raspi-pico-aprs-tnc

A TX-only TNC (Terminal Node Controller) to generate the AFSK (Audio Frequency-Shift Keying) audio tones for APRS (Automatic Packet Reporting System) messages using a RP2040 microcontroller on a Raspberry Pi Pico board.

Block diagram showing the signal flow

An analog line-out audio signal will be generated by a band-pass filter connected to GPIO-pin 'GP0' which provides the binary PWM signal. You can probe it by a scope, listen to it by using an audio amp, or connect it to any RF transceiver to send it on the air (ham radio license required).

Image: Line-out signal (see below) probed by a DSO. We clearly see the 1200 Hz and 2200 Hz tones of the 1200 Bd 2-AFSK.

Both a static library libaprs_pico.a and an example application will be generated by the build.

Prerequisites

Your host platform for cross-compilation is assumed to be LINUX.

1. Install the Pico-SDK following the instructions given in the Raspberry Pi 'Getting Started' Guide (pdf)
2. Set the PICO_SDK_PATH environment variable to point to your Pico-SDK installation directory
3. Install the pico-extras libraries:

  cd $PICO_SDK_PATH/..
  git clone -b master https://github.com/raspberrypi/pico-extras.git
  cd pico-extras
  git submodule update --init

Hardware

We just need a simple band-pass filter to extract the analog AFSK-signal from the binary PWM signal:

The line-out voltage can be as high as 2.7 V_pp (~1 V_rms) (at full-scale volume setting in the software and high-impedance load).

Build the library and the example application

git clone https://github.com/eleccoder/raspi-pico-aprs-tnc.git
cd raspi-pico-aprs-tnc
cmake -S . -B build
cmake --build build

build/lib/libaprs_pico.a and build/aprs_pico_example[.uf2|.elf|.bin] will be generated.

Run the example application

cd build
Flash 'aprs_pico_example[.uf2|.elf|.bin]' to the Pico board as usual

The analog AFSK audio signal will be available at the filter's line-out. You can probe it by a scope, listen to it by using an audio amp, or connect it to any RF transceiver to send it on the air (ham radio license required).

Test the example application using Dire Wolf (on LINUX)

We can use the famous Dire Wolf CLI software to decode the APRS data after sampling our APRS audio signal by means of a soundcard.

1. Connect the line-out of our circuit above to the microphone input of your soundcard of your (ALSA-supported) LINUX system.
2. Check if you can hear the typical APRS 'modem-sound' on your audio output device by monitoring the input signal:

arecord -f cd -c 1 -t raw - | aplay -f cd -c 1 -t raw

3. Install Dire Wolf on your system. Probably, you just have to run:

sudo apt install direwolf

4. Let's sample the APRS audio signal fed to the soundcard and forward the audio stream to Dire Wolf:

arecord -f cd -c 1 -t raw - | direwolf

5. Enjoy the decoded APRS message:

TODO (Dec. 2022)

• Send the APRS message on the console (USB or UART) rather than hard-coding
• PTT control for RF transceivers
• Show how to physically connect to a Baofeng HT

Ingredients / Acknowledgements

• For APRS => AX.25 => PCM conversion I'm using my modified version of fsphil's ax25beacon
• For PCM => PWM conversion I'm using the pico_audio_pwm library from pico-extras (NOTE: ATTOW, maturity seems to be rather alpha/beta)