ppr1 lcd is 'good enough' for now

docs/software/nrf52-TODO.md

@@ -11,8 +11,8 @@
 * fix bluetooth
 * Test GPS
 * make ST7567Wire driver less ugly, move OLED stuff into a common class treee
-* add power save mode for lcd per page 31 of datasheet
-* add power off sequence per datasheet to lcd driver
+* add LCD power save mode for lcd per page 31 of datasheet
+* add LCD power off sequence per datasheet to lcd driver
 * leave LCD screen on most of the time (because it needs little power)
 
 ### general nrf52 TODO:

src/graphics/Screen.cpp

@@ -58,10 +58,6 @@ static char ourId[5];
 static bool heartbeat = false;
 #endif
 
-// We used to use constants for this - now we pull from the device at startup
-//#define SCREEN_WIDTH 128
-//#define SCREEN_HEIGHT 64
-
 static uint16_t displayWidth, displayHeight;
 
 #define SCREEN_WIDTH displayWidth
@@ -85,6 +81,10 @@ static uint16_t displayWidth, displayHeight;
 
 #define getStringCenteredX(s) ((SCREEN_WIDTH - display->getStringWidth(s)) / 2)
 
+#ifndef SCREEN_TRANSITION_MSECS
+#define SCREEN_TRANSITION_MSECS 300
+#endif
+
 static void drawBootScreen(OLEDDisplay *display, OLEDDisplayUiState *state, int16_t x, int16_t y)
 {
     // draw an xbm image.
@@ -636,11 +636,7 @@ void Screen::setup()
     displayWidth = dispdev.width();
     displayHeight = dispdev.height();
 
-    uint16_t transitionTime = 300; // msecs
-#ifdef HAS_EINK
-    transitionTime = 0;
-#endif
-    ui.setTimePerTransition(transitionTime);  
+    ui.setTimePerTransition(SCREEN_TRANSITION_MSECS);  
 
     ui.setIndicatorPosition(BOTTOM);
     // Defines where the first frame is located in the bar.
@@ -882,12 +878,16 @@ void Screen::handleOnPress()
     }
 }
 
+#ifndef SCREEN_TRANSITION_FRAMERATE
+#define SCREEN_TRANSITION_FRAMERATE 30 // fps
+#endif
+
 void Screen::setFastFramerate()
 {
     DEBUG_MSG("Setting fast framerate\n");
 
     // We are about to start a transition so speed up fps
-    targetFramerate = TRANSITION_FRAMERATE;
+    targetFramerate = SCREEN_TRANSITION_FRAMERATE;
     ui.setTargetFPS(targetFramerate);
     setInterval(0); // redraw ASAP
 }

src/graphics/configs.h

@@ -3,7 +3,6 @@
 #include "fonts.h"
 
 // This means the *visible* area (sh1106 can address 132, but shows 128 for example)
-#define TRANSITION_FRAMERATE 30 // fps
 #define IDLE_FRAMERATE 1        // in fps
 #define COMPASS_DIAM 44
 

variants/eink/variant.h

@@ -209,6 +209,9 @@ External serial flash WP25R1635FZUIL0
 
 #define HAS_EINK
 
+// No screen wipes on eink
+#define SCREEN_TRANSITION_MSECS 0
+
 #define PIN_SPI1_MISO                                                                                                            \
     (32 + 7) // FIXME not really needed, but for now the SPI code requires something to be defined, pick an used GPIO
 #define PIN_SPI1_MOSI PIN_EINK_MOSI

variants/ppr1/variant.h

@@ -122,6 +122,10 @@ static const uint8_t AREF = PIN_AREF;
 // Define if screen should be mirrored left to right
 #define SCREEN_MIRROR
 
+// LCD screens are slow, so slowdown the wipe so it looks better
+#define SCREEN_TRANSITION_MSECS 1000
+#define SCREEN_TRANSITION_FRAMERATE 10 // fps
+
 /*
  * SPI Interfaces
  */