'station-g1'

src/esp32/architecture.h

@@ -70,6 +70,8 @@
     #define HW_VENDOR HardwareModel_NANO_G1
 #elif defined(M5STACK)
     #define HW_VENDOR HardwareModel_M5STACK
+#elif defined(STATION_G1)
+    #define HW_VENDOR HardwareModel_STATION_G1
 #endif
 
 //

src/mesh/generated/mesh.pb.h

@@ -71,6 +71,8 @@ typedef enum _HardwareModel {
     HardwareModel_DR_DEV = 43, 
     /* M5 esp32 based MCU modules with enclosure, TFT and LORA Shields. All Variants (Basic, Core, Fire, Core2, Paper) https://m5stack.com/ */
     HardwareModel_M5STACK = 44,
+    /* B&Q Consulting Station Edition G1: https://uniteng.com/wiki/doku.php?id=meshtastic:station */
+    HardwareModel_STATION_G1 = 45,  
     /* Reserved ID For developing private Ports. These will show up in live traffic sparsely, so we can use a high number. Keep it within 8 bits. */
     HardwareModel_PRIVATE_HW = 255 
 } HardwareModel;

variants/station-g1/platformio.ini

@@ -0,0 +1,8 @@
+; The 1.0 release of the nano-g1 board 
+[env:station-g1]
+extends = esp32_base
+board = ttgo-t-beam
+lib_deps =
+  ${esp32_base.lib_deps}
+build_flags = 
+  ${esp32_base.build_flags} -D STATION_G1  -I variants/station-g1

variants/station-g1/variant.h

@@ -0,0 +1,36 @@
+// #define BUTTON_NEED_PULLUP // if set we need to turn on the internal CPU pullup during sleep
+
+#define I2C_SDA 21
+#define I2C_SCL 22
+
+#define BUTTON_PIN 36     // The middle button GPIO on the Nano G1
+//#define BUTTON_PIN_ALT 13 // Alternate GPIO for an external button if needed. Does anyone use this? It is not documented anywhere.
+#define EXT_NOTIFY_OUT 13 // Default pin to use for Ext Notify Module.
+
+// common pinout for their SX1262 vs RF95 modules - both can be enabled and we will probe at runtime for RF95 and if
+// not found then probe for SX1262
+#define USE_RF95
+#define USE_SX1262
+
+#define LORA_DIO0 26 // a No connect on the SX1262 module
+#define LORA_RESET 23
+#define LORA_DIO1 33 // SX1262 IRQ
+#define LORA_DIO2 32 // SX1262 BUSY
+#define LORA_DIO3    // Not connected on PCB
+
+#ifdef USE_SX1262
+#define SX126X_CS RF95_NSS // FIXME - we really should define LORA_CS instead
+#define SX126X_DIO1 LORA_DIO1
+#define SX126X_BUSY LORA_DIO2
+#define SX126X_RESET LORA_RESET
+//#define SX126X_E22 // Not really an E22 
+// Internally the module hooks the SX1262-DIO2 in to control the TX/RX switch (which is the default for the sx1262interface
+// code)
+#endif
+
+#define BATTERY_PIN 35    // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
+#define BATTERY_SENSE_SAMPLES 30  //Set the number of samples, It has an effect of increasing sensitivity.
+#define ADC_MULTIPLIER 2.15
+
+// different screen
+#define USE_SH1106