diff --git a/docs/software/plugins/StoreForwardPlugin.md b/docs/software/plugins/StoreForwardPlugin.md
index 129005ba..02389e42 100644
--- a/docs/software/plugins/StoreForwardPlugin.md
+++ b/docs/software/plugins/StoreForwardPlugin.md
@@ -29,6 +29,12 @@ UC 4) support for a mesh to have multiple routers that have the store & forward
 
 UC 5) Support for "long term" delayed messages and "short term" delayed messages. Handle the cases slightly different to improve user expierence. A short term delayed message would be a message that was resent becaue a node was not heard from for <5 minutes. A long term delayed message is a message that has not been delivered in >5 minutes.
 
+UC 6) Eventually we could add a "want_store_and_forward" bit to MeshPacket and that could be nicer than whitelists in this plugin. Initially we'd only set that bit in text messages (and any other plugin messages that can cope with this). This change would be backward wire compatible so can add easily later.
+
+UC 7) Currently the way we allocate messages in the device code is super inefficient. It always allocates the worst case message size. Really we should dynamically allocate just the # of bytes we need. This would allow many more MeshPackets to be kept in RAM.
+
+UC 8) We'll want a "delayed" bit in MeshPacket. This will indicate that the message was not received in real time.
+
 # Things to consider
 
 Not all these cases will be initially implemented. It's just a running stream of thoughts to be considered.
diff --git a/src/RedirectablePrint.cpp b/src/RedirectablePrint.cpp
index 541b55c7..c60b8a50 100644
--- a/src/RedirectablePrint.cpp
+++ b/src/RedirectablePrint.cpp
@@ -78,9 +78,9 @@ size_t RedirectablePrint::logDebug(const char *format, ...)
             int min = (hms % SEC_PER_HOUR) / SEC_PER_MIN;
             int sec = (hms % SEC_PER_HOUR) % SEC_PER_MIN; // or hms % SEC_PER_MIN
 
-            r += printf("%02d:%02d:%02d ", hour, min, sec);
+            r += printf("%02d:%02d:%02d %u ", hour, min, sec, millis() / 1000);
         } else
-            r += printf("??:??:?? ");
+            r += printf("??:??:?? %u ", millis() / 1000);
 
         auto thread = concurrency::OSThread::currentThread;
         if(thread) {
diff --git a/src/configuration.h b/src/configuration.h
index 4fd395fd..cb68a2e3 100644
--- a/src/configuration.h
+++ b/src/configuration.h
@@ -354,9 +354,8 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 
 #define VEXT_ENABLE 21 // active low, powers the oled display and the lora antenna boost
 #define LED_PIN 25     // If defined we will blink this LED
-#define BUTTON_PIN                                                                                                               \
-    12 // If defined, this will be used for user button presses, if your board doesn't have a physical switch, you can wire one
-       // between this pin and ground
+#define BUTTON_PIN 12  // If defined, this will be used for user button presses,
+
 #define BUTTON_NEED_PULLUP
 
 #define USE_RF95
@@ -375,15 +374,16 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define GPS_RESET_N 10
 #define GPS_EXTINT 23 // On MAX-M8 module pin name is EXTINT. On L70 module pin name is STANDBY.
 
-#define BATTERY_PIN 39 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
+#define BATTERY_PIN 39    // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
 #define BATTERY_EN_PIN 14 // Voltage voltage divider enable pin connected to mosfet
 
 #define I2C_SDA 4 // I2C pins for this board
 #define I2C_SCL 2
 
-#define LED_PIN 12     // If defined we will blink this LED
-//#define BUTTON_PIN 36  // If defined, this will be used for user button presses (ToDo problem on that line on debug screen -->   Long press start!)
-//#define BUTTON_NEED_PULLUP //GPIOs 34 to 39 are GPIs – input only pins. These pins don’t have internal pull-ups or pull-down resistors. 
+#define LED_PIN 12 // If defined we will blink this LED
+//#define BUTTON_PIN 36  // If defined, this will be used for user button presses (ToDo problem on that line on debug screen -->
+//Long press start!) #define BUTTON_NEED_PULLUP //GPIOs 34 to 39 are GPIs – input only pins. These pins don’t have internal
+//pull-ups or pull-down resistors.
 
 #define USE_RF95
 #define LORA_DIO0 38 // a No connect on the SX1262 module
diff --git a/src/main.cpp b/src/main.cpp
index bb3ec482..9bd34c23 100644
--- a/src/main.cpp
+++ b/src/main.cpp
@@ -305,12 +305,15 @@ void setup()
 
 #ifdef BUTTON_PIN
 #ifndef NO_ESP32
-    // If BUTTON_PIN is held down during the startup process,
-    //   force the device to go into a SoftAP mode.
     bool forceSoftAP = 0;
+
+    // If the button is connected to GPIO 12, don't enable the ability to use
+    // meshtasticAdmin on the device.
     pinMode(BUTTON_PIN, INPUT);
+
 #ifdef BUTTON_NEED_PULLUP
     gpio_pullup_en((gpio_num_t)BUTTON_PIN);
+    delay(10);
 #endif
 
     // BUTTON_PIN is pulled high by a 12k resistor.
diff --git a/src/plugins/esp32/RangeTestPlugin.cpp b/src/plugins/esp32/RangeTestPlugin.cpp
index fad1991d..d453574f 100644
--- a/src/plugins/esp32/RangeTestPlugin.cpp
+++ b/src/plugins/esp32/RangeTestPlugin.cpp
@@ -37,7 +37,7 @@ int32_t RangeTestPlugin::runOnce()
 
     //radioConfig.preferences.range_test_plugin_enabled = 1;
     //radioConfig.preferences.range_test_plugin_sender = 45;
-    // radioConfig.preferences.range_test_plugin_save = 1;
+    //radioConfig.preferences.range_test_plugin_save = 1;
 
     // Fixed position is useful when testing indoors.
     // radioConfig.preferences.fixed_position = 1;