diff --git a/bin/qspi-flash-test.sh b/bin/qspi-flash-test.sh
new file mode 100755
index 00000000..7fc186b5
--- /dev/null
+++ b/bin/qspi-flash-test.sh
@@ -0,0 +1,6 @@
+# You probably don't need this - it is a basic test of the serial flash on the TTGO eink board
+
+nrfjprog -qspiini nrf52/ttgo_eink_qpsi.ini --qspieraseall
+nrfjprog --qspiini nrf52/ttgo_eink_qpsi.ini --memwr 0x12000000 --val 0xdeadbeef --verify
+nrfjprog --qspiini nrf52/ttgo_eink_qpsi.ini --readqspi spi.hex
+objdump -s spi.hex | less
diff --git a/nrf52/ttgo_eink_qpsi.ini b/nrf52/ttgo_eink_qpsi.ini
new file mode 100644
index 00000000..d477db8e
--- /dev/null
+++ b/nrf52/ttgo_eink_qpsi.ini
@@ -0,0 +1,69 @@
+; nrfjprog.exe configuration file.
+
+; Note: QSPI flash is mapped into memory at address 0x12000000
+
+[DEFAULT_CONFIGURATION]
+; Define the capacity of the flash memory device in bytes. Set to 0 if no external memory device is present in your board.
+; MX25R1635F is 16Mbit/2Mbyte
+MemSize = 0x200000
+
+; Define the desired ReadMode. Valid options are FASTREAD, READ2O, READ2IO, READ4O and READ4IO
+ReadMode = READ2IO
+
+; Define the desired WriteMode. Valid options are PP, PP2O, PP4O and PP4IO
+WriteMode = PP
+
+; Define the desired AddressMode. Valid options are BIT24 and BIT32
+AddressMode = BIT24
+
+; Define the desired Frequency. Valid options are M2, M4, M8, M16 and M32
+Frequency = M16
+
+; Define the desired SPI mode. Valid options are MODE0 and MODE3
+SpiMode = MODE0
+
+; Define the desired SckDelay. Valid options are in the range 0 to 255
+SckDelay = 0x80
+
+; Define the desired IO level for DIO2 and DIO3 during a custom instruction. Valid options are LEVEL_HIGH and LEVEL_LOW
+CustomInstructionIO2Level = LEVEL_LOW
+CustomInstructionIO3Level = LEVEL_HIGH
+
+; Define the assigned pins for the QSPI peripheral. Valid options are those existing in your device
+CSNPin = 15
+CSNPort = 1
+SCKPin = 14
+SCKPort = 1
+DIO0Pin = 12
+DIO0Port = 1
+DIO1Pin = 13
+DIO1Port = 1
+
+;These two pins are not connected, but we must name something
+DIO2Pin = 3
+DIO2Port = 1
+DIO3Pin = 5
+DIO3Port = 1
+
+; Define the Index of the Write In Progress (WIP) bit in the status register. Valid options are in the range of 0 to 7.
+WIPIndex = 0
+
+; Define page size for commands. Valid sizes are PAGE256 and PAGE512.
+PPSize = PAGE256
+
+; Custom instructions to send to the external memory after initialization. Format is instruction code plus data to send in between optional brakets. 
+; These instructions will be executed each time the qspi peripheral is initiated by nrfjprog. 
+; To improve execution speed on consecutive interations with QSPI, you can run nrfjprog once with custom initialization, and then comment out the lines below.
+; Numbers can be given in decimal, hex (starting with either 0x or 0X) and binary (starting with either 0b or 0B) formats. 
+; The custom instructions will be executed in the order found. 
+
+; This example includes two commands, first a WREN (WRite ENable) and then a WRSR (WRite Satus Register) enabling the Quad Operation and the High Performance
+; mode for the MX25R6435F memory present in the nRF52840 DK.
+;InitializationCustomInstruction =  0x06
+;InitializationCustomInstruction =  0x01, [0x40, 0, 0x2]
+
+; For MX25R1635F on TTGO board, only two data lines are connected
+; This example includes two commands, first a WREN (WRite ENable) and then a WRSR (WRite Satus Register) disabling Quad Operation and the High Performance
+; mode.  For normal operation you might want low power mode instead.
+InitializationCustomInstruction =  0x06
+InitializationCustomInstruction =  0x01, [0x00, 0, 0x2]
diff --git a/variants/eink/variant.h b/variants/eink/variant.h
index 6ab4e073..c1781c84 100644
--- a/variants/eink/variant.h
+++ b/variants/eink/variant.h
@@ -30,7 +30,7 @@
 soonish:
 hook cdc acm device to debug output
 fix bootloader to use two buttons - remove bootloader hacks
-get second button working in app load
+DONE get second button working in app load
 fix display width and height
 clean up eink drawing to not have the nasty timeout hack
 measure current draws
@@ -48,8 +48,14 @@ add factory/power on self test
 use tp_ser_io as a button, it goes high when pressed unify eink display classes
 
 feedback to give:
-remove ipx connector for nfc, instead use two caps and loop traces on the back of the board as an antenna?
 
+* remove ipx connector for nfc, instead use two caps and loop traces on the back of the board as an antenna?
+
+* I've made the serial flash chip work, but if you do a new spin of the board I recommend:
+connect pin 3 and pin 7 of U4 to spare GPIOs on the processor (instead of their current connections), 
+This would allow using 4 bit wide interface mode to the serial flash.
+doubling the transfer speed! see example here:
+https://infocenter.nordicsemi.com/topic/ug_nrf52840_dk/UG/nrf52840_DK/hw_external_memory.html?cp=4_0_4_7_4
 */
 
 /*----------------------------------------------------------------------------
@@ -108,11 +114,10 @@ static const uint8_t A0 = PIN_A0;
  */
 
 /*
-This serial port is _also_ connected to the incoming D+/D- pins from the USB header.  FIXME, figure out how that is supposed to
-work.
+No longer populated on PCB
 */
-#define PIN_SERIAL2_RX (0 + 6)
-#define PIN_SERIAL2_TX (0 + 8)
+//#define PIN_SERIAL2_RX (0 + 6)
+//#define PIN_SERIAL2_TX (0 + 8)
 // #define PIN_SERIAL2_EN (0 + 17)
 
 /**
@@ -130,23 +135,21 @@ work.
 #define PIN_RTC_INT (0 + 16) // Interrupt from the PCF8563 RTC
 
 /*
-
-FIXME define/FIX flash access
+External serial flash WP25R1635FZUIL0
+*/
 
 // QSPI Pins
-#define PIN_QSPI_SCK 19
-#define PIN_QSPI_CS 17
-#define PIN_QSPI_IO0 20
-#define PIN_QSPI_IO1 21
-#define PIN_QSPI_IO2 22
-#define PIN_QSPI_IO3 23
+#define PIN_QSPI_SCK (32 + 14)
+#define PIN_QSPI_CS (32 + 15)
+#define PIN_QSPI_IO0 (32 + 12) // MOSI if using two bit interface
+#define PIN_QSPI_IO1 (32 + 13) // MISO if using two bit interface
+//#define PIN_QSPI_IO2 22 // WP if using two bit interface (i.e. not used)
+//#define PIN_QSPI_IO3 23 // HOLD if using two bit interface (i.e. not used)
 
 // On-board QSPI Flash
-#define EXTERNAL_FLASH_DEVICES MX25R6435F
+#define EXTERNAL_FLASH_DEVICES MX25R1635F
 #define EXTERNAL_FLASH_USE_QSPI
 
-*/
-
 /*
  * Lora radio
  */