Hi John culleton,
On Saturday 14 July 2001 21:06, you wrote:
> On Saturday 14 July 2001 13:06, you wrote:
> > Which scanner are you using and how is it connected
> > (SCSI/parallel/USB)?
> >
> > Karl Heinz
> >
> > On Sat, Jul 14, 2001 at 09:50:03AM -0400, John culleton wrote:
> > > I recently upgraded to Slackware 8.0 My old version of scanmimage
> > > woldn't work. Kept getting segmentation Errors. So I loaded
> > > version 1.0.5, compiled, installed, visited /usr/local/sane.d
> > > etc. and so on.
> > >
> > > Now when I put in a command
> > > scanimage -depson:/dev/usb/scanner0
> > >
> > > the light comes on (I am making contact at least) but the scanner
> > > does not move. If I switch the scanner off I get an i-o error
> > > message. Ctrl-C does not interrupt the program.
> > >
> > > Scanner works under Win98 but the software over there is pretty
> > > restrictive. Any thoughts?
>
> Nothing in the hardware has changed. I have an Epson 1240U connected
> via my usb port. Under Slackware 7.1 it used to work.
>
> The kernel has usb software built in. And as I noted above I can make
> contact with the scanner. I just can't get it to scan.
>
> Here is a snippet from dmesg:
>
> usb.c: registered new driver usbdevfs
> usb.c: registered new driver hub
> uhci.c: USB UHCI at I/O 0x6300, IRQ 11
> usb.c: new USB bus registered, assigned bus number 1
> hub.c: USB hub found
> hub.c: 2 ports detected
> uhci.c: Linus Torvalds, Johannes Erdfelt, Randy Dunlap, Georg Acher,
> Deti Fliegl, Thomas Sailer, Roman Weissgaerber
> uhci.c: USB Universal Host Controller Interface driver
> usb.c: registered new driver usbscanner
> scanner.c: USB Scanner support registered.ub.c: USB new device
> connect on bus1/1, assigned device number 2
> hub.c: USB new device connect on bus1/2, assigned device number 3
> usb.c: USB device 3 (vend/prod 0x46d/0xc501) is not claimed by any
> active driver. (Note this device is a cordless mouse that I don't use
> at present.)
>
>
I have an Epson 1240U and upgraded to Slackware 8.0 last week, but
everything works fine for me, just as it did under Slackware 7.1 (I run
sane 1.04). Try to recompile sane 1.04 and see if it works ?
Note that the libs under 8.0 have changed significantly, which may
explain the segfaults.
-- groeten/regards, Kees Lemmens.----------------------------------------------------------------------- Department of Applied Mathematical Analysis, Faculty of Information Technology and Systems, Delft University of Technology,
Address : PO Box 5031, NL-2600 GA, Delft, The Netherlands. Phone work/home: (+31) 015-2787224/010-4740254, Fax : 015-2787209 Email : C.W.J.Lemmens@its.tudelft.nl. WWW : http://ta.twi.tudelft.nl/DV/Staff/C.W.J.Lemmens.html -----------------------------------------------------------------------
-- Source code, list archive, and docs: http://www.mostang.com/sane/ To unsubscribe: echo unsubscribe sane-devel | mail majordomo@mostang.com
This archive was generated by hypermail 2b29 : Tue Jul 17 2001 - 11:47:38 PDT