#include "pwm_cluster.hpp"
#include <cstdio> // TOREMOVE once done debugging
#include "hardware/gpio.h" // TOREMOVE once done debugging
#include "hardware/clocks.h"
#include "pwm_cluster.pio.h"

// Uncomment the below line to enable debugging
#define DEBUG_MULTI_PWM

namespace pimoroni {

#ifdef DEBUG_MULTI_PWM
    static const uint DEBUG_SIDESET = 17;
#endif

int data_dma_channel;
int ctrl_dma_channel;
Sequence sequences[NUM_BUFFERS];
Sequence loop_sequences[NUM_BUFFERS];
uint sequence_index = 0;

volatile uint read_index = 0;
volatile uint last_written_index = 0;


uint irq_gpio = 15;
uint write_gpio = 16;

void __isr pwm_dma_handler() {
  // Clear the interrupt request.
  dma_hw->ints0 = 1u << data_dma_channel;

  gpio_put(irq_gpio, 1); //TOREMOVE Just for debug

  Sequence* seq;

  // If new data been written since the last time, switch to reading that buffer
  if(last_written_index != read_index) {
    read_index = last_written_index;
    seq = &sequences[read_index];
  }
  else {
    seq = &loop_sequences[read_index];
  }

  dma_channel_set_trans_count(data_dma_channel, seq->size << 1, false);
  dma_channel_set_read_addr(data_dma_channel, seq->data, true);

  gpio_put(irq_gpio, 0); //TOREMOVE Just for debug
}

    /***
     * From RP2040 datasheet
     * *
     * One disadvantage of this technique is that we don’t start to reconfigure the channel until some time after the channel
makes its last transfer. If there is heavy interrupt activity on the processor, this may be quite a long time, and therefore
quite a large gap in transfers, which is problematic if we need to sustain a high data throughput.
This is solved by using two channels, with their CHAIN_TO fields crossed over, so that channel A triggers channel B when it
completes, and vice versa. At any point in time, one of the channels is transferring data, and the other is either already
configured to start the next transfer immediately when the current one finishes, or it is in the process of being
reconfigured. When channel A completes, it immediately starts the cued-up transfer on channel B. At the same time, the
interrupt is fired, and the handler reconfigures channel A so that it is ready for when channel B completes.
     * */
    

PWMCluster::PWMCluster(PIO pio, uint sm, uint pin_mask)
: pio(pio)
, sm(sm)
, pin_mask(pin_mask & ((1u << NUM_BANK0_GPIOS) - 1))
, channel_count(0)
, channels(nullptr)
, wrap_level(0) {

  // Create the channel mapping
  for(uint pin = 0; pin < NUM_BANK0_GPIOS; pin++) {
    if(bit_in_mask(pin, pin_mask)) {
      channel_to_pin_map[channel_count] = pin;
      channel_count++;
    }
  }

  // Initialise all the channels this PWM will control
  if(channel_count > 0) {
    channels = new ChannelState[channel_count];
  }
}


PWMCluster::PWMCluster(PIO pio, uint sm, uint pin_base, uint pin_count)
: pio(pio)
, sm(sm)
, pin_mask(0x00000000)
, channel_count(0)
, channels(nullptr)
, wrap_level(0) {

  // Create the pin mask and channel mapping
  uint pin_end = MIN(pin_count + pin_base, NUM_BANK0_GPIOS);
  for(uint pin = pin_base; pin < pin_end; pin++) {
    pin_mask |= (1u << pin);
    channel_to_pin_map[channel_count] = pin;
    channel_count++;
  }

  // Initialise all the channels this PWM will control
  if(channel_count > 0) {
    channels = new ChannelState[channel_count];
  }
}

PWMCluster::PWMCluster(PIO pio, uint sm, const uint8_t *pins, uint32_t length)
: pio(pio)
, sm(sm)
, pin_mask(0x00000000)
, channel_count(0)
, channels(nullptr)
, wrap_level(0) {

  // Create the pin mask and channel mapping
  for(uint i = 0; i < length; i++) {
    uint8_t pin = pins[i];
    if(pin < NUM_BANK0_GPIOS) {
      pin_mask |= (1u << pin);
      channel_to_pin_map[channel_count] = pin;
      channel_count++;
    }
  }

  // Initialise all the channels this PWM will control
  if(channel_count > 0) {
    channels = new ChannelState[channel_count];
  }
}

PWMCluster::PWMCluster(PIO pio, uint sm, std::initializer_list<uint8_t> pins)
: pio(pio)
, sm(sm)
, pin_mask(0x00000000)
, channel_count(0)
, channels(nullptr)
, wrap_level(0) {

  // Create the pin mask and channel mapping
  for(auto pin : pins) {
    if(pin < NUM_BANK0_GPIOS) {
      pin_mask |= (1u << pin);
      channel_to_pin_map[channel_count] = pin;
      channel_count++;
    }
  }

  // Initialise all the channels this PWM will control
  if(channel_count > 0) {
    channels = new ChannelState[channel_count];
  }
}

PWMCluster::~PWMCluster() {
  dma_channel_unclaim(data_dma_channel);
  dma_channel_unclaim(ctrl_dma_channel);
  pio_sm_set_enabled(pio, sm, false);
#ifdef DEBUG_MULTI_PWM
  pio_remove_program(pio, &debug_pwm_cluster_program, pio_program_offset);
#else
  pio_remove_program(pio, &pwm_cluster_program, pio_program_offset);
#endif
#ifndef MICROPY_BUILD_TYPE
  // pio_sm_unclaim seems to hardfault in MicroPython
  pio_sm_unclaim(pio, sm);
#endif
  // Reset all the pins this PWM will control back to an unused state
  for(uint channel = 0; channel < channel_count; channel++) {
    gpio_set_function(channel_to_pin_map[channel], GPIO_FUNC_NULL);
  }

  delete[] channels;
}

bool PWMCluster::init() {
#ifdef DEBUG_MULTI_PWM
  pio_program_offset = pio_add_program(pio, &debug_pwm_cluster_program);
#else
  pio_program_offset = pio_add_program(pio, &pwm_cluster_program);
#endif

  gpio_init(irq_gpio);
  gpio_set_dir(irq_gpio, GPIO_OUT);
  gpio_init(write_gpio);
  gpio_set_dir(write_gpio, GPIO_OUT);

  // Initialise all the channels this PWM will control
  for(uint channel = 0; channel < channel_count; channel++) {
    pio_gpio_init(pio, channel_to_pin_map[channel]);
  }

  // Set their default state and direction
  pio_sm_set_pins_with_mask(pio, sm, 0x00, pin_mask);
  pio_sm_set_pindirs_with_mask(pio, sm, pin_mask, pin_mask);

#ifdef DEBUG_MULTI_PWM
  pio_gpio_init(pio, DEBUG_SIDESET);
  pio_sm_set_consecutive_pindirs(pio, sm, DEBUG_SIDESET, 1, true);
#endif

#ifdef DEBUG_MULTI_PWM
  pio_sm_config c = debug_pwm_cluster_program_get_default_config(pio_program_offset);
#else
  pio_sm_config c = pwm_cluster_program_get_default_config(pio_program_offset);
#endif
  sm_config_set_out_pins(&c, 0, irq_gpio); //TODO change this to be 32
#ifdef DEBUG_MULTI_PWM
  sm_config_set_sideset_pins(&c, DEBUG_SIDESET);
#endif
  sm_config_set_out_shift(&c, false, true, 32);
  sm_config_set_fifo_join(&c, PIO_FIFO_JOIN_NONE); // We actively do not want a joined FIFO even though we are not needing the RX


  float div = clock_get_hz(clk_sys) / 5000000;
  sm_config_set_clkdiv(&c, div);

  pio_sm_init(pio, sm, pio_program_offset, &c);
  pio_sm_set_enabled(pio, sm, true);

  data_dma_channel = dma_claim_unused_channel(true);
  /*ctrl_dma_channel = dma_claim_unused_channel(true);

  dma_channel_config ctrl_config = dma_channel_get_default_config(ctrl_dma_channel);
  channel_config_set_transfer_data_size(&ctrl_config, DMA_SIZE_32);
  //channel_config_set_read_increment(&ctrl_config, false);
  //channel_config_set_write_increment(&ctrl_config, false);
  channel_config_set_read_increment(&ctrl_config, true);
  channel_config_set_write_increment(&ctrl_config, true);
  channel_config_set_ring(&ctrl_config, true, 3); // 1 << 3 byte boundary on write ptr
  channel_config_set_ring(&ctrl_config, false, 3); // 1 << 3 byte boundary on read ptr

  dma_channel_configure(
    ctrl_dma_channel,
    &ctrl_config,
    //The below two work
    //&dma_hw->ch[data_dma_channel].al1_transfer_count_trig,
    //&transfer_count,
    //1,
    //These two do not
    //&dma_hw->ch[data_dma_channel].al3_read_addr_trig,
    //&((uint32_t *)buffer),
    &dma_hw->ch[data_dma_channel].al3_transfer_count, // Initial write address
    &control_blocks[0],
    2,
    false
  );*/

  dma_channel_config data_config = dma_channel_get_default_config(data_dma_channel);
  channel_config_set_bswap(&data_config, false);
  channel_config_set_dreq(&data_config, pio_get_dreq(pio, sm, true));
  channel_config_set_transfer_data_size(&data_config, DMA_SIZE_32);
  channel_config_set_read_increment(&data_config, true);
  //channel_config_set_chain_to(&data_config, ctrl_dma_channel);
  //channel_config_set_ring(&data_config, false, 7);

  dma_channel_configure(
    data_dma_channel,
    &data_config,
    &pio->txf[sm],
    NULL,
    0,
    false);

  dma_channel_set_irq0_enabled(data_dma_channel, true);

  // Configure the processor to run dma_handler() when DMA IRQ 0 is asserted
  irq_set_exclusive_handler(DMA_IRQ_0, pwm_dma_handler);
  irq_set_enabled(DMA_IRQ_0, true);

  // Set up the transition buffers
  for(uint i = 0; i < NUM_BUFFERS; i++) {
    Sequence& seq = sequences[i];
    seq = Sequence();
    seq.data[0].delay = 10; // Need to set a delay otherwise a lockup occurs when first changing frequency
    Sequence& looping_seq = loop_sequences[i];
    looping_seq = Sequence();
    looping_seq.data[0].delay = 10; // Need to set a delay otherwise a lockup occurs when first changing frequency
  }

  // Manually call the handler once, to trigger the first transfer
  pwm_dma_handler();

  //dma_start_channel_mask(1u << ctrl_dma_channel);
  return true;
}

uint8_t PWMCluster::get_chan_count() const {
  return channel_count;
}

uint8_t PWMCluster::get_chan_pin(uint8_t channel) const {
  assert(channel < channel_count);
  return channel_to_pin_map[channel];
}

uint32_t PWMCluster::get_chan_level(uint8_t channel) const {
  assert(channel < channel_count);
  return channels[channel].level;
}

void PWMCluster::set_chan_level(uint8_t channel, uint32_t level, bool load) {
  assert(channel < channel_count);
  channels[channel].level = level;
  if(load)
    load_pwm();
}

uint32_t PWMCluster::get_chan_offset(uint8_t channel) const {
  assert(channel < channel_count);
  return channels[channel].offset;
}

void PWMCluster::set_chan_offset(uint8_t channel, uint32_t offset, bool load) {
  assert(channel < channel_count);
  channels[channel].offset = offset;
  if(load)
    load_pwm();
}

bool PWMCluster::get_chan_polarity(uint8_t channel) const {
  assert(channel < channel_count);
  return channels[channel].polarity;
}

void PWMCluster::set_chan_polarity(uint8_t channel, bool polarity, bool load) {
  assert(channel < channel_count);
  channels[channel].polarity = polarity;
  if(load)
    load_pwm();
}

uint32_t PWMCluster::get_wrap() const {
  return wrap_level;
}

void PWMCluster::set_wrap(uint32_t wrap, bool load) {
  wrap_level = MAX(wrap, 1);  // Cannot have a wrap of zero!
  if(load)
    load_pwm();
}

// These apply immediately, so do not obey the PWM update trigger
void PWMCluster::set_clkdiv(float divider) {
  pio_sm_set_clkdiv(pio, sm, divider);
}

// These apply immediately, so do not obey the PWM update trigger
void PWMCluster::set_clkdiv_int_frac(uint16_t integer, uint8_t fract) {
  pio_sm_set_clkdiv_int_frac(pio, sm, integer, fract);
}

void PWMCluster::load_pwm() {
  gpio_put(write_gpio, 1);

  uint data_size = 0;
  uint looping_data_size = 0;

  uint pin_states = 0; // Start with all pins low

  // Check if the data we last wrote has been picked up by the DMA yet?
  const bool read_since_last_write = (read_index == last_written_index);

  // Go through each channel that we are assigned to
  for(uint channel = 0; channel < channel_count; channel++) {
    ChannelState &state = channels[channel];

    // Invert this channel's initial state if it's polarity invert is set
    if(state.polarity) {
      pin_states |= (1u << channel_to_pin_map[channel]); // Set the pin
    }

    const uint channel_start = state.offset;
    const uint channel_end = (state.offset + state.level);
    const uint channel_wrapped_end = channel_end % wrap_level;

    // If the data has been read, copy the channel overruns from that sequence. Otherwise, keep the ones we had previously stored.
    if(read_since_last_write) {
      // This condition was added to deal with cases of load_pwm() being called multiple
      // times between DMA reads, and thus loosing memory of the previous sequence's overruns
      state.overrun = state.next_overrun;
    }
    state.next_overrun = 0u; // Always clear the next channel overruns, as we are loading new data

    // Did the previous sequence overrun the wrap level?
    if(state.overrun > 0) {
      // Flip the initial state so the pin starts "high" (or "low" if polarity inverted)
      pin_states ^= (1u << channel_to_pin_map[channel]);

      // Is our end level before our start level?
      if(channel_wrapped_end < channel_start) {
        // Yes, so add a transition to "low" (or "high" if polarity inverted) at the end level, rather than the overrun (so our pulse takes effect earlier)
        PWMCluster::sorted_insert(transitions, data_size, TransitionData(channel, channel_wrapped_end, state.polarity));
      }
      else if(state.overrun < channel_start) {
        // No, so add a transition to "low" (or "high" if polarity inverted) at the overrun instead
        PWMCluster::sorted_insert(transitions, data_size, TransitionData(channel, state.overrun, state.polarity));
      }
    }

    // Is the state level greater than zero, and the start level within the wrap?
    if(state.level > 0 && channel_start < wrap_level) {
      // Add a transition to "high" (or "low" if polarity inverted) at the start level
      PWMCluster::sorted_insert(transitions, data_size, TransitionData(channel, channel_start, !state.polarity));
      PWMCluster::sorted_insert(looping_transitions, looping_data_size, TransitionData(channel, channel_start, !state.polarity));

      // If the channel has overrun the wrap level, record by how much
      if(channel_wrapped_end < channel_start) {
          state.next_overrun = channel_wrapped_end;
      }
    }

    // Is the state level within the wrap?
    if(state.level < wrap_level) {
      // Is the end level within the wrap too?
      if(channel_end < wrap_level) {
        // Add a transition to "low" (or "high" if polarity inverted) at the end level
        PWMCluster::sorted_insert(transitions, data_size, TransitionData(channel, channel_end, state.polarity));
      }

      // Add a transition to "low" (or "high" if polarity inverted) at the wrapped end level
      PWMCluster::sorted_insert(looping_transitions, looping_data_size, TransitionData(channel, channel_wrapped_end, state.polarity));
    }
  }

  gpio_put(write_gpio, 0); //TOREMOVE

  // Introduce "Loading Zone" transitions to the end of the sequence to
  // prevent the DMA interrupt firing many milliseconds before the sequence ends.
  uint32_t zone_inserts = MIN(LOADING_ZONE_SIZE, wrap_level - LOADING_ZONE_POSITION);
  for(uint32_t i = zone_inserts + LOADING_ZONE_POSITION; i > LOADING_ZONE_POSITION; i--) {
    PWMCluster::sorted_insert(transitions, data_size, TransitionData(wrap_level - i));
    PWMCluster::sorted_insert(looping_transitions, looping_data_size, TransitionData(wrap_level - i));
  }

  gpio_put(write_gpio, 1); //TOREMOVE

  // Read | Last W = Write
  // 0    | 0      = 1 (or 2)
  // 0    | 1      = 2
  // 0    | 2      = 1
  // 1    | 0      = 2
  // 1    | 1      = 2 (or 0)
  // 1    | 2      = 0
  // 2    | 0      = 1
  // 2    | 1      = 0
  // 2    | 2      = 0 (or 1)

  // Choose the write index based on the read and last written indices (using the above table)
  uint write_index = (read_index + 1) % NUM_BUFFERS;
  if(write_index == last_written_index) {
    write_index = (write_index + 1) % NUM_BUFFERS;
  }

  populate_sequence(transitions, data_size, sequences[write_index], pin_states);
  populate_sequence(looping_transitions, looping_data_size, loop_sequences[write_index], pin_states);

  // Update the last written index so that the next DMA interrupt picks up the new sequence
  last_written_index = write_index;

  gpio_put(write_gpio, 0); //TOREMOVE
}

// Derived from the rp2 Micropython implementation: https://github.com/micropython/micropython/blob/master/ports/rp2/machine_pwm.c
bool PWMCluster::calculate_pwm_factors(float freq, uint32_t& top_out, uint32_t& div256_out) {
  bool success = false;
  uint32_t source_hz = clock_get_hz(clk_sys) / PWM_CLUSTER_CYCLES;

  // Check the provided frequency is valid
  if((freq >= 0.01f) && (freq <= (float)(source_hz >> 1))) {
    uint64_t div256_top = (uint64_t)((float)((uint64_t)source_hz << 8) / freq);
    uint64_t top = 1;

    while(true) {
        // Try a few small prime factors to get close to the desired frequency.
        if((div256_top >= (11 << 8)) && (div256_top % 11 == 0) && (top * 11 <= MAX_PWM_CLUSTER_WRAP)) {
            div256_top /= 11;
            top *= 11;
        }
        else if((div256_top >= (7 << 8)) && (div256_top % 7 == 0) && (top * 7 <= MAX_PWM_CLUSTER_WRAP)) {
            div256_top /= 7;
            top *= 7;
        }
        else if((div256_top >= (5 << 8)) && (div256_top % 5 == 0) && (top * 5 <= MAX_PWM_CLUSTER_WRAP)) {
            div256_top /= 5;
            top *= 5;
        }
        else if((div256_top >= (3 << 8)) && (div256_top % 3 == 0) && (top * 3 <= MAX_PWM_CLUSTER_WRAP)) {
            div256_top /= 3;
            top *= 3;
        }
        else if((div256_top >= (2 << 8)) && (top * 2 <= MAX_PWM_CLUSTER_WRAP)) {
            div256_top /= 2;
            top *= 2;
        }
        else {
            break;
        }
    }

    // Only return valid factors if the divisor is actually achievable
    if(div256_top >= 256 && div256_top <= (UINT8_MAX << 8)) {
      top_out = top;
      div256_out = div256_top;

      success = true;
    }
  }
  return success;
}

bool PWMCluster::bit_in_mask(uint bit, uint mask) {
  return ((1u << bit) & mask) != 0;
}

void PWMCluster::sorted_insert(TransitionData array[], uint &size, const TransitionData &data) {
  uint i = size;
  for(; (i > 0 && array[i - 1].level > data.level); i--) {
    array[i] = array[i - 1];
  }
  array[i] = data;
  size++;
}

void PWMCluster::populate_sequence(const TransitionData transitions[], const uint &data_size, Sequence &seq_out, uint &pin_states_in_out) const {
  seq_out.size = 0; // Reset the sequence, otherwise we end up appending and weird things happen

  if(data_size > 0) {
    uint data_index = 0;
    uint current_level = 0;

    // Populate the selected write sequence with pin states and delays
    while(data_index < data_size) {
      uint next_level = wrap_level; // Set the next level to be the wrap, initially

      do {
        const TransitionData &transition = transitions[data_index];

        // Is the level of this transition at the current level being checked?
        if(transition.level <= current_level) {
          // Yes, so add the transition state to the pin states mask, if it's not a dummy transition
          if(!transition.dummy) {
            if(transition.state)
              pin_states_in_out |= (1u << channel_to_pin_map[transition.channel]);
            else
              pin_states_in_out &= ~(1u << channel_to_pin_map[transition.channel]);
          }

          data_index++; // Move on to the next transition
        }
        else {
          // No, it is higher, so set it as our next level and break out of the loop
          next_level = transition.level;
          break;
        }
      } while(data_index < data_size);

      // Add the transition to the sequence
      seq_out.data[seq_out.size].mask = pin_states_in_out;
      seq_out.data[seq_out.size].delay = (next_level - current_level) - 1;
      seq_out.size++;

      current_level = next_level;
    }
  }
  else {
    // There were no transitions (either because there was a zero wrap, or no channels because there was a zero wrap?),
    // so initialise the sequence with something, so the PIO functions correctly
    seq_out.data[seq_out.size].mask = 0u;
    seq_out.data[seq_out.size].delay = wrap_level - 1;
    seq_out.size++;
  }
}
}