use common param name `SX126X_ANT_SW` instead of the `SX1262_ANT_SW`

src/main.cpp

@@ -492,16 +492,10 @@ void setup()
         }
     }
 
-#ifdef SX1262_ANT_SW
-    // make analog PA vs not PA switch on SX1262 eval board work properly
-    pinMode(SX1262_ANT_SW, OUTPUT);
-    digitalWrite(SX1262_ANT_SW, 1);
-#endif
-
-#ifdef SX1268_ANT_SW
-    // make analog PA vs not PA switch on SX1268 eval board work properly
-    pinMode(SX1268_ANT_SW, OUTPUT);
-    digitalWrite(SX1268_ANT_SW, 1);
+#ifdef SX126X_ANT_SW
+    // make analog PA vs not PA switch on SX126x eval board work properly
+    pinMode(SX126X_ANT_SW, OUTPUT);
+    digitalWrite(SX126X_ANT_SW, 1);
 #endif
 
     // radio init MUST BE AFTER service.init, so we have our radio config settings (from nodedb init)

variants/lora_relay_v1/variant.h

@@ -126,7 +126,7 @@ static const uint8_t SCK = PIN_SPI_SCK;
 #define SX1262_DIO2 (30)
 #define SX126X_BUSY (33) // Supposed to be P0.18 but because of reworks, now on P0.31 (18)
 #define SX126X_RESET (34)
-// #define SX1262_ANT_SW (32 + 10)
+// #define SX126X_ANT_SW (32 + 10)
 #define SX126X_RXEN (14)
 #define SX126X_TXEN (31)
 #define SX126X_POWER_EN                                                                                                          \

variants/lora_relay_v2/variant.h

@@ -146,7 +146,7 @@ static const uint8_t SCK = PIN_SPI_SCK;
 #define SX1262_DIO2 (30)
 #define SX126X_BUSY (33) // Supposed to be P0.18 but because of reworks, now on P0.31 (18)
 #define SX126X_RESET (34)
-// #define SX1262_ANT_SW (32 + 10)
+// #define SX126X_ANT_SW (32 + 10)
 #define SX126X_RXEN (14)
 #define SX126X_TXEN (31)
 #define SX126X_POWER_EN                                                                                                          \

variants/pca10056-rc-clock/variant.h

@@ -144,7 +144,7 @@ static const uint8_t SCK = PIN_SPI_SCK;
 #define SX126X_DIO1 (32 + 6)    // P1.06
 #define SX126X_BUSY (32 + 4)    // P1.04
 #define SX126X_RESET (0 + 3)    // P0.03
-#define SX1262_ANT_SW (32 + 10) // P1.10
+#define SX126X_ANT_SW (32 + 10) // P1.10
 
 // To debug via the segger JLINK console rather than the CDC-ACM serial device
 // #define USE_SEGGER

variants/ppr/variant.h

@@ -134,7 +134,7 @@ static const uint8_t SCK = PIN_SPI_SCK;
 #define SX1262_DIO2 (26)
 #define SX126X_BUSY (31) // Supposed to be P0.18 but because of reworks, now on P0.31 (18)
 #define SX126X_RESET (17)
-// #define SX1262_ANT_SW (32 + 10)
+// #define SX126X_ANT_SW (32 + 10)
 #define SX126X_RXEN (22)
 #define SX126X_TXEN (24)
 #define SX126X_E22  // Indicates this SX1262 is inside of an ebyte E22 module and special config should be done for that