooth enabled, GPS trying to lock. total draw 43mA
|
|
CPU on, lora radio RX mode, bluetooth enabled, GPS super low power sleep mode. Total draw 20mA
|
|
CPU on, lora radio TX mode, bluetooth enabled, GPS super low power sleep mode. Total draw 132mA
|
|
|
|
Note: power consumption while connected via BLE to a phone almost identical.
|
|
|
|
Note: eink display for all tests was in sleep mode most of the time. Current draw during the brief periods while the eink was being drawn was not
|
|
measured (but it was low).
|
|
|
|
Note: Turning off EINK PWR_ON produces no noticeable power savings over just putting the eink display into sleep mode.
|
|
|
|
*/
|
|
|
|
/*----------------------------------------------------------------------------
|
|
* Headers
|
|
*----------------------------------------------------------------------------*/
|
|
|
|
#include "WVariant.h"
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif // __cplusplus
|
|
|
|
// Number of pins defined in PinDescription array
|
|
#define PINS_COUNT (48)
|
|
#define NUM_DIGITAL_PINS (48)
|
|
#define NUM_ANALOG_INPUTS (1)
|
|
#define NUM_ANALOG_OUTPUTS (0)
|
|
|
|
// LEDs
|
|
#define PIN_LED1 (0 + 13) // green (but red on my prototype)
|
|
#define PIN_LED2 (0 + 15) // blue (but red on my prototype)
|
|
#define PIN_LED3 (0 + 14) // red (not functional on my prototype)
|
|
|
|
#define LED_RED PIN_LED3
|
|
#define LED_GREEN PIN_LED1
|
|
#define LED_BLUE PIN_LED2
|
|
|
|
#define LED_BUILTIN LED_GREEN
|
|
#define LED_CONN PIN_BLUE
|
|
|
|
#define LED_STATE_ON 0 // State when LED is lit
|
|
#define LED_INVERTED 1
|
|
|
|
/*
|
|
* Buttons
|
|
*/
|
|
#define PIN_BUTTON1 (32 + 10)
|
|
#define PIN_BUTTON2 (0 + 18) // 0.18 is labeled on the board as RESET but we configure it in the bootloader as a regular GPIO
|
|
|
|
/*
|
|
* Analog pins
|
|
*/
|
|
#define PIN_A0 (4) // Battery ADC
|
|
|
|
#define BATTERY_PIN PIN_A0
|
|
|
|
static const uint8_t A0 = PIN_A0;
|
|
|
|
#define ADC_RESOLUTION 14
|
|
|
|
#define PIN_NFC1 (9)
|
|
#define PIN_NFC2 (10)
|
|
|
|
/*
|
|
* Serial interfaces
|
|
*/
|
|
|
|
/*
|
|
No longer populated on PCB
|
|
*/
|
|
//#define PIN_SERIAL2_RX (0 + 6)
|
|
//#define PIN_SERIAL2_TX (0 + 8)
|
|
// #define PIN_SERIAL2_EN (0 + 17)
|
|
|
|
/**
|
|
Wire Interfaces
|
|
*/
|
|
#define WIRE_INTERFACES_COUNT 1
|
|
|
|
#define PIN_WIRE_SDA (26) // Not connected on board?
|
|
#define PIN_WIRE_SCL (27)
|
|
|
|
/* touch sensor, active high */
|
|
|
|
#define TP_SER_IO (0 + 11)
|
|
|
|
#define PIN_RTC_INT (0 + 16) // Interrupt from the PCF8563 RTC
|
|
|
|
/*
|
|
External serial flash WP25R1635FZUIL0
|
|
*/
|
|
|
|
// QSPI Pins
|
|
#define PIN_QSPI_SCK (32 + 14)
|
|
#define PIN_QSPI_CS (32 + 15)
|
|
#define PIN_QSPI_IO0 (32 + 12) // MOSI if using two bit interface
|
|
#define PIN_QSPI_IO1 (32 + 13) // MISO if using two bit interface
|
|
//#define PIN_QSPI_IO2 22 // WP if using two bit interface (i.e. not used)
|
|
//#define PIN_QSPI_IO3 23 // HOLD if using two bit interface (i.e. not used)
|
|
|
|
// On-board QSPI Flash
|
|
#define EXTERNAL_FLASH_DEVICES MX25R1635F
|
|
#define EXTERNAL_FLASH_USE_QSPI
|
|
|
|
/*
|
|
* Lora radio
|
|
*/
|
|
|
|
#define SX1262_CS (0 + 24) // FIXME - we really should define LORA_CS instead
|
|
#define SX1262_DIO1 (0 + 20)
|
|
// Note DIO2 is attached internally to the module to an analog switch for TX/RX switching
|
|
#define SX1262_DIO3 \
|
|
(0 + 21) // This is used as an *output* from the sx1262 and connected internally to power the tcxo, do not drive from the main
|
|
// CPU?
|
|
#define SX1262_BUSY (0 + 17)
|
|
#define SX1262_RESET (0 + 25)
|
|
#define SX1262_E22 // Not really an E22 but TTGO seems to be trying to clone that
|
|
// Internally the TTGO module hooks the SX1262-DIO2 in to control the TX/RX switch (which is the default for the sx1262interface
|
|
// code)
|
|
|
|
// #define LORA_DISABLE_SENDING // Define this to disable transmission for testing (power testing etc...)
|
|
|
|
/*
|
|
* eink display pins
|
|
*/
|
|
|
|
#define PIN_EINK_EN (32 + 11)
|
|
#define PIN_EINK_CS (0 + 30)
|
|
#define PIN_EINK_BUSY (0 + 3)
|
|
#define PIN_EINK_DC (0 + 28)
|
|
#define PIN_EINK_RES (0 + 2)
|
|
#define PIN_EINK_SCLK (0 + 31)
|
|
#define PIN_EINK_MOSI (0 + 29) // also called SDI
|
|
|
|
// Controls power for the eink display - Board power is enabled either by VBUS from USB or the CPU asserting PWR_ON
|
|
#define PIN_EINK_PWR_ON (0 + 12)
|
|
|
|
#define HAS_EINK
|
|
|
|
#define PIN_SPI1_MISO \
|
|
(32 + 7) // FIXME not really needed, but for now the SPI code requires something to be defined, pick an used GPIO
|
|
#define PIN_SPI1_MOSI PIN_EINK_MOSI
|
|
#define PIN_SPI1_SCK PIN_EINK_SCLK
|
|
|
|
/*
|
|
* Air530 GPS pins
|
|
*/
|
|
|
|
#define PIN_GPS_WAKE (32 + 2) // An output to wake GPS, low means allow sleep, high means force wake
|
|
#define PIN_GPS_PPS (32 + 4) // Pulse per second input from the GPS
|
|
#define PIN_GPS_TX (32 + 9) // This is for bits going TOWARDS the CPU
|
|
#define PIN_GPS_RX (32 + 8) // This is for bits going TOWARDS the GPS
|
|
|
|
#define HAS_AIR530_GPS
|
|
|
|
#define PIN_SERIAL1_RX PIN_GPS_TX
|
|
#define PIN_SERIAL1_TX PIN_GPS_RX
|
|
|
|
/*
|
|
* SPI Interfaces
|
|
*/
|
|
#define SPI_INTERFACES_COUNT 2
|
|
|
|
// For LORA, spi 0
|
|
#define PIN_SPI_MISO (0 + 23)
|
|
#define PIN_SPI_MOSI (0 + 22)
|
|
#define PIN_SPI_SCK (0 + 19)
|
|
|
|
// To debug via the segger JLINK console rather than the CDC-ACM serial device
|
|
#define USE_SEGGER
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
|
|
/*----------------------------------------------------------------------------
|
|
* Arduino objects - C++ only
|
|
*----------------------------------------------------------------------------*/
|
|
|
|
#endif
|