mirror
/
usdx
kopia lustrzana https://github.com/threeme3/usdx
1
0
Forkuj 0
Kod Zgłoszenia Projekty Wydania Wiki Aktywność

Minor changes.

pull/11/head
guido 2020-08-13 13:15:38 +02:00
rodzic 22b3f595c7
commit 8fb2dd723f
1 zmienionych plików z 9 dodań i 9 usunięć
Pokaż statystyki Ściągnij plik aktualizacji Ściągnij plik porównania Expand all files Collapse all files

18
QCX-SSB.ino
Wyświetl plik

@ -8,9 +8,9 @@
#define QCX 1 // When not using a uSDX: QCX specific features (QCX, QCX-SSB, QCX-DSP with alignment-feature) (disable this to safe memory)
//#define DEBUG 1 // Hardware diagnostics (disable this to safe memory)
#define DEBUG 1 // Hardware diagnostics (disable this to safe memory)
#define KEYER 1 // CW keyer
#define CAT 1 // CAT-interface
//#define CAT 1 // CAT-interface
#define F_XTAL 27005000 // 27MHz SI5351 crystal
//#define F_XTAL 25004000 // 25MHz SI5351 crystal (enable for uSDX-Barb or using a si5351 break-out board)
//#define SWAP_ROTARY 1 // Swap rotary direction (enable for uSDX-Barb)
@ -178,8 +178,8 @@ public: // LCD1602 display in 4-bit mode, RS is pull-up and kept low when idle
// To prevent that LCD writes are received by the serial receiver, PC2 is made HIGH during writes to pull-up TXD via a diode.
// The RXD, TXD lines are connected to the host via 1k resistors, a 1N4148 is placed between PC2 (anode) and the TXD resistor.
// There are two drawbacks when continuous LCD writes happen: 1. noise is leaking via the AREF pull-ups into the receiver 2. serial data cannot be received.
void pre(){ Serial.flush(); PORTC |= 1<<2; DDRC |= 1<<2; UCSR0B &= ~((1<<RXEN0)|(1<<TXEN0)); } // Wait until serial TX stops; make PC2 high (to pull-up TXD); disable serial port (PD0, PD1)
void post(){ UCSR0B |= (1<<RXEN0)|(1<<TXEN0); DDRC &= ~(1<<2); } // Enable serial port (PD0, PD1); disable PC2
void pre(){ Serial.flush(); PORTC |= 1<<2; DDRC |= 1<<2; UCSR0B &= ~((1<<RXEN0)|(1<<TXEN0)); } // Wait until serial TX stops; make PC2 high (to pull-up TXD); enable PD0/PD1 - disable serial port
void post(){ UCSR0B |= (1<<RXEN0)|(1<<TXEN0); DDRC &= ~(1<<2); } // Enable serial port - disable PD0, PD1; disable PC2
#else
void pre(){}
void post(){}
@ -2855,9 +2855,9 @@ uint32_t sec_event_time = 0;
static uint8_t pwm_min = 0; // PWM value for which PA reaches its minimum: 29 when C31 installed; 0 when C31 removed; 0 for biasing BS170 directly
#ifdef QCX
static uint8_t pwm_max = 220; // PWM value for which PA reaches its maximum: 96 when C31 installed; 255 when C31 removed; 220 for biasing BS170 directly
static uint8_t pwm_max = 255; // PWM value for which PA reaches its maximum: 96 when C31 installed; 255 when C31 removed;
#else
static uint8_t pwm_max = 128;
static uint8_t pwm_max = 128; // PWM value for which PA reaches its maximum: 128 for biasing BS170 directly
#endif
const char* offon_label[2] = {"OFF", "ON"};
@ -2896,7 +2896,7 @@ void paramAction(uint8_t action, uint8_t id = ALL) // list of parameters
case AGC: paramAction(action, agc, F("1.6"), F("AGC"), offon_label, 0, 1, false); break;
case NR: paramAction(action, nr, F("1.7"), F("NR"), NULL, 0, 8, false); break;
case ATT: paramAction(action, att, F("1.8"), F("ATT"), att_label, 0, 7, false); break;
case ATT2: paramAction(action, att2, F("1.9"), F("ATT2"), NULL, 3 /*0*/, 16, false); break;
case ATT2: paramAction(action, att2, F("1.9"), F("ATT2"), NULL, 2 /*0*/, 16, false); break;
case SMETER: paramAction(action, smode, F("1.10"), F("S-meter"), smode_label, 0, _N(smode_label) - 1, false); break;
case CWDEC: paramAction(action, cwdec, F("2.1"), F("CW Decoder"), offon_label, 0, 1, false); break;
case CWTONE: paramAction(action, cw_tone, F("2.2"), F("CW Tone"), cw_tone_label, 0, 1, false); break;
@ -2964,7 +2964,7 @@ void initPins(){
}
#ifdef CAT
// CAT support from Charlie Morris, ZL2CTM, source: http://zl2ctm.blogspot.com/2020/06/digital-modes-transceiver.html?m=1
// CAT support inspired by Charlie Morris, ZL2CTM, source: http://zl2ctm.blogspot.com/2020/06/digital-modes-transceiver.html?m=1
// https://www.kenwood.com/i/products/info/amateur/ts_480/pdf/ts_480_pc.pdf
#define CATCMD_SIZE 32
char CATcmd[CATCMD_SIZE];
@ -3435,7 +3435,7 @@ void setup()
#ifndef OLED
smode = 0; // In case of LCD, turn of smeter
#endif
#endif
#endif //TESTBENCH
#ifdef CAT
//use 38k4 for WSJT-X 2.2.2 TS-480 protocol other lower or higher speed can cause problems