kopia lustrzana https://gitlab.com/sane-project/website
80 wiersze
3.5 KiB
HTML
80 wiersze
3.5 KiB
HTML
<!-- received="Sat Mar 21 06:00:36 1998 PST" -->
|
||
<!-- sent="Sat, 21 Mar 1998 16:03:06 +0100" -->
|
||
<!-- name="Olaf Ronneberger" -->
|
||
<!-- email="Olaf.Ronneberger@dlr.de" -->
|
||
<!-- subject="Mustek MFC-600S damaged by scanimage - what now?" -->
|
||
<!-- id="" -->
|
||
<!-- inreplyto="" -->
|
||
<title>sane-devel: Mustek MFC-600S damaged by scanimage - what now?</title>
|
||
<h1>Mustek MFC-600S damaged by scanimage - what now?</h1>
|
||
<b>Olaf Ronneberger</b> (<a href="mailto:Olaf.Ronneberger@dlr.de"><i>Olaf.Ronneberger@dlr.de</i></a>)<br>
|
||
<i>Sat, 21 Mar 1998 16:03:06 +0100</i>
|
||
<p>
|
||
<ul>
|
||
<li> <b>Messages sorted by:</b> <a href="date.html#143">[ date ]</a><a href="index.html#143">[ thread ]</a><a href="subject.html#143">[ subject ]</a><a href="author.html#143">[ author ]</a>
|
||
<!-- next="start" -->
|
||
<li> <b>Next message:</b> <a href="0144.html">Kaz Sasayama: "Re: epson via parallel"</a>
|
||
<li> <b>Previous message:</b> <a href="0142.html">Hugo van der Kooij: "Re: Updated patches for GTK+ 0.99.7 support"</a>
|
||
<!-- nextthread="start" -->
|
||
<li> <b>Next in thread:</b> <a href="0181.html">Olaf Ronneberger: "Re: Mustek MFC-600S damaged by scanimage - what now?"</a>
|
||
<li> <b>Reply:</b> <a href="0181.html">Olaf Ronneberger: "Re: Mustek MFC-600S damaged by scanimage - what now?"</a>
|
||
<!-- reply="end" -->
|
||
</ul>
|
||
<!-- body="start" -->
|
||
Hi there!<br>
|
||
<p>
|
||
My equipment is as follows:<br>
|
||
<p>
|
||
- Mustek MFC-600S Scanner<br>
|
||
- sane-0.71<br>
|
||
- linux 2.0.31 (German SUSE Distribution -- similar to RedHat)<br>
|
||
- NCR - SCSI-card<br>
|
||
<p>
|
||
All went fine. I just installed sane and got good results using<br>
|
||
xscanimage. Then I tried <br>
|
||
<p>
|
||
scanimge -d mustek --resolution 300 > test.pnm<br>
|
||
<p>
|
||
The slider of the scanner didn't stop at the end of the physical scan<br>
|
||
area and the mechanism produced a loud noise (creek, creek, creek ...).<br>
|
||
I switched it off immediately, but when I switched it on again, only one<br>
|
||
side of the slider was pulled back, and the slider got stuck. <br>
|
||
<p>
|
||
I opened the scanner and found a wire-cable besides the cable drum near<br>
|
||
the motor. I put it back onto this drum and the slider now moves as<br>
|
||
before, but I have colored vertical stripes on each scan. Even in<br>
|
||
Gray-mode there is a light stripe on the image.<br>
|
||
<p>
|
||
I get exacty the same vertical stripes on my Macintosh with original<br>
|
||
Mustek-Software, so it is neither an SCSI- nor a software Problem.<br>
|
||
<p>
|
||
My questions are now:<br>
|
||
<p>
|
||
- Has anyone had already the same problem?<br>
|
||
- Is it possible to fix it myself (I found two screws at the end<br>
|
||
of the cables -- perhaps they are for adjustment)?<br>
|
||
- Where is the CCD-Line located and how does the scanner separate <br>
|
||
the blue green and yellow light?<br>
|
||
- What is wrong with scanimage? The scanner works fine with xscanimage<br>
|
||
<p>
|
||
Thanks in advance.<br>
|
||
<p>
|
||
Olaf<br>
|
||
<p>
|
||
<pre>
|
||
--
|
||
Source code, list archive, and docs: <a href="http://www.mostang.com/sane/">http://www.mostang.com/sane/</a>
|
||
To unsubscribe: echo unsubscribe sane-devel | mail <a href="mailto:majordomo@mostang.com">majordomo@mostang.com</a>
|
||
</pre>
|
||
<!-- body="end" -->
|
||
<p>
|
||
<ul>
|
||
<!-- next="start" -->
|
||
<li> <b>Next message:</b> <a href="0144.html">Kaz Sasayama: "Re: epson via parallel"</a>
|
||
<li> <b>Previous message:</b> <a href="0142.html">Hugo van der Kooij: "Re: Updated patches for GTK+ 0.99.7 support"</a>
|
||
<!-- nextthread="start" -->
|
||
<li> <b>Next in thread:</b> <a href="0181.html">Olaf Ronneberger: "Re: Mustek MFC-600S damaged by scanimage - what now?"</a>
|
||
<li> <b>Reply:</b> <a href="0181.html">Olaf Ronneberger: "Re: Mustek MFC-600S damaged by scanimage - what now?"</a>
|
||
<!-- reply="end" -->
|
||
</ul>
|