kopia lustrzana https://gitlab.com/eliggett/wfview
173 wiersze
3.3 KiB
Plaintext
173 wiersze
3.3 KiB
Plaintext
|
|
|
|
View:
|
|
|
|
|
|
buttons
|
|
|
|
spectrum scope/waterfall:
|
|
|
|
spectrum mode
|
|
|
|
depending on the rig you can select:
|
|
|
|
center
|
|
fixed
|
|
scroll-center
|
|
scroll-fixed
|
|
|
|
spectrum span
|
|
|
|
the spectrum span is active in center modes and you can select
|
|
here the span you like, just as on the rig.
|
|
|
|
spectrum edge
|
|
|
|
here you can select the edge number as programmed in the rig.
|
|
Most rigs will accept four edges.
|
|
|
|
|
|
tofixed
|
|
|
|
clear peaks
|
|
|
|
here you can clear the peaks. Currently we only support persistent
|
|
peaks and at some point we are changing that to be able to have it
|
|
go away after 10 seconds, like the rig does.
|
|
|
|
enable/disable wf
|
|
|
|
on/off switch for the scope/waterfall
|
|
|
|
wf theme
|
|
|
|
Currently fixed selections how the scope and waterfall look like
|
|
with colors. At som epoint we may add the ability to accept the
|
|
RGB values like the rig does.
|
|
|
|
|
|
|
|
mode
|
|
|
|
|
|
here you can select the mode used for tx and rx. To enable data mode there is
|
|
a separate button to select.
|
|
|
|
|
|
Data mode
|
|
|
|
switch the D mode on/off on the selected mode.
|
|
|
|
receive (and tx) filter
|
|
|
|
Select the predefined filter settings of the rig.
|
|
Rigs also will change the TX width accordingly.
|
|
|
|
transmit/receive
|
|
|
|
this button alternates between TX and RX; Note that to
|
|
enable TX, you need to do that first on the Settings tab
|
|
|
|
enable/disable atu
|
|
|
|
if your rig supports an internal ATU, you can enable
|
|
disable it here. Note that we have not tested external
|
|
ATU's yet. It may follow, it may not...
|
|
|
|
enable/disable rit
|
|
|
|
Enable the RIT function; currently no feedback on the rx shift.
|
|
|
|
tune
|
|
|
|
Button to initiate the ATU. Note that we have not tested external
|
|
ATU's yet. It may follow, it may not...
|
|
|
|
|
|
repeater setup (expand)
|
|
|
|
TODO
|
|
|
|
preamp
|
|
|
|
You can select the preamp mode(s). Some rigs can only accept
|
|
preamp OR att.
|
|
|
|
attenuator
|
|
|
|
you can select the rig attenuator here. Some rigs can only accept
|
|
preamp OR att.
|
|
|
|
|
|
antenna selection
|
|
|
|
TODO
|
|
|
|
controls
|
|
|
|
main dial (there is no sub dial yet)
|
|
|
|
by turning the dial, or using mouse wheel or clicking on the scope
|
|
you can change the current frequency. The step size is below the
|
|
main dial and you can select most known stepsizes there.
|
|
An Flock button will effectively lock the freq to prevent accidental
|
|
mis clicking/rotating mouse actions.
|
|
|
|
|
|
rit dial
|
|
|
|
the rit dial will effectively modify the offset in RX; useful on the VHF
|
|
bands and up. Note that you need to switch on RIT for that
|
|
You can use the mouse wheel to change the offset/shift.
|
|
|
|
rf gain
|
|
|
|
This slider controls the RF gain of the rig
|
|
|
|
af gain (defaults to 100%
|
|
|
|
This controls the AF Gain locally, defaults to 100% and does not
|
|
increase/decrease the AF gain on the rig itself.
|
|
(Else, a remotely controlled rig could make a lot of noise ;-))
|
|
|
|
sq
|
|
|
|
The squelch control
|
|
|
|
tx power
|
|
|
|
Control that sets the power in % with the same accuracy as the rig
|
|
so if your rig is 50 Watt at 47%, this slider will too.
|
|
|
|
mic gain
|
|
|
|
The mic gain slider sets the modulation level on the rig.
|
|
|
|
scope reference level
|
|
|
|
The scope reference level can be set here and TODO because
|
|
need to check if this follows per band or not.
|
|
|
|
|
|
=============================
|
|
Frequency
|
|
|
|
On this tab you can insert a free frequency in kHz.
|
|
|
|
examples:
|
|
|
|
7100 --> 7.1 kHz
|
|
430. --> 430 MHz
|
|
|
|
e.g. the dot itself defines currently that you specify MHz.
|
|
It will not accept anything beyond the dot. E.g. 430.125
|
|
will end up doing nothing.
|
|
|
|
After entering, you will be switched back to the View tab.
|
|
|
|
STO/RCL: TODO
|
|
|
|
Settings
|
|
|
|
|