sane-project-website/old-archive/1998-06/0069.html

76 wiersze
3.7 KiB
HTML

<!-- received="Sun Jun 7 19:47:54 1998 PDT" -->
<!-- sent="Sun, 7 Jun 1998 19:47:52 -0700" -->
<!-- name="David Mosberger-Tang" -->
<!-- email="David.Mosberger@acm.org" -->
<!-- subject="Re: Problems with Scanning !!!" -->
<!-- id="199806080247.TAA24509@panda.mostang.com" -->
<!-- inreplyto="35770D9F.3B1B4C6F@kassel.netsurf.de" -->
<title>sane-devel: Re: Problems with Scanning !!!</title>
<h1>Re: Problems with Scanning !!!</h1>
<b>David Mosberger-Tang</b> (<a href="mailto:David.Mosberger@acm.org"><i>David.Mosberger@acm.org</i></a>)<br>
<i>Sun, 7 Jun 1998 19:47:52 -0700</i>
<p>
<ul>
<li> <b>Messages sorted by:</b> <a href="date.html#69">[ date ]</a><a href="index.html#69">[ thread ]</a><a href="subject.html#69">[ subject ]</a><a href="author.html#69">[ author ]</a>
<!-- next="start" -->
<li> <b>Next message:</b> <a href="0070.html">Sylvain Gamel: "Support for IS-22 Scanner Cartridge for canon printer"</a>
<li> <b>Previous message:</b> <a href="0068.html">David Mosberger-Tang: "Re: Problems with CANCEL"</a>
<!-- nextthread="start" -->
<!-- reply="end" -->
</ul>
<!-- body="start" -->
<i>&gt;&gt;&gt;&gt;&gt; On Thu, 04 Jun 1998 23:11:59 +0200, Ingo Witzky &lt;<a href="mailto:ingo.witzky@kassel.netsurf.de">ingo.witzky@kassel.netsurf.de</a>&gt; said:</i><br>
<p>
Ingo&gt; Hello. I have a problem. I have the "Mustek 600 II CD "<br>
Ingo&gt; One-Pass-SCSI-scanner. His scsi-name is "SCANNER" his<br>
Ingo&gt; firmware is "2.03" !!! (SCSI-ID: "SCANNER 2.03") He is on<br>
Ingo&gt; device "/dev/sg0" !!! I use the Debian 1.3.1 Distribution of<br>
Ingo&gt; Linux !!! Sane was compiled without any failuremessages. My<br>
Ingo&gt; "xscanimage" runs rigt but don't scan like under Windows 95<br>
Ingo&gt; the real Twain-program !!!<br>
<p>
That's a lot of bangs for one paragraph. ;-)<br>
<p>
Ingo&gt; Problem: My Preview scans the preview in 11 parts. Even in<br>
Ingo&gt; monochrome Mode ! Is there a possibility to make this Preview<br>
Ingo&gt; in one Part like under Windows ?? He only scans Parts of less<br>
Ingo&gt; than one inch at the real scan, but i have put into the<br>
Ingo&gt; mustek.conf to scan a strip-hight of 5 inches !!!! He scans<br>
Ingo&gt; only 0.5 inch and then he goes back a little bit and scans the<br>
Ingo&gt; next 0.5 inch !!! Under Windows he scans the whole Page with<br>
Ingo&gt; only 5 parts !!!!<br>
<p>
Please read the man page sane-mustek(5). It talks about this.<br>
Particularly the option "strip-height" should be of interest to you.<br>
Also, you might want to increase the size of the sg-scsi buffer (see<br>
sanei-scsi(5)).<br>
<p>
Ingo&gt; What can I do to solve this problem and what must I do to<br>
Ingo&gt; configure xscanimage so that he only uses the Mustek Scanner<br>
Ingo&gt; and don't show me the Device pnm:0 and pnm:1 ????<br>
<p>
Read sane-dll(5). You'll probably want to comment out all lines in<br>
dll.conf except for "mustek".<br>
<p>
Ingo&gt; P.S.: Excuse me for bad English !!!! I'm German !!!<br>
<p>
Your English is fine, but you may want to avoid ending each sentence<br>
with a bang. Few people like being shouted at.<br>
<p>
--david<br>
<p>
<pre>
--
Source code, list archive, and docs: <a href="http://www.mostang.com/sane/">http://www.mostang.com/sane/</a>
To unsubscribe: echo unsubscribe sane-devel | mail <a href="mailto:majordomo@mostang.com">majordomo@mostang.com</a>
</pre>
<!-- body="end" -->
<p>
<ul>
<!-- next="start" -->
<li> <b>Next message:</b> <a href="0070.html">Sylvain Gamel: "Support for IS-22 Scanner Cartridge for canon printer"</a>
<li> <b>Previous message:</b> <a href="0068.html">David Mosberger-Tang: "Re: Problems with CANCEL"</a>
<!-- nextthread="start" -->
<!-- reply="end" -->
</ul>