meshtastic-firmware/variants/lora_relay_v1/variant.h

153 wiersze
4.2 KiB
C

/*
Copyright (c) 2014-2015 Arduino LLC. All right reserved.
Copyright (c) 2016 Sandeep Mistry All right reserved.
Copyright (c) 2018, Adafruit Industries (adafruit.com)
This library is free software; you can redistribute it and/or
modify it under the terms of the GNU Lesser General Public
License as published by the Free Software Foundation; either
version 2.1 of the License, or (at your option) any later version.
This library is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
See the GNU Lesser General Public License for more details.
You should have received a copy of the GNU Lesser General Public
License along with this library; if not, write to the Free Software
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#ifndef _VARIANT_LORA_RELAY_V1_
#define _VARIANT_LORA_RELAY_V1_
/** Master clock frequency */
#define VARIANT_MCK (64000000ul)
#define USE_LFXO // Board uses 32khz crystal for LF
// define USE_LFRC // Board uses RC for LF
/*----------------------------------------------------------------------------
* Headers
*----------------------------------------------------------------------------*/
#include "WVariant.h"
#ifdef __cplusplus
extern "C" {
#endif // __cplusplus
// Number of pins defined in PinDescription array
#define PINS_COUNT (43)
#define NUM_DIGITAL_PINS (43)
#define NUM_ANALOG_INPUTS (6) // A6 is used for battery, A7 is analog reference
#define NUM_ANALOG_OUTPUTS (0)
// LEDs
#define PIN_LED1 (3)
#define PIN_LED2 (4)
#define PIN_NEOPIXEL (8)
#define LED_BUILTIN PIN_LED1
#define LED_CONN PIN_LED2
#define LED_RED PIN_LED1
#define LED_BLUE PIN_LED2
#define LED_STATE_ON 1 // State when LED is litted
/*
* Buttons
*/
#define PIN_BUTTON1 (7)
/*
* Analog pins
*/
#define PIN_A0 (16)
#define PIN_A1 (17)
#define PIN_A2 (18)
#define PIN_A3 (19)
#define PIN_A4 (20)
#define PIN_A5 (21)
static const uint8_t A0 = PIN_A0;
static const uint8_t A1 = PIN_A1;
static const uint8_t A2 = PIN_A2;
static const uint8_t A3 = PIN_A3;
static const uint8_t A4 = PIN_A4;
static const uint8_t A5 = PIN_A5;
#define ADC_RESOLUTION 14
// Other pins
#define PIN_AREF PIN_A5
#define PIN_VBAT PIN_A4
#define PIN_NFC1 (33)
#define PIN_NFC2 (2)
#define PIN_PIEZO (37)
static const uint8_t AREF = PIN_AREF;
/*
* Serial interfaces
*/
#define PIN_SERIAL1_RX (1)
#define PIN_SERIAL1_TX (0)
/*
* SPI Interfaces
*/
#define SPI_INTERFACES_COUNT 1
#define PIN_SPI_MISO (24)
#define PIN_SPI_MOSI (25)
#define PIN_SPI_SCK (26)
static const uint8_t SS = (5);
static const uint8_t MOSI = PIN_SPI_MOSI;
static const uint8_t MISO = PIN_SPI_MISO;
static const uint8_t SCK = PIN_SPI_SCK;
/*
* Wire Interfaces
*/
#define WIRE_INTERFACES_COUNT 1
#define PIN_WIRE_SDA (22)
#define PIN_WIRE_SCL (23)
// I2C device addresses
#define I2C_ADDR_BQ27441 0x55 // Battery gauge
// CUSTOM GPIOs the SX1262
#define SX1262_CS (32)
// If you would prefer to get console debug output over the JTAG ICE connection rather than the CDC-ACM USB serial device, just
// define this. #define USE_SEGGER
#define SX1262_DIO1 (29)
#define SX1262_DIO2 (30)
#define SX1262_BUSY (33) // Supposed to be P0.18 but because of reworks, now on P0.31 (18)
#define SX1262_RESET (34)
// #define SX1262_ANT_SW (32 + 10)
#define SX1262_RXEN (14)
#define SX1262_TXEN (31)
#define SX1262_POWER_EN \
(15) // FIXME, see warning hre https://github.com/BigCorvus/SX1262-LoRa-BLE-Relay/blob/master/LORA_RELAY_NRF52840.ino
#define SX1262_E22 // Indicates this SX1262 is inside of an ebyte E22 module and special config should be done for that
#define ST7735_RESET (11) // Output
#define ST7735_CS (12)
#define ST7735_BACKLIGHT_EN (13)
#define ST7735_RS (9)
// #define LORA_DISABLE_SENDING // The board can brownout during lora TX if you don't have a battery connected. Disable sending
// to allow USB power only based debugging
#ifdef __cplusplus
}
#endif
/*----------------------------------------------------------------------------
* Arduino objects - C++ only
*----------------------------------------------------------------------------*/
#endif