Lexmark X1130
Lexmark X1150
Lexmark X1180
USB
Vendor=043d
ProdID=007c
Realtek RTS8852B
X1150: Board Number BJ4150M02001 Ver A-7 2 large processors : Realtek RTS8852B-03 37012Q1 327F - PC-Based MFP Controller Chip ( close relative to .) Lexmark 18K0205 330B31V ARM - Printer controller? 3 smaller ICs: SN105082 37AC4LT 14D0205 Silicon Controlled Rectifier BD6775 329 H91 NPN Darlington Transistor 24C01W6 B326L Serial EEPROM
As all these devices use the same id, probably they have the same hardware. Under Windows the X1130 uses the same driver as the X1150 does (and all X1100 series). The printer-scanner kit contains a usb hub inside, for the two devices: Scanner and Printer. See also the devices output of the X1130 below. Printer works with Lexmark z600 driver.
Abbout the X1150: All in one job. Printer works fine with the z600 driver. Info on the scanner chip (well the closes relative I can find) can be found here.
X1130:
(internal hub)
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 2
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=043d ProdID=007a Rev= 1.00
S: Manufacturer=Lexmark
S: Product=USB Hub
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 8mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=255ms
(printer)
T: Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=043d ProdID=007c Rev= 1.00
S: Manufacturer=Lexmark
S: Product=X1100 Series
S: SerialNumber=5509812
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 8 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 1 Ivl=250ms
(scanner)
T: Bus=01 Lev=02 Prnt=03 Port=01 Cnt=02 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=043d ProdID=007b Rev= 1.00
S: Manufacturer=Lexmark
S: Product=Lexmark X1100 Series
S: SerialNumber=5509812
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 4mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=07(print) Sub=01 Prot=02 Driver=usblp
E: Ad=05(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 16 Ivl=0ms
X1150:
T: Bus=02 Lev=02 Prnt=06 Port=00 Cnt=01 Dev#= 7 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=043d ProdID=007c Rev= 1.00
S: Manufacturer=Lexmark
S: Product=X1100 Series
S: SerialNumber=5003470
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 8 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 1 Ivl=250ms
X1150:
<device descriptor of 0x043d/0x007c at 002:004>
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 0
bDeviceSubClass 0
bDeviceProtocol 0
bMaxPacketSize0 8
idVendor 0x043D
idProduct 0x007C
bcdDevice 1.00
iManufacturer 1 ((null))
iProduct 2 ((null))
iSerialNumber 7 ((null))
bNumConfigurations 1
<configuration 0>
bLength 9
bDescriptorType 2
wTotalLength 39
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 6 ((null))
bmAttributes 224 (Self-poweredRemote Wakeup)
MaxPower 0 mA
<interface 0>
<altsetting 0>
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 255
bInterfaceSubClass 0
bInterfaceProtocol 255
iInterface 9 ((null))
<endpoint 0>
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 (in 0x01)
bmAttributes 2 (bulk)
wMaxPacketSize 64
bInterval 0 ms
bRefresh 0
bSynchAddress 0
<endpoint 1>
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 (out 0x02)
bmAttributes 2 (bulk)
wMaxPacketSize 8
bInterval 0 ms
bRefresh 0
bSynchAddress 0
<endpoint 2>
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 (in 0x03)
bmAttributes 3 (interrupt)
wMaxPacketSize 1
bInterval 250 ms
bRefresh 0
bSynchAddress 0
<trying to find out which USB chip is used>
checking for GT-6801 ...
this is not a GT-6801 (bDeviceClass = 0)
checking for GT-6816 ...
this is not a GT-6816 (bNumEndpoints = 3)
checking for MA-1017 ...
this is not a MA-1017 (bDeviceClass = 0, bInterfaceClass = 255)
checking for MA-1015 ...
this is not a MA-1015 (bDeviceClass = 0)
checking for MA-1509 ...
this is not a MA-1509 (bDeviceClass = 0)
checking for LM983[1,2,3] ...
this is not a LM983x (bEndpointAddress = 0x81, bmAttributes = 0x2, wMaxPacketSize = 0x40, bInterval = 0x0)
checking for GL646 ...
this is not a GL646 (bDeviceClass = 0, bInterfaceClass = 255)
checking for GL660+GL646 ...
this is not a GL660+GL646 (bDeviceClass = 0, bInterfaceClass = 255)
<Couldn't determine the type of the USB chip>
found USB scanner (vendor=0x043d, product=0x007c) at libusb:002:004
X1180:
T: Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=043d ProdID=007c Rev= 1.00
S: Manufacturer=Lexmark
S: Product=X1100 Series
S: SerialNumber=3277660
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=ff Driver=(none)
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 8 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 1 Ivl=250ms
If anything is wrong or missing on this page please file a bug report or use the the form for adding an unsupported device.
If you own an unsupported scanner, please send as much information as possible. Especially the output of sane-find-scanner -v -v and/or cat /proc/scsi/scsi (for SCSI scanners) or cat /proc/bus/usb/devices (for USB scanners) can help. If you dare to open the scanner, have a look at the text that's printed on the chips. That may help to identify the chipset. If you know that the scanner is similar to another one (e.g. supported by the same Windows driver), please also mention this fact.
Are you a manufacturer or vendor of scanners and one of your scanners is not supported by SANE yet? In this case please have a look at our information for manufacturers.
$Date$ $Author$