kopia lustrzana https://gitlab.com/sane-project/website
66 wiersze
3.3 KiB
HTML
66 wiersze
3.3 KiB
HTML
<!-- received="Fri Mar 6 10:25:33 1998 PST" -->
|
|
<!-- sent="Fri, 6 Mar 1998 13:29:23 -0500 (EST)" -->
|
|
<!-- name="Mark" -->
|
|
<!-- email="kestrel@falcon.warren-wilson.edu" -->
|
|
<!-- subject="Re: sane 0.71 and microtek E3" -->
|
|
<!-- id="h³" -->
|
|
<!-- inreplyto="35003648.2AD504F1@kootenay.com" -->
|
|
<title>sane-devel: Re: sane 0.71 and microtek E3</title>
|
|
<h1>Re: sane 0.71 and microtek E3</h1>
|
|
<b>Mark</b> (<a href="mailto:kestrel@falcon.warren-wilson.edu"><i>kestrel@falcon.warren-wilson.edu</i></a>)<br>
|
|
<i>Fri, 6 Mar 1998 13:29:23 -0500 (EST)</i>
|
|
<p>
|
|
<ul>
|
|
<li> <b>Messages sorted by:</b> <a href="date.html#22">[ date ]</a><a href="index.html#22">[ thread ]</a><a href="subject.html#22">[ subject ]</a><a href="author.html#22">[ author ]</a>
|
|
<!-- next="start" -->
|
|
<li> <b>Next message:</b> <a href="0023.html">Eric Goebelbecker: "Re: sane 0.71 and microtek E3"</a>
|
|
<li> <b>Previous message:</b> <a href="0021.html">Bob van der Poel: "sane 0.71 and microtek E3"</a>
|
|
<!-- nextthread="start" -->
|
|
<!-- reply="end" -->
|
|
</ul>
|
|
<!-- body="start" -->
|
|
Bob: don't feel bad, the EXACT same thing happened to me. I was<br>
|
|
installing SANE on a P166 running Red Hat 5.0, 2.0.33 with a Microtek E3. <br>
|
|
We can get mtekscan to work, but SANE does the same thing, compiled file,<br>
|
|
pretty sure configured correctly, blah blah yackety smackety, can see the<br>
|
|
scanner, but when you scan, it waits for a minute and gives an I/O error<br>
|
|
message and the scanner needs to be turned off before it can see it again. <br>
|
|
I was reluctant to post anything because I thought I had done something<br>
|
|
wrong, but if mtekscan works, one would think I set up the SCSI stuff<br>
|
|
properly, now wouldn't one? Would really like to get this to work, else<br>
|
|
our College Sys Admin has threatened to put 95 on the machine!!! If anyone<br>
|
|
has gotten SANE to work with an E3, please write me so we can save a<br>
|
|
computer from the horrid 95 virus!!! (OK, so I have played xbill too<br>
|
|
much...) <br>
|
|
<p>
|
|
<i>>Stuff that Bob van der Poel wrote: </i><br>
|
|
<p>
|
|
<i>> First I should mention that the scanned DOES work with the old mtekscan</i><br>
|
|
<i>> program. No problems.</i><br>
|
|
<i>> ./configure ran fine for creating sane. Then did a make; make install.</i><br>
|
|
<i>> Again, noproblems</i><br>
|
|
<i>> Now, when I run xscaniamge the program seems to load, pause for a few</i><br>
|
|
<i>> seconds, then I get the bash prompt back.</i><br>
|
|
<i>> </i><br>
|
|
<i>> I can get xcam to run and load. If I press <play>, life goes on hold for</i><br>
|
|
<i>> about 1/2 minute, then I get a message about an i/o error (don't recall</i><br>
|
|
<i>> exactly). My READY light on the scanner has gone off in this process.</i><br>
|
|
<i>> </i><br>
|
|
<i>> scanimage hangs and then prints 'sane-start: error during device i/o'.</i><br>
|
|
<p>
|
|
<p>
|
|
<pre>
|
|
--
|
|
Source code, list archive, and docs: <a href="http://www.mostang.com/sane/">http://www.mostang.com/sane/</a>
|
|
To unsubscribe: echo unsubscribe sane-devel | mail <a href="mailto:majordomo@mostang.com">majordomo@mostang.com</a>
|
|
</pre>
|
|
<!-- body="end" -->
|
|
<p>
|
|
<ul>
|
|
<!-- next="start" -->
|
|
<li> <b>Next message:</b> <a href="0023.html">Eric Goebelbecker: "Re: sane 0.71 and microtek E3"</a>
|
|
<li> <b>Previous message:</b> <a href="0021.html">Bob van der Poel: "sane 0.71 and microtek E3"</a>
|
|
<!-- nextthread="start" -->
|
|
<!-- reply="end" -->
|
|
</ul>
|