kopia lustrzana https://github.com/projecthorus/radiosonde_auto_rx
639 wiersze
27 KiB
Plaintext
639 wiersze
27 KiB
Plaintext
#
|
|
# Radiosonde Auto RX v2 Station Configuration File
|
|
#
|
|
# Copy this file to station.cfg and modify as required.
|
|
#
|
|
# If you only change a few settings, the important ones to change are:
|
|
# - [habitat] -> uploader_callsign - Your station callsign!
|
|
# - [location] -> station_lat, station_lon, station_alt - Your station location!
|
|
# - [search_params] -> min_freq, max_freq - Set these suitable for your location!
|
|
#
|
|
|
|
################
|
|
# SDR SETTINGS #
|
|
################
|
|
[sdr]
|
|
|
|
#
|
|
# SDR Type
|
|
#
|
|
# RTLSDR - Use one or more RTLSDRs
|
|
#
|
|
# EXPERIMENTAL / NOT IMPLEMENTED options:
|
|
# SpyServer - Use an Airspy SpyServer
|
|
# KA9Q - Use a KA9Q SDR Server (Not yet implemented)
|
|
# WARNING: These are still under development and may not work.
|
|
#
|
|
sdr_type = RTLSDR
|
|
|
|
|
|
#
|
|
# Number of SDRs or SDR Connection Threads to use
|
|
#
|
|
# If SDR type is set to RTLSDR above, then this number is the number of individual RTLSDRs
|
|
# that will be used, eith each RTLSDR allocated a scan or decode task.
|
|
# If more than one RTLSDR is in use, multiple [sdr_X] sections must be populated below
|
|
#
|
|
# If SDR type is either KA9Q or SpyServer, this defines the maximum number of parallel
|
|
# decoding/scan tasks. On a RPi 4, ~5 tasks are possible.
|
|
#
|
|
sdr_quantity = 1
|
|
|
|
|
|
#
|
|
# Network SDR Connection Details
|
|
#
|
|
# If using either a KA9Q or SpyServer network server, the hostname and port
|
|
# of the server needs to be defined below. Usually this will be running on the
|
|
# same machine as auto_rx, so the defaults are usually fine.
|
|
#
|
|
sdr_hostname = localhost
|
|
sdr_port = 5555
|
|
|
|
#
|
|
# Individual RTLSDR Settings
|
|
#
|
|
# Provide details of your RTLSDRs here, e.g. device numbers, gain settings, and PPM offsets.
|
|
# If using a Network SDR, do not modify any of these settings.
|
|
#
|
|
[sdr_1]
|
|
# Device Index / Serial
|
|
# If using a single RTLSDR, set this value to 0
|
|
# If using multiple SDRs, you MUST allocate each SDR a unique serial number using rtl_eeprom
|
|
# The serial number must NOT be 00000000 or 00000001, as this causes big confusion to the rtl utilities.
|
|
# i.e. to set the serial number of a (single) connected RTLSDR: rtl_eeprom -s 00000002
|
|
# Then set the device_idx below to 00000002, and repeat for the other [sdr_n] sections below
|
|
#
|
|
# For the special case when auto_rx is used entirely with a JSON-via-UDP input, set the below to TCP001
|
|
# This will bypass all RTLSDR checks and allow auto_rx to continue running.
|
|
device_idx = 0
|
|
|
|
# Frequency Correction (ppm offset)
|
|
# Refer here for a method of determining this correction using LTE signals: https://gist.github.com/darksidelemm/b517e6a9b821c50c170f1b9b7d65b824
|
|
ppm = 0
|
|
|
|
# SDR Gain Setting
|
|
# Gain settings can generally range between 0dB and 40dB depending on the tuner in use.
|
|
# Run rtl_test to confirm what gain settings are available, or use a value of -1 to use hardware automatic gain control (AGC).
|
|
# Note that this is an overall gain value, not an individual mixer/tuner gain. This is a limitation of the rtl_power/rtl_fm utils.
|
|
gain = -1
|
|
|
|
# Bias Tee - Enable the bias tee in the RTLSDR v3 Dongles.
|
|
bias = False
|
|
|
|
[sdr_2]
|
|
# As above, for the next SDR, if used. Note the warning about serial numbers.
|
|
device_idx = 00000002
|
|
ppm = 0
|
|
gain = -1
|
|
bias = False
|
|
|
|
# Add more SDR definitions here if needed. ([sdr_3], [sdr_4])
|
|
|
|
|
|
##############################
|
|
# RADIOSONDE SEARCH SETTINGS #
|
|
##############################
|
|
[search_params]
|
|
# Minimum and maximum search frequencies, in MHz.
|
|
# Australia: Use 400.05 - 403 MHz
|
|
# New Zealand: Use 400.05 - 404 MHz
|
|
# Europe: Use 400.05 - 406 MHz
|
|
# US:
|
|
# Some areas have transitioned to the 400.05 - 406 MHz band, so try 400.05 - 406
|
|
# Some areas are still using ~1680 MHz sondes, which use channels of 1676, 1678, 1680 and 1682 MHz (Thanks Tory!)
|
|
# Example only_scan for these sondes: [1676.0, 1678.0, 1680.0, 1682.0]
|
|
# In these areas I suggest using the only_scan feature below instead of using the peak-detect search.
|
|
# You may also need to apply a small offset to the frequency for decoding reliability (i.e. 1676.025 MHz) as
|
|
# the sondes are often off-frequency. For now, check in something like GQRX to get an idea of what offset is required.
|
|
#
|
|
# Note - when using either a KA9Q or SpyServer as the SDR backend, the frequency scan limits are set by the
|
|
# Server.
|
|
|
|
min_freq = 400.05
|
|
max_freq = 403.0
|
|
|
|
# After rx_timeout seconds of no valid data from a decoder, stop the decoder and go back to scanning (if a SDR is available)
|
|
rx_timeout = 180
|
|
|
|
# Frequency Lists - These must be provided as JSON-compatible lists of floats (in MHz), i.e. [400.50, 401.520, 403.200]
|
|
|
|
# only_scan - Add values to this list to *only* scan on these frequencies.
|
|
# This is for when you only want to monitor a small set of launch frequencies.
|
|
only_scan = []
|
|
|
|
# never_scan - Any values added to this list will be removed from the list of detected peaks.
|
|
# This is used to remove known spurs or other interferers from the scan list, potentially speeding up detection of a sonde.
|
|
never_scan = []
|
|
|
|
# always_scan - Any values in this list will be added to the start every scan run.
|
|
# This is useful when you know the regular frequency of a local sonde, but still want to allow detections on other frequencies.
|
|
always_scan = []
|
|
|
|
# always_decode - Always-running decoders. Only possible in a multi-SDR (or network-based SDR) system.
|
|
# List must be in the form: [[401.5,"RS41"], [402.5,"DFM"], [400.5,"M10"], [400.5,"IMET"]]
|
|
# Valid sonde types: RS41, RS92, DFM, M10, M20, IMET, IMET5, MK2LMS, LMS6, MEISEI, MRZ, MTS01
|
|
always_decode = []
|
|
|
|
|
|
####################
|
|
# STATION LOCATION #
|
|
####################
|
|
# Used by the Sondehub Uploader, APRS Uploader, and by Rotator Control
|
|
# Lat/Lon in decimal degrees, altitude in metres.
|
|
# Note: You do not need to specify your home station accurately if you don't want to!
|
|
# Feel free to use a position somewhere near your general area, that doesn't identify your home location.
|
|
#
|
|
# If this is a mobile or portable station, it is recommended to leave this at 0.0, and disable
|
|
# 'upload_listener_position' in the section below. Mobile station positions should be uploaded using
|
|
# ChaseMapper.
|
|
[location]
|
|
station_lat = 0.0
|
|
station_lon = 0.0
|
|
station_alt = 0.0
|
|
|
|
# Station Position from GPSD
|
|
# If your station is likely to move, then you may wish to have your station position updated from GPSD.
|
|
# NOTE: This feature is intended to make life slightly easier when using an auto_rx station in a portable
|
|
# capacity, in particular when using a rotator. It is *not* intended for uploading positions of mobile
|
|
# chase-cars.
|
|
# For the web interface to start up correctly, a lat/lon still needs to be entered above.
|
|
# If you are operating a stationary auto_rx station, please just set a fixed position above rather than using GPSD.
|
|
#
|
|
# If you are doing mobile balloon chasing, please use chasemapper ( https://github.com/projecthorus/chasemapper )
|
|
# which is far beter suited than auto_rx by itself...
|
|
gpsd_enabled = False
|
|
gpsd_host = localhost
|
|
gpsd_port = 2947
|
|
|
|
|
|
###################################################
|
|
# SONDEHUB / HABITAT (deprecated) UPLOAD SETTINGS #
|
|
###################################################
|
|
#
|
|
# Settings relating to uploads to the SondeHub v2 Database and tracker,
|
|
# available at https://tracker.sondehub.org/
|
|
#
|
|
# Note that uploads to the Habitat (amateur HAB) database are now disabled,
|
|
# and any references to Habitat in this config are for legacy reasons only.
|
|
[habitat]
|
|
|
|
# Uploader callsign. PLEASE CHANGE THIS TO SOMETHING UNIQUE.
|
|
# If using ChaseMapper to upload mobile station positions, ensure this callsign
|
|
# is set identically to that set in ChaseMapper.
|
|
uploader_callsign = CHANGEME
|
|
|
|
# Upload listener position to Sondehub? (So you show up on the map)
|
|
# Note that if GPSD is used, this is overriden and enabled.
|
|
# If this is a mobile or portable station, it is recommended to set this to False.
|
|
# Mobile stations should use ChaseMapper or the SondeHub Tracker to upload positions.
|
|
upload_listener_position = True
|
|
|
|
# Uploader Antenna Description.
|
|
# If upload_listener_position is enabled, this information will show up in your station description on the habhub map.
|
|
uploader_antenna = 1/4 wave monopole
|
|
|
|
[sondehub]
|
|
# Enable uploading to Sondehub v2 - please leave this enabled!
|
|
sondehub_enabled = True
|
|
|
|
# How often to push data to the SondeHub Database. (seconds)
|
|
# All received positions are cached and uploaded every X seconds.
|
|
# Uploads are gzip compressed, so don't require much data transfer.
|
|
# Users receiving Graw DFM sondes may want to set this to 30 to improve
|
|
# the chances of uploads not being rejected by our Z-check.
|
|
# (Refer: https://github.com/projecthorus/sondehub-infra/wiki/DFM-radiosonde-above-1000-and-not-enough-data-to-perform-z-check )
|
|
sondehub_upload_rate = 15
|
|
|
|
# An optional contact e-mail address.
|
|
# This e-mail address will *only* be available to the Sondehub admins, and will *only*
|
|
# be used to contact you if there is an obvious issue with your station.
|
|
# We recommend that you join the radiosonde_auto_rx mailing list to receive updates:
|
|
# https://groups.google.com/forum/#!forum/radiosonde_auto_rx
|
|
sondehub_contact_email = none@none.com
|
|
|
|
|
|
|
|
########################
|
|
# APRS UPLOAD SETTINGS #
|
|
########################
|
|
# Settings for uploading to radiosondy.info
|
|
#
|
|
# IMPORTANT APRS NOTE
|
|
#
|
|
# As of auto_rx version 1.5.10, we are limiting APRS output to only radiosondy.info,
|
|
# and only on the non-forwarding port.
|
|
# This decision was not made lightly, and is a result of the considerable amount of
|
|
# non-amateur traffic that radiosonde flights are causing within the APRS-IS network.
|
|
# Until some form of common format can be agreed to amongst the developers of *all*
|
|
# radiosonde tracking software to enable radiosonde telemetry to be de-duped,
|
|
# I have decided to help reduce the impact on the wider APRS-IS network by restricting
|
|
# the allowed servers and ports.
|
|
# If you are using another APRS-IS server that *does not* forward to the wider APRS-IS
|
|
# network and want it allowed, then please raise an issue at
|
|
# https://github.com/projecthorus/radiosonde_auto_rx/issues
|
|
#
|
|
# You are of course free to fork and modify this codebase as you wish, but please be aware
|
|
# that this goes against the wishes of the radiosonde_auto_rx developers to not be part
|
|
# of the bigger problem of APRS-IS congestion.
|
|
# As of 2022-03-01, radiosonde traffic has been filtered from aprs.fi, so even if you do
|
|
# modify the code, you still won't see sondes on that map.
|
|
# APRS-IS is a *shared resource*, intended for the use of all amateur radio operators, and
|
|
# for many years we have been treating it as a playground to dump large amounts of non-amateur
|
|
# traffic into, so we can see weather balloons on a map.
|
|
# Instead of congesting this shared resource with this non-amateur traffic, we should instead
|
|
# be moving to using databases and sites specialised for this purpose, for example sondehub.org
|
|
|
|
[aprs]
|
|
# Enable APRS upload (you will also need to change some options below!)
|
|
aprs_enabled = False
|
|
|
|
# APRS-IS Login Information
|
|
# The aprs_user field can have an SSID on the end if desired, i.e. N0CALL-4
|
|
aprs_user = N0CALL
|
|
# APRS-IS Passcode. You can generate one for your callsign here: https://apps.magicbug.co.uk/passcode/
|
|
aprs_pass = 00000
|
|
|
|
# APRS Upload Rate - Upload a packet every X seconds.
|
|
# This has a lower limit of 30 seconds, to avoid flooding radiosondy.info
|
|
# Please be respectful, and do not attempt to upload faster than this.
|
|
upload_rate = 30
|
|
|
|
# APRS-IS server to upload to.
|
|
# Currently we only support uploading to radiosondy.info
|
|
# When using port 14580, packets are not forwarded to the wider APRS-IS network, and hence
|
|
# are help reduce the huge amount of non-amateur traffic that ends up in APRS-IS from
|
|
# radiosondes.
|
|
aprs_server = radiosondy.info
|
|
|
|
# APRS-IS Port Number to upload to.
|
|
#
|
|
# Port 14590 - Packets stay within radiosondy.info and do not congest the wider APRS-IS
|
|
# network.
|
|
#
|
|
aprs_port = 14580
|
|
|
|
# APRS Station Location Beaconing
|
|
# If enabled, you will show up on APRS using the aprs_user callsign set above.
|
|
# This also requires your station location to be set in the above [location] section.
|
|
station_beacon_enabled = False
|
|
|
|
# Station beaconing rate, in minutes.
|
|
station_beacon_rate = 30
|
|
|
|
# Station beacon comment.
|
|
# <version> will be replaced with the current auto_rx version number
|
|
station_beacon_comment = radiosonde_auto_rx SondeGate v<version>
|
|
|
|
# Station Beacon Icon
|
|
# The APRS icon to use, as defined in http://www.aprs.org/symbols.html
|
|
# Note that the two characters that define the icon need to be concatenated. Examples:
|
|
# Antenna Tower = /r
|
|
# House with Yagi = /y
|
|
# Satellite Dish = /` (This is required if you want to show up on radiosondy.info's station list.)
|
|
station_beacon_icon = /`
|
|
|
|
# Custom Object name / Callsign to be used when uploading telemetry to APRS-IS (Max 9 chars)
|
|
# WARNING: THIS SHOULD BE LEFT AT THE DEFAULT OF <id> UNLESS YOU HAVE A VERY GOOD REASON
|
|
# TO CHANGE IT!
|
|
#
|
|
# Using <id> means the uploads from multiple stations remain consistent, and we don't end up with
|
|
# lots of duplicate sondes on APRS-IS. If you enable the station location beaconing (below), maps
|
|
# like aprs.fi and radiosondy.info will show your station as the receiver.
|
|
#
|
|
# If used, this field should be either a callsign with a -11 or -12 suffix (i.e. N0CALL-12),
|
|
# or <id>, which will be replaced with the radiosondes serial number.
|
|
#
|
|
# WARNING - If running multiple RTLSDRs, setting this to a fixed callsign will result in odd behaviour on the online tracker.
|
|
# DO NOT SET THIS TO ANYTHING OTHER THAN <id> IF YOU ARE USING MORE THAN ONE SDR!
|
|
aprs_object_id = <id>
|
|
|
|
# Confirmation of the above setting.
|
|
# Set to True to confirm use of the custom object ID set above.
|
|
# Please read the notes above before setting this to True.
|
|
aprs_use_custom_object_id = False
|
|
|
|
# The APRS-IS beacon comment. The following fields can be included:
|
|
# <freq> - Sonde Frequency, e.g. 401.520 MHz
|
|
# <type> - Sonde Type (e.g. RS41-SG, DFM09, etc....)
|
|
# <id> - Sonde Serial Number (i.e. M1234567)
|
|
# <vel_v> - Sonde Vertical Velocity (i.e. -5.1m/s)
|
|
# <temp> - Sonde reported temperature. If no temp data available, this will report -273 degC.
|
|
# <humidity> - Sonde reported humidity.
|
|
# <pressure> - Sonde reported pressure
|
|
# <batt> - Battery Voltage (e.g. 3.1V)
|
|
# The default comment (below) is compatible with radiosondy.info's parsers, and should only be modified
|
|
# if absolutely necessary.
|
|
aprs_custom_comment = Clb=<vel_v> t=<temp> h=<humidity> p=<pressure> <freq> Type=<type> ser=<id> Radiosonde
|
|
|
|
|
|
###########################
|
|
# CHASEMAPPER DATA OUTPUT #
|
|
###########################
|
|
# Settings for pushing data into Chasemapper and/or OziPlotter
|
|
# Oziplotter receives data via a basic CSV format, via UDP.
|
|
# Chasemapper can receive data in either the basic CSV format, or in the more descriptive 'payload summary' JSON format.
|
|
[oziplotter]
|
|
# How often to output data (seconds)
|
|
ozi_update_rate = 5
|
|
|
|
# Enable the 'OziMux' basic CSV output
|
|
# Note - this cannot be enabled in a multi-SDR configuration.
|
|
ozi_enabled = False
|
|
|
|
# OziMux UDP Broadcast output port.
|
|
# Set to 8942 to send packets directly into OziPlotter, or set to 55681 to send via OziMux
|
|
ozi_port = 8942
|
|
|
|
# Payload summary UDP output, which is the preferred input if using ChaseMapper.
|
|
# Using this output allows multiple sondes to be plotted in Chasemapper.
|
|
# As of 2019-05, this is enabled by default.
|
|
payload_summary_enabled = True
|
|
payload_summary_port = 55673
|
|
|
|
|
|
#######################
|
|
# EMAIL NOTIFICATIONS #
|
|
#######################
|
|
# Sends an email notification to the specified address when a new Sonde is detected
|
|
[email]
|
|
email_enabled = False
|
|
|
|
# Send an e-mail for each new radiosonde observed.
|
|
launch_notifications = True
|
|
|
|
# Send e-mails when a radiosonde is detected descending near your station location
|
|
landing_notifications = True
|
|
|
|
# Send e-mails when an encrypted radiosonde is detected.
|
|
encrypted_sonde_notifications = True
|
|
|
|
# Range threshold for Landing notifications (km from your station location)
|
|
landing_range_threshold = 30
|
|
|
|
# Altitude threshold for Landing Notifications (metres)
|
|
# Notifications will only occur for sondes which have been observed descending (>2m/s descent rate) below this altitude
|
|
# for at least 10 observations
|
|
landing_altitude_threshold = 1000
|
|
|
|
# Enable sending critical error notifications (one that cause auto_rx to completely crash out) via email.
|
|
# WARNING: If an error is persistent and you are running as a systemd service, this could result
|
|
# in many e-mails being sent!
|
|
error_notifications = False
|
|
|
|
# Server details. Note that usually Port 465 is used for SSL auth, and 587 is used for TLS.
|
|
smtp_server = localhost
|
|
smtp_port = 25
|
|
|
|
# Authentication type, Valid options are: None, TLS, and SSL
|
|
smtp_authentication = None
|
|
|
|
# If using authentication, the following fields need to be populated:
|
|
smtp_login = None
|
|
smtp_password = None
|
|
|
|
# 'Source' e-mail
|
|
from = sonde@localhost
|
|
|
|
# Destination emails. You can send to multiple addresses by separating each address with a semicolon,
|
|
# i.e. test@test.com;test2@test2.com
|
|
to = someone@example.com
|
|
|
|
# Custom subject field. The following fields can be included:
|
|
# <freq> - Sonde Frequency, i.e. 401.520 MHz
|
|
# <type> - Sonde Type (RS94/RS41)
|
|
# <id> - Sonde Serial Number (i.e. M1234567)
|
|
subject = <type> Sonde launch detected on <freq>: <id>
|
|
|
|
# Custom nearby landing subject field. The following fields can be included:
|
|
# <freq> - Sonde Frequency, i.e. 401.520 MHz
|
|
# <type> - Sonde Type (RS94/RS41)
|
|
# <id> - Sonde Serial Number (i.e. M1234567)
|
|
nearby_landing_subject = Nearby Radiosonde Landing Detected - <id>
|
|
|
|
|
|
###################
|
|
# ROTATOR CONTROL #
|
|
###################
|
|
# auto_rx can communicate with an instance of rotctld, on either the local machine or elsewhere on the network.
|
|
# This is, admittedly, a bit of a waste of an az/el rotator setup when a vertical antenna usually works fine,
|
|
# but it's still fun :-)
|
|
[rotator]
|
|
# WARNING - This should not be enabled in a multi-SDR configuration.
|
|
# Your station location (defined in the [location] section above) must also be defined.
|
|
rotator_enabled = False
|
|
# How often to update the rotator position. (Seconds)
|
|
update_rate = 30
|
|
# Only move the rotator if the new position is more than X degrees in azimuth or elevation from the current position.
|
|
rotation_threshold = 5.0
|
|
# Hostname / Port of the rotctld instance.
|
|
rotator_hostname = 127.0.0.1
|
|
rotator_port = 4533
|
|
# Rotator Homing.
|
|
# If enabled, turn to a 'home' location when scanning for sondes.
|
|
# This could be used to point an antenna at a known radiosonde launch location.
|
|
rotator_homing_enabled = False
|
|
# Wait until x minutes after no sonde data received before moving to the home location.
|
|
rotator_homing_delay = 10
|
|
# Rotator home azimuth/elevation, in degrees true.
|
|
rotator_home_azimuth = 0.0
|
|
rotator_home_elevation = 0.0
|
|
|
|
|
|
###########
|
|
# LOGGING #
|
|
###########
|
|
[logging]
|
|
# If enabled, a log file will be written to ./log/ for each detected radiosonde.
|
|
per_sonde_log = True
|
|
|
|
# Enable logging of system-level logs to disk.
|
|
# This is the equivalent of starting auto_rx with the --systemlog option, but only takes effect after the config file is read.
|
|
# These logs will end up in the log directory.
|
|
save_system_log = False
|
|
|
|
# Enable logging of debug messages.
|
|
# This is the equivalent of starting auto_rx with the -v option, but only takes effect after the config file is read.
|
|
# This setting, in combination with save_system_log (above), can help provide detailed information when debugging
|
|
# auto_rx operational issues.
|
|
enable_debug_logging = False
|
|
|
|
# Enable logging of RS41 Calibration data ('subframe' data)
|
|
# This is saved as a binary file with file suffix _subframe.bin
|
|
save_cal_data = False
|
|
|
|
###########################
|
|
# WEB INTERFACE SETTINNGS #
|
|
###########################
|
|
[web]
|
|
# Server Host - Can be set to :: to listen on IPv6
|
|
web_host = 0.0.0.0
|
|
# Server Port - Ports below 1024 can only be used if you run auto_rx as root (not recommended)
|
|
web_port = 5000
|
|
# Archive Age - How long to keep a sonde telemetry in memory for the web client to access, in minutes
|
|
# Note: The higher this number, the more data the client will need to load in on startup
|
|
archive_age = 120
|
|
|
|
# Enable control over the scanner, and starting/stopping decoders from the web interface.
|
|
# A password must also be set (below).
|
|
# USERS ENABLE THIS AT THEIR OWN RISK!!
|
|
web_control = False
|
|
|
|
# Password for controls on the web interface. The main interface will still be publicly available.
|
|
# Note that as the web interface is HTTP-only, this password will be sent over the internet in the clear,
|
|
# so don't re-use passwords!
|
|
web_password = none
|
|
|
|
# KML refresh rate
|
|
kml_refresh_rate = 10
|
|
|
|
|
|
##################
|
|
# DEBUG SETTINGS #
|
|
##################
|
|
[debugging]
|
|
# WARNING - Enabling these settings can result in lots of SD-card IO, potentially
|
|
# reducing the life of the card. These should only be enabled to collect data for
|
|
# debugging purposes.
|
|
|
|
# Save the audio that a detection pass is run over to: detect_<SDR_ID>.wav
|
|
# This file is over-written with every new detection.
|
|
save_detection_audio = False
|
|
|
|
# Save the audio from the output from a sonde decode chain to decode_<SDR_ID>.wav
|
|
# This file is over-written with each new sonde decoded for a particular SDR.
|
|
# This only works for the 'legacy' FM-based demodulators.
|
|
save_decode_audio = False
|
|
|
|
# Save the decimated IQ data from an experimental sonde decode chain to decode_IQ_<SDR_ID>.bin
|
|
# This will be in complex signed 16-bit int format, and may be either 48 kHz or 96 kHz.
|
|
# Note: This will use a LOT of disk space.
|
|
save_decode_iq = False
|
|
|
|
# Save raw hexadecimal radiosonde frame data. This is useful to provide data for telemetry analysis.
|
|
# Raw hex data is saved to the logging directory with a filename of format YYYYMMDD-HHMMSS_<type>_<freq>.raw
|
|
# Saving raw data is currently only supported for: RS41, LMS6-1680, LMS6-400, M10, M20, IMET-4
|
|
save_raw_hex = False
|
|
|
|
|
|
#####################
|
|
# ADVANCED SETTINGS #
|
|
#####################
|
|
# These control low-level settings within various modules.
|
|
# Playing with them may result in odd behaviour.
|
|
[advanced]
|
|
# Scanner - Receive bin width (Hz)
|
|
search_step = 800
|
|
# Scanner - Minimum SNR for a peak to be detected. The lower the number, the more peaks detected.
|
|
snr_threshold = 10
|
|
# Scanner - Maximum number of peaks to search through during a scan pass.
|
|
# Increase this if you have lots of spurious signals, though this will increase scan times.
|
|
max_peaks = 10
|
|
# Scanner - Minimum distance between detected peaks (Hz)
|
|
min_distance = 1000
|
|
# Scanner - Scan Dwell Time - How long to observe the specified spectrum for.
|
|
scan_dwell_time = 20
|
|
# Scanner - Detection Dwell time - How long to wait for a sonde detection on each peak.
|
|
detect_dwell_time = 5
|
|
# Scanner - Delay between scans. We should delay a short amount between scans to allow for decoders and other actions to jump in.
|
|
scan_delay = 10
|
|
# Quantize search results to x Hz steps. Useful as most sondes are on 10 kHz frequency steps.
|
|
quantization = 10000
|
|
# Decoder Spacing Limit - Only start a new decoder if it is separated from an existing decoder by at least
|
|
# this value (Hz). This helps avoid issues where a drifting radiosonde is detected on two adjacent channels.
|
|
# If you regularly encounter radiosondes on adjacent (10kHz) channels, then set this value to 5000.
|
|
decoder_spacing_limit = 15000
|
|
# Temporary Block Time (minutes) - How long to block encrypted or otherwise non-decodable sondes for.
|
|
temporary_block_time = 120
|
|
# Upload when (seconds_since_utc_epoch%upload_rate) == 0. Otherwise just delay upload_rate seconds between uploads.
|
|
# Setting this to True with multple uploaders should give a higher chance of all uploaders uploading the same frame,
|
|
# however the upload_rate should not be set too low, else there may be a chance of missing upload slots.
|
|
synchronous_upload = True
|
|
# Only accept a payload ID as valid until it has been seen N times.
|
|
# This helps avoid corrupted callsigns getting onto the map.
|
|
payload_id_valid = 3
|
|
# Paths to the rtl_fm and rtl_power utilities. If these are on your system path, then you don't need to change these.
|
|
sdr_fm_path = rtl_fm
|
|
sdr_power_path = rtl_power
|
|
|
|
# Paths to SpyServer client (https://github.com/miweber67/spyserver_client) utilities, for experimental SpyServer Client support
|
|
# At the moment we assume these are in the auto_rx directory.
|
|
ss_iq_path = ./ss_iq
|
|
ss_power_path = ./ss_power
|
|
|
|
|
|
################################
|
|
# DEMODULATOR / DECODER TWEAKS #
|
|
################################
|
|
|
|
#
|
|
# Alternate Decode Chains
|
|
#
|
|
# NOTE: This section will be deprecated soon, with the fsk_demod chains used permanently.
|
|
#
|
|
# These (not so) experimental demod chains use David Rowe's fsk_demod modem.
|
|
# They have much better drift handling performance, and so may be better suited for
|
|
# 1680 MHz sondes, but use considerably more CPU. Recommend use of a Pi 3 or better.
|
|
# The experimental decoders can be enabled/disabled independently for each radiosonde type.
|
|
# It is recommended that these are always left enabled.
|
|
rs41_experimental = True
|
|
rs92_experimental = True
|
|
dfm_experimental = True
|
|
m10_experimental = True
|
|
lms6-400_experimental = True
|
|
imet54_experimental = True
|
|
meisei_experimental = True
|
|
|
|
# LMS6-1680 Decoder options:
|
|
# False = Less CPU, possibly worse weak-signal performance.
|
|
# True = Higher CPU (Pushing a RPi 3 to its limits), possibly better weak-signal performance.
|
|
lms6-1680_experimental = False
|
|
|
|
# MRZ sondes have not yet been tested with the fsk_demod flowgraph in the wild.
|
|
# If someone can confirm that this works, I'll set it to True by default!
|
|
mrz_experimental = False
|
|
|
|
# Note: As iMet-4 sondes use AFSK, using fsk_demod does not give any advantage, so there is no experimental decoder for them.
|
|
|
|
# Optimize 1680 MHz Scanning for RS92-NGP Sondes
|
|
# This flag sets the use of IQ detection when scanning for 1680 MHz sondes, which allows RS92-NGP sondes
|
|
# to be detected reliably.
|
|
# Set this to True if you are sure that only RS92-NGPs are flying in your area.
|
|
ngp_tweak = False
|
|
|
|
# Wideband Radiosonde Detection:
|
|
# Enables some tweaks to better handle detection and decoding of the following radiosonde types:
|
|
# - Intermet iMet-1/4 (Wideband versions)
|
|
# - Weathex WxR-301d
|
|
# If this is enabled in areas with 'narrowband' sondes as well (RS41, DFM, narrowband iMet, etc...) there will likely
|
|
# be degradation in detection and decode performance.
|
|
wideband_sondes = False
|
|
|
|
|
|
######################
|
|
# POSITION FILTERING #
|
|
######################
|
|
# These are used to discard positions which are clearly bad, such as where the payload has jumped halfway around the world,
|
|
# or has suddenly ended up in orbit.
|
|
#
|
|
# Users can also decide to temporary block sondes which are outside of a radius range.
|
|
#
|
|
[filtering]
|
|
# Discard positions with an altitude greater than 50000 metres.
|
|
max_altitude = 50000
|
|
|
|
# Discard positions from sondes which are outside the following min/max radius limits.
|
|
# This requires the ground-station location to be set.
|
|
max_radius_km = 1000
|
|
min_radius_km = 0
|
|
|
|
# Temporarily block the frequency of sondes which report a position outside of the above limits.
|
|
# WARNING: This may cause sondes which sometimes report glitchy positions (RS92, DFM) to be blocked.
|
|
# (True or False)
|
|
radius_temporary_block = False
|
|
|
|
# Reported Time Threshold
|
|
# Discard positions if the sonde's reported time is more than X hours from the system time.
|
|
# This helps catch glitches around 00Z UTC from iMet & LMS6 sondes, and bad CRC checks from
|
|
# DFM sondes.
|
|
sonde_time_threshold = 3 |