sdrangel/plugins/samplesource/fcdpro/readme.md

87 wiersze
3.6 KiB
Markdown
Czysty Zwykły widok Historia

2019-01-05 00:04:26 +00:00
<h1>FunCube Dongle Pro input plugin</h1>
<h2>Introduction</h2>
This input sample source plugin gets its samples from a [FunCube Dongle (FCD) Pro device](http://www.funcubedongle.com/?page_id=1057).
<h2>Interface</h2>
![FCD Pro input plugin GUI](../../../doc/img/FCDPro_plugin.png)
<h3>1: Common stream parameters</h3>
![Remote source input stream GUI](../../../doc/img/RemoteInput_plugin_01.png)
2019-01-05 00:04:26 +00:00
<h4>1.1: Frequency</h4>
This is the center frequency of reception in kHz.
<h4>1.2: Start/Stop</h4>
Device start / stop button.
- Blue triangle icon: device is ready and can be started
- Green square icon: device is running and can be stopped
- Magenta (or pink) square icon: an error occurred. In the case the device was accidentally disconnected you may click on the icon, plug back in and start again.
<h4>1.4: Stream sample rate</h4>
Baseband I/Q sample rate in kS/s. This is the device sample rate (4) divided by the decimation factor (6).
<h3>2: Local Oscillator correction</h3>
This is the correction to be applied to the local oscillator in ppm.
<h3>3: Auto correction options</h3>
These buttons control the local DSP auto correction options:
- **DC**: auto remove DC component
- **IQ**: auto make I/Q balance. The DC correction must be enabled for this to be effective.
<h3>4: Decimated bandpass center frequency position relative the FCD Pro center frequency</h3>
- **Cen**: the decimation operation takes place around the FCD Pro center frequency Fs
- **Inf**: the decimation operation takes place around Fs - Fc.
- **Sup**: the decimation operation takes place around Fs + Fc.
With SR as the sample rate before decimation Fc is calculated as:
- if decimation n is 4 or lower: Fc = SR/2^(log2(n)-1). The device center frequency is on the side of the baseband. You need a RF filter bandwidth at least twice the baseband.
- if decimation n is 8 or higher: Fc = SR/n. The device center frequency is half the baseband away from the side of the baseband. You need a RF filter bandwidth at least 3 times the baseband.
<h3>5: Decimation factor</h3>
The I/Q stream from the FCD Pro ADC is downsampled by a power of two before being sent to the passband. Possible values are increasing powers of two: 1 (no decimation), 2, 4, 8, 16.
<h3>6: Transverter mode open dialog</h3>
2020-06-23 03:02:00 +00:00
This button opens a dialog to set the transverter mode frequency translation options. The details about this dialog can be found [here](../../../sdrgui/gui/transverterdialog.md)
2019-01-05 00:04:26 +00:00
<h3>7: Set default values</h3>
Use this oush button to force default reasonable values for all parameters below (8)
<h3>8: Parameters</h3>
This panel lists all parameters that are the same as in the Windows utility interface showing the block diagram of the FCD:
![FCD Pro parameters](../../../doc/img/FCDPro_fchid.png)
- **LNA Enh**: equivalent of the "LNA enhance" parameter
- **Band**: equivalent of the "Band" parameter
- **Bias**: equivalent of the "Bias current" parameter
- **Mode**: equivalent of the "IF gain mode" parameter
- **LNA G**: equivalent of the "LNA gain" parameter
- **RF filt**: equivalent of the "RF filter" parameter
- **Mix G**: equivalent of the "Mixer gain" parameter
- **Mix filter**: equivalent of the "Mixer filter" parameter
- **Gain1**: equivalent of the "IF gain 1" parameter
- **RC filt**: equivalent of the "IF RC filter" parameter
- **Gain2**: equivalent of the "IF gain 2" parameter
- **Gain3**: equivalent of the "IF gain 3" parameter
- **Gain4**: equivalent of the "IF gain 4" parameter
- **IF filt**: equivalent of the "IF filter" parameter
- **Gain5**: equivalent of the "IF gain 5" parameter
- **Gain6**: equivalent of the "IF gain 6" parameter